A 1 milliohm shunt resistor turns tens of amps into a few tens of millivolts that a BMS or converter controller can read. Walsin lists 48 shunts at 1 milliohm, 28 of them in 2512 and eight rated 3 W, with 22 tagged AEC-Q200. Venatech is the authorised Walsin distributor in Hong Kong, serving Egypt.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for BMS, power-conversion and component engineers in Egypt’s Suez Canal Economic Zone (SCZONE), Ain Sokhna and the wider battery storage and solar supply chain. Walsin Technology (Walsin) is the line we are authorised for. We parsed all 79 chip resistor upload files, Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_79.xlsx, on 16 November 2026, kept the metal and thick film current sense series, and counted distinct part numbers at exactly 0.001 ohm. Every part number below is real.
What is Sungrow building in the Suez Canal Economic Zone?
A battery energy storage factory with 10 GWh of planned yearly output. ESS News reported on 27 August 2026 that Sungrow broke ground on a 50 million US dollar BESS plant in the China-Egypt TEDA zone at Ain Sokhna, inside the SCZONE, with production due in April 2027 and more than 100 direct jobs.
The report gives about 50,000 square metres of land and about 18,000 square metres of buildings, says PowerChina is the construction contractor, and says output will serve Egypt and export markets. Those are the publication’s figures, not ours. A storage system of that scale is built from battery racks, each with its own battery management electronics, plus power conversion and auxiliary boards. Every one of those measures current, and in the high-current paths the usual sensor is a low-value metal shunt.
Where does a 1 milliohm shunt resistor sit in a battery storage system?
In series with the current it measures, read by an amplifier across its two ends. At 1 milliohm, 50 A produces only 50 mV across the shunt and 2.5 W of heat, which is why storage, BMS and converter designs reach for values around 1 milliohm at high current.
Typical positions are the rack or module current path for state-of-charge counting and over-current protection, the DC input of a power stage, and fan or auxiliary rails at lower currents and higher values. The design trade is signal against heat: a lower value wastes less power but leaves a smaller voltage for the amplifier, so offset and layout matter more. Metal plate and metal foil shunts are chosen here over thick film because they reach lower values with better temperature behaviour. Our guide to low-ohm current sense: thick film versus metal and the note on passives for a battery management system cover the selection logic.
How many 1 milliohm shunt resistors does Walsin list?
- We counted 48 distinct Walsin parts at 1 milliohm: 28 in 2512, 17 in 1206 and three four-terminal metal foil parts in 0306, 0612 and 1225; 25 are 1 percent and 23 are 5 percent, and 22 are tagged AEC-Q200 in the export.
| Size | Parts at 1 milliohm | Rated power | Construction |
|---|---|---|---|
| 2512 | 8 | 3 W | Metal plate (WW25A, WW25B) |
| 2512 | 12 | 2 W | Metal plate (WW25K, WW25N, WW25R) |
| 2512 | 8 | 1 W | Metal plate (WW25J, WW25M) |
| 1206 | 17 | 1/2 W to 1 W | Metal plate (WW12J, K, M, N, R) |
| 1225 | 1 | 2 W | Metal foil, four-terminal (WW25Y) |
| 0612 | 1 | 1 W | Metal foil, four-terminal (WW12Y) |
| 0306 | 1 | 1/2 W | Metal foil, four-terminal (WW06Y) |
TCR in the export is 70 ppm/°C or better on 26 of the 48, 75 ppm/°C on 15 and 100 ppm/°C on 7. The four-terminal parts give a separate Kelvin sense pair, which helps where the solder joint would otherwise sit inside the measurement. We have not seen the 1 milliohm slice of Walsin’s shunt range counted anywhere else.
How much current can a 1 milliohm, 2512 shunt carry?
On power rating alone, about 54 A at 3 W, 44 A at 2 W and 31 A at 1 W. The arithmetic is current equals the square root of power over resistance, so a 3 W, 1 milliohm part reaches its rating near 54 A, before any derating for temperature, pad size or airflow.
In practice the current you can run continuously is lower, because the rated power assumes a terminal temperature set out in each datasheet, for example ASC_WW25A.pdf for the 3 W WW25A family, and it falls off above that point. Wide copper, several vias to inner planes and a short, symmetrical sense route keep the part cooler and the reading cleaner. Where the current is higher still, designers parallel two shunts or move to a lower value.
Which Walsin parts cross a 1 milliohm, 2512, 1 percent brief at 2 W or more?
