A high value resistor, 10 megohm and up, sets the gain of the transimpedance amplifier behind a photodiode. Walsin lists 1,616 chip resistors at 10 megohm or more, 447 of them at 100 ppm, reaching 100 megohm in 17 parts, for photonics boards in Hamamatsu, Japan. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for analog designers and component buyers at photodetector, optical sensor, imaging and instrument makers in Hamamatsu, Shizuoka Prefecture, Japan, and at the board assemblers around them. Walsin Technology (Walsin) is the line we are authorised for. We counted the high-resistance end of our chip resistor upload files, Venatech_ChipR_Upload_01.xlsx onwards (234,378 distinct part numbers), on 16 November 2026, and checked the results against our ready stock snapshot dated 9 November 2026.
What is Hamamatsu Photonics adding in Hamamatsu?
A new front-end building for optical semiconductors at its head-office plant. MONOist reported on 3 July 2025 that Hamamatsu Photonics had finished a new building for front-end optical semiconductor production at its head-office plant in Hamamatsu, an investment of about 37 billion yen including equipment, with operation scheduled from December 2025.
The report said the building roughly doubles production space and adds an 8-inch wafer line beside the existing 6-inch line, for a capacity of about 8,000 wafers a month on an 8-inch basis. An earlier MONOist report, on 8 April 2025, covered a new back-end building at the company’s Shingai plant in the same city, for dicing, assembly and inspection of optical semiconductor devices including image sensors. Those are the company’s figures as reported, not ours. More photodiodes and image sensors leaving Hamamatsu means more amplifier, sensor-module and instrument boards designed around them, and every photodiode channel needs a feedback network. We make no statement about any company’s suppliers.
Why does a photodiode amplifier need a high value resistor?
Because the feedback resistor sets the gain, and small photocurrents need a large one. In a transimpedance amplifier the output voltage is the photocurrent times the feedback resistance, so a 10 nA signal gives 100 mV across 10 megohm; a larger resistor also adds less current noise, which is why low-light channels push towards 100 megohm.
The resistor is only half the feedback network. A small capacitor, often 0.5 pF to a few picofarads in C0G, sits across it to set bandwidth and keep the amplifier stable against the photodiode’s own capacitance. Three resistor fields then decide whether a part fits. Tolerance sets gain accuracy between channels. TCR sets how far the gain drifts with temperature, so 100 ppm against 200 ppm matters in an instrument. Surface leakage matters at these values too, so board cleanliness and coating are part of the design. Our post on chip resistors above 10 megohm covers the series, and what resistor TCR actually buys you works through the drift arithmetic.
How many high value chip resistors does Walsin list?
1,616 at 10 megohm or more. We counted 1,616 distinct Walsin chip resistors at 10 megohm or above in our export, spread across eight series groups and nine case sizes from 0201 to 2512; 447 carry a TCR of 100 ppm, and 17 reach 100 megohm.
| Series group | Parts at 10 megohm or more |
|---|---|
| Thick Film High Voltage | 524 |
| Thick Film High Ohm (above 10 megohm) | 419 |
| Thick Film Anti-Surge | 270 |
| Thick Film High Power | 236 |
| Thick Film General Purpose | 144 |
| Trimmable, High Precision Thick Film and Arrays | 23 |
By size, 1206 has the most at 356, then 0603 at 303 and 0805 at 284, with 145 in 0402 and 30 in 0201. The dedicated High Ohm series is not the only route: the High Voltage group holds more parts at these values, and the 447 parts at 100 ppm sit mostly in the High Power (234) and High Voltage (181) groups, while every High Ohm part is rated 200 ppm. At 100 megohm, the 17 parts include WF06G1006FTL in 0603 at 1 percent and WF06P1006FTR in 0603 at 100 ppm. We have not seen this split published anywhere else.
Which Walsin parts answer a 10 megohm, 0603, 1 percent, 100 ppm brief?
Nine, from three series groups. At exactly 10 megohm in 0603 we found 38 Walsin part numbers; nine combine 1 percent or tighter with 100 ppm, from the General Purpose, High Voltage (including its UL-certified line) and High Power groups.
| Brief: 10 megohm, 0603, 1%, 100 ppm | Walsin part | Series group | Match / mismatch | Your incumbent |
|---|---|---|---|---|
| General purpose | WR06W1005FTL |
General Purpose | Match | |
| High voltage | WK06V1005FTL |
High Voltage | Match; adds voltage rating | |
| Tighter tolerance | WK06V1005DTL |
High Voltage | Match, 0.5 percent | |
| UL safety certified | WF06N1005FTL |
High Voltage, UL | Match | |
| Automotive grade | MR06W1005FTL |
General Purpose, automotive | Mismatch: 200 ppm | |
| High Ohm series | WF06G106 JTL |
High Ohm | Mismatch: 5 percent, 200 ppm | |
| Commodity 5 percent | WR06X106 JTL |
General Purpose | Mismatch: 5 percent |
Note the embedded space in the 5 percent part numbers; paste them exactly as shown. Leave the last column for your current part and compare TCR, rated voltage and power against both datasheets. Our guide to cross-referencing chip resistors to Walsin explains how the part-number fields decode.
