A low TCR current sense resistor keeps a current reading honest as a power board heats up. For semiconductor and power electronics teams in Austria, Walsin lists 44 parts in 2512 at 2 W from 25 to 50 milliohm at 50 ppm, the window Stackpole gives for CSS2512 and CSRF2512. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for power electronics and test engineers and buyers at Austrian makers of GaN and SiC power stages, evaluation boards, burn-in and test equipment and industrial power supplies. Walsin Technology (Walsin) is the line we are authorised for; Stackpole Electronics (SEI) is a line we supply, so a CSS2512 or CSRF2512 on your parts list can be quoted as it is or crossed to Walsin. We measured every Walsin figure below on 16 November 2026 in our Walsin current sense export, Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx, and checked our ready stock snapshot dated 9 November 2026. Stackpole figures come only from Stackpole’s resistors-for-medical-applications release of 2 May 2019 on seielect.com, fetched the same day; the CSS datasheet did not load for us that day, so confirm each Stackpole figure against it.
What did the EU approve for semiconductors in Austria in October 2026?
319 million euros of state aid for GaN in Villach. Euronews reported on 28 October 2026 that the European Commission approved 319 million euros of Austrian state aid under the EU Chips Act for Infineon’s 1.1 billion euro upgrade in Villach, Carinthia, to build what Infineon calls the first high-volume GaN power fab on 300 millimetre wafers.
The report said the 300 millimetre wafer yields 2.3 times more chips than a 200 millimetre one, and that the upgrade is expected to be complete in 2034. Those are the Commission’s and Infineon’s figures as reported, not ours. Semiconductor work around Villach draws in power-electronics design, test and equipment work: GaN evaluation boards, burn-in racks, power supplies and the instruments that characterise devices. Each of those boards measures current, and many measure it through a 2512 shunt. Our current sense resistor TCR note explains why TCR is the specification to read first.
Why do GaN power and test boards need a low TCR current sense resistor?
Because the shunt heats up with the current it measures. A shunt at 2 W in 2512 can run tens of degrees above the board, and every degree shifts its value by its TCR: a 50 ppm part moves 0.25 percent over a 50 degree rise, a 200 ppm part 1 percent, enough to break a test limit.
On a GaN power stage the shunt sets overcurrent protection and loop gain; on a burn-in or characterisation board it is the measurement itself, so drift turns into a wrong device reading. At 25 to 50 milliohm a 2 W shunt reaches about 8.9 A at 25 milliohm and 6.3 A at 50 milliohm by the square-root-of-power-over-resistance rule, a range that suits evaluation boards, PFC and LLC stages and per-channel burn-in sensing. Low inductance matters too at GaN edge rates, which favours metal element shunts over long serpentine designs. Our low-ohm current sense: thick film versus metal note compares the constructions.
How many Walsin 2 W 2512 current sense parts reach 50 ppm from 25 to 50 milliohm?
- We filtered Walsin’s current sense rows to 2512, 2 W and 50 ppm or better between 25 and 50 milliohm and counted 44 distinct part numbers at ten values: 20 metal foil parts at 1 percent and 24 metal plate parts, 12 at 1 percent and 12 at 5 percent.
| Walsin construction | Parts at 2 W, 50 ppm | Values (milliohm) | Tolerance (export) | Example |
|---|---|---|---|---|
| Metal foil | 20 | 25, 27, 30, 33, 35, 36, 40, 45, 47, 50 | 1 percent | WW25DR025FTL |
| Metal plate | 12 | 25, 30, 33, 35, 40, 50 | 1 percent | WW25NR050FTL |
| Metal plate | 12 | 25, 30, 33, 35, 40, 50 | 5 percent | WW25NR050JTL |
Each value comes as a general part and an automotive part, for example WW25DR050FTL and WW25DR050FTLJ. So 32 of the 44 are 1 percent parts. We have not seen this 2 W, 50 ppm, 25 to 50 milliohm cell counted elsewhere. Our export has no current or inductance column, so the amps here come from the power-and-resistance rule; confirm current and inductance in Walsin’s datasheet.
Which Walsin parts cross a Stackpole CSS2512 or CSRF2512?
At every value from 25 to 50 milliohm. Stackpole’s release of 2 May 2019 describes CSRF2512 and CSS2512 as 2 W current sense resistors used from 25 to 50 milliohm with a TCR of 50 ppm or better, applied there to X-ray machines, with CSS2512 for the more robust requirement.
| Your brief (CSS2512 or CSRF2512 style) | Walsin part | Walsin size, power, TCR (export) | Match / mismatch | Your incumbent |
|---|---|---|---|---|
| 25 milliohm, 2 W, 50 ppm, 1 percent | WW25DR025FTL |
2512, 2 W, 50 ppm, metal foil | Match on size, value, power, TCR | |
| 33 milliohm, 2 W, 50 ppm, 1 percent | WW25DR033FTL |
2512, 2 W, 50 ppm, metal foil | Match on size, value, power, TCR | |
| 47 milliohm, 2 W, 50 ppm, 1 percent | WW25DR047FTL |
2512, 2 W, 50 ppm, metal foil | Match on size, value, power, TCR | |
| 50 milliohm, 2 W, 50 ppm, 1 percent | WW25NR050FTL |
2512, 2 W, 50 ppm, metal plate | Match on size, value, power, TCR | |
| Construction and tolerance | any of the above | metal foil or metal plate | Stackpole’s release does not state CSS or CSRF construction or tolerance: mismatch possible, compare datasheets |
What should an Austrian power electronics team check before switching?