Ten parts meet the value, size, tolerance and power. At 1 milliohm, 2512, 1 percent and 2 W or more, we found ten Walsin metal plate shunts across five families, five of them in AEC-Q200 automotive versions, plus near misses on power, tolerance and size.
| Brief: 1 milliohm, 2512, 1%, 2 W or more | Walsin part | Rated power | TCR | Match / mismatch | Your incumbent |
|---|---|---|---|---|---|
| Highest rating | WW25AR001FTL |
3 W | 70 ppm | Match | |
| Same, AEC-Q200 | WW25AR001FTLJ |
3 W | 70 ppm | Match, adds AEC-Q200 | |
| Second 3 W family | WW25BR001FTL |
3 W | 70 ppm | Match | |
| 2 W | WW25KR001FTL |
2 W | 70 ppm | Match | |
| 2 W, AEC-Q200 | WW25NR001FTLJ |
2 W | 70 ppm | Match, adds AEC-Q200 | |
| 2 W, AEC-Q200, wider TCR | WW25RR001FTLJ |
2 W | 100 ppm | Match on the brief; TCR 100 ppm against 70 | |
| Lower power | WW25MR001FTL |
1 W | 70 ppm | Mismatch in power | |
| 5 percent | WW25AR001JTL |
3 W | 70 ppm | Mismatch in tolerance | |
| Four-terminal foil | WW25YR001FTL |
2 W | 100 ppm | Mismatch in size (1225) and footprint |
Footprints differ between families even within 2512, so check the land pattern and the sense-pad layout against both datasheets before you swap. Leave the last column for your current part; our post on cross-referencing chip resistors to Walsin lists the fields to check first.
How Venatech helps: what can we supply to an Ain Sokhna battery storage line?
Crosses for the whole sensing and power-path list, from one supplier in Hong Kong. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, including all 48 shunts in this post.
On our shelf in Hong Kong (snapshot 9 Nov 2026) are three thick film low-ohm sense resistors in 0805, WW08WR270FTL, WW08WR390FTL and WW08WR470FTL, for lower-current auxiliary rails; the 1 milliohm metal parts are to order, so request a quote and we source them through our authorised Walsin channel. Paste your shunt lines into the cross-reference tool, upload the BOM at /bom/, or see the dated ready stock list and the chip resistor range. We quote small lots fast and confirm availability, date code and lead time on each quote, with no promise in advance. Import questions stay with your compliance team.
The short version
- Sungrow broke ground on a 10 GWh, 50 million US dollar BESS factory at Ain Sokhna in the SCZONE, with production due in April 2027 (ESS News, 27 August 2026).
- Walsin lists 48 shunt resistors at 1 milliohm: 28 in 2512, 17 in 1206 and three four-terminal foil parts.
- Eight of the 2512 parts are rated 3 W, which is about 54 A on power alone before derating.
- 22 of the 48 are tagged AEC-Q200 in Walsin’s export.
Send us the current sense lines from your rack BMS or power stage and we will return the Walsin crosses with every difference stated. What continuous current does your main shunt carry?
Related reading
- Low-ohm current sense: thick film versus metal
- Passives for a battery management system
- Current sense resistor TCR: zero of 10,428 reach 50 ppm
- Cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 16 November 2026.
Sources
Fetched 16 November 2026.
- ESS News, Sungrow breaks ground on 10 GWh battery storage factory in Egypt, 27 August 2026: https://www.ess-news.com/2026/08/27/sungrow-breaks-ground-on-10-gwh-battery-storage-factory-in-egypt/
- Venatech chip resistor upload files Venatech_ChipR_Upload_01.xlsx to _79.xlsx and Walsin datasheets ASC_WW25A.pdf, ASC_WW25N.pdf and ASC_WW25Y_4T.pdf as linked in the export, re-measured 16 November 2026; Venatech ready stock snapshot dated 9 November 2026.
Frequently asked questions
How many 1 milliohm shunt resistors does Walsin make?
48 in our count of 16 November 2026: 28 in 2512, 17 in 1206 and three four-terminal metal foil parts in 0306, 0612 and 1225, from 1/2 W to 3 W.
What is the highest power 1 milliohm shunt in Walsin’s 2512 range?
3 W, in the WW25A and WW25B metal plate families, for example WW25AR001FTL and its AEC-Q200 version WW25AR001FTLJ.
How much current can a 1 milliohm, 3 W shunt resistor carry?
About 54 A on rated power alone, from current equals the square root of power over resistance. Derate for temperature and board layout using the datasheet curve.
Are Walsin 1 milliohm shunts AEC-Q200?
22 of the 48 are tagged AEC-Q200 in Walsin’s export, all of them part numbers ending in J or V. Ask for the qualification report for the exact part.
Does Venatech stock shunt resistors for Egypt?
We hold stock in Hong Kong. Three thick film low-ohm 0805 lines are on our shelf in Hong Kong (snapshot 9 Nov 2026); the 1 milliohm metal shunts are quoted through our authorised Walsin channel.
Can Venatech supply battery storage makers in the Suez Canal Economic Zone?
Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Egypt. Use the cross-reference tool or upload a BOM; confirm import rules with your compliance team.