For a current sense resistor in AI data centre power built in the UK, Walsin Technology (Walsin) lists 1,188 metal low-ohm part numbers, and 58 of them sit at 1 milliohm or less. Venatech, Walsin’s authorised distributor in Hong Kong, crosses each one against your shunt and quotes it for UK teams.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for a power or purchasing engineer in the UK who designs server power supplies, power shelves, PDUs or the monitoring boards that sit on a busbar. We parsed Walsin’s metal current sense export Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx (1,188 distinct part numbers) and our stock snapshot as at 9 November 2026. The news was fetched on 17 November 2026.
What did the UK government open for an AI supercomputer data centre?
A competition worth up to 180 million pounds. Data Centre Review reported on 12 November 2026 that the UK government opened a competition on 11 November offering up to 180 million pounds for a data centre to host the next national AI supercomputer, with the first 10 MW of IT load targeted for 31 December 2027 and 30 MW by March 2029.
The same report says bidders need written evidence of a grid connection offer for at least 14 MVA of import capacity in phase one, rising to 41 MVA in phase two, that applications close at midday on 25 November, and that the outcome is expected by 8 January 2027. The money covers electrical systems, cooling and connectivity, not the supercomputer hardware, and it sits within the 750 million pounds the government first announced for the supercomputer in June 2026. For UK power electronics teams, that is a funded site where every megawatt passes through supplies, shelves and distribution boards that measure their own current.
Where does a current sense resistor sit in data centre power?
Wherever the controller needs to know the current. A current sense resistor, or shunt, sits in the output and input paths of server power supplies, in the hot-swap and e-fuse stage on