Inductance and TCR at your edge rate and temperature. Check the shunt’s inductance against your GaN switching edges, the TCR across your real hot-spot temperature, then pad layout and Kelvin sensing; a few nanohenries on a fast edge can add more error than a 50 ppm TCR does over 50 degrees.
Compare the pulse and overload ratings where the shunt also sees short-circuit tests, which is common on device test equipment. Use four-terminal Kelvin routing on the new pads. For automotive-tagged parts, ask for the qualification report; Walsin’s datasheets say compliant and Venatech makes no qualification claim of its own. Test equipment and medical uses carry their own approvals; we give no certification or compliance advice, so confirm with your compliance team. Our what resistor TCR actually buys you note puts numbers on the trade.
How Venatech helps
Cross the sense lines in one paste. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating size, value, tolerance, TCR and power as match or mismatch.
Paste your shunt lines into the cross-reference tool, or upload the parts list at BOM upload. On our shelf in Hong Kong (snapshot 9 Nov 2026) are three Walsin thick film current sense lines in 0805, WW08WR270FTL, WW08WR390FTL and WW08WR470FTL, at 0.27, 0.39 and 0.47 ohm, 1 percent, 1/4 W, for lower-current sensing; see ready stock. The 2 W, 50 ppm 2512 parts are not on it, so request a quote and we source them through our authorised Walsin channel. Stackpole CSS and CSRF lines can be quoted too; Stackpole is a line we supply, and Walsin is the line we are authorised for. We serve Austrian buyers from Hong Kong in small lots and confirm availability, date code and lead time on each quote, with no price, lead-time or stock guarantee. The chip resistor range lists every Walsin family.
The short version
- The European Commission approved 319 million euros of Austrian state aid for Infineon’s 1.1 billion euro GaN upgrade in Villach, per Euronews on 28 October 2026.
- Walsin lists 44 current sense parts at 2 W in 2512 from 25 to 50 milliohm at 50 ppm; 32 are 1 percent.
- Every value in the Stackpole CSS2512 and CSRF2512 window has a Walsin match on size, power and TCR.
- At GaN edge rates, check inductance as well as TCR.
Send us the shunt lines from your power stage or test board, and we will return the Walsin crosses with every difference stated. How hot does your shunt run at full load?
Related reading
- Current sense resistor TCR
- Low-ohm current sense: thick film versus metal
- What resistor TCR actually buys you
- Cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 16 November 2026.
Sources
Fetched 16 November 2026.
- Euronews, “EU approves 319 million in state aid to Austrian first-of-a-kind next-generation semiconductor” factory, 28 October 2026: https://www.euronews.com/2026/10/28/eu-approves-319-million-in-state-aid-to-austrian-first-of-a-kind-next-generation-semicondu
- Stackpole Electronics release on resistors for medical applications, 2 May 2019: https://seielect.com/news/20190502_Resistors_for_Medical_Applications.pdf
- Venatech Walsin current sense export (Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx) and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.
Frequently asked questions
What is a low TCR current sense resistor?
A shunt whose value changes little with temperature, usually 50 ppm per degree Celsius or better. On a power board that heats up, it keeps the current reading and the overcurrent trip point stable.
How many Walsin 2 W 2512 current sense parts are 50 ppm from 25 to 50 milliohm?
44 in our export at ten values: 20 metal foil parts at 1 percent and 24 metal plate parts, 12 at 1 percent and 12 at 5 percent.
Which Walsin part crosses a Stackpole CSS2512 at 25 milliohm?
WW25DR025FTL, a 2512, 25 milliohm, 1 percent, 2 W metal foil part at 50 ppm in our export, or WW25DR025FTLJ for the automotive version. Compare tolerance, inductance and pulse rating on both datasheets.
Why does the EU approval for Villach matter to power electronics buyers in Austria?
The Commission approved 319 million euros of state aid on 28 October 2026 for a 300 millimetre GaN power fab in Villach, expected complete in 2034. More GaN devices mean more evaluation, test and power boards that need stable current sensing.
Do you hold 2 W 2512 current sense resistors in stock in Hong Kong?
Not on our ready stock snapshot dated 9 November 2026; three 0805 thick film current sense lines are. Request a quote for the 2512 parts and we source them through our authorised Walsin channel, from Hong Kong in small lots, with no lead-time promise.
Is Venatech authorised for Stackpole?
No. Venatech is the authorised Walsin distributor in Hong Kong; Stackpole is a line we supply, and we quote Stackpole CSS and CSRF lines alongside the Walsin cross.