What sits next to the feedback resistor, and what is on the Hong Kong shelf?
Fifty-eight small C0G capacitors. The 10 megohm and higher lines are to order, so request a quote and we source them through our authorised Walsin channel; for the feedback capacitor beside them, 58 Walsin 0402 C0G parts at 10 pF or below are on our shelf in Hong Kong (snapshot 9 Nov 2026).
Those 58 come from 1,721 Walsin 0402 C0G part numbers at 10 pF or below that we checked against the snapshot. They include 0402N0R5B500 at 0.5 pF, 0402N1R0B500 at 1.0 pF and 0402N2R2B500 at 2.2 pF, all 50 V at plus or minus 0.1 pF, and high Q options such as HH15N1R1A500 at 1.1 pF. The ready stock list is a dated snapshot and stock moves; we confirm availability, date code and lead time on each quote. The chip resistor range page lists every Walsin resistor series.
How Venatech helps
Cross the whole photodiode front end in one paste. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, covering both the high value resistors and the C0G feedback capacitors in this post.
Paste your resistor and capacitor lines into the cross-reference tool, and every difference from your original is stated, TCR and tolerance included. For a full sensor-module BOM, upload it at /bom/ and request a quote through the site. We serve Japan from Hong Kong in small lots, which suits instrument builds and prototype runs, and the design and qualification decisions stay with your team.
The short version
- Hamamatsu Photonics finished a front-end optical semiconductor building in Hamamatsu worth about 37 billion yen, operating from December 2025 (MONOist, 3 July 2025).
- Walsin lists 1,616 chip resistors at 10 megohm or more; 447 carry 100 ppm and 17 reach 100 megohm.
- A 10 megohm, 0603, 1 percent, 100 ppm brief returns nine Walsin parts, including
WR06W1005FTLandWK06V1005FTL. - 58 Walsin 0402 C0G feedback capacitors at 10 pF or below are on our shelf in Hong Kong (snapshot 9 Nov 2026).
Send us the feedback-network lines from your Hamamatsu photodetector or sensor board and we will return the Walsin crosses with every difference stated. What gain drift can your channel tolerate across temperature?
Related reading
- Chip resistors above 10 megohm
- What resistor TCR actually buys you
- Thin film versus thick film chip resistors
- Free cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 16 November 2026
Sources
Fetched 16 November 2026.
- MONOist, Hamamatsu Photonics new front-end optical semiconductor building at head-office plant, 3 July 2025: https://monoist.itmedia.co.jp/mn/articles/2507/03/news043.html
- MONOist, Hamamatsu Photonics new back-end building at Shingai plant, 8 April 2025: https://monoist.itmedia.co.jp/mn/articles/2504/08/news093.html
- Venatech chip resistor upload files Venatech_ChipR_Upload_01.xlsx onwards, MLCC upload files Venatech_MLCC_Upload_01.xlsx to _08.xlsx and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.
Frequently asked questions
What is a high value resistor?
A resistor of roughly 10 megohm or more, used where currents are tiny, such as photodiode amplifiers, electrometers and high-voltage dividers. Walsin lists 1,616 chip resistors at 10 megohm or above in our count of 16 November 2026.
How high do Walsin chip resistor values go?
100 megohm, in 17 parts from 0402 to 2512, including WF06G1006FTL in 0603 at 1 percent.
Which Walsin part crosses a 10 megohm, 0603, 1 percent, 100 ppm resistor?
WR06W1005FTL in the General Purpose group, or WK06V1005FTL in the High Voltage group. Compare TCR, rated voltage and power against both datasheets.
Why does TCR matter for a transimpedance amplifier feedback resistor?
The amplifier gain is set by the resistor, so its temperature coefficient becomes gain drift. A 100 ppm part drifts half as much as a 200 ppm part over the same temperature range.
Does Venatech hold high value resistors in Hong Kong?
The 10 megohm and higher lines are sourced on request through our authorised Walsin channel. For the feedback capacitor, 58 Walsin 0402 C0G parts at 10 pF or below are on our ready stock snapshot dated 9 November 2026.
Can Venatech supply photonics and sensor makers in Hamamatsu, Japan?
Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots into Japan. Use the free cross-reference tool or upload a BOM; confirm import rules with your compliance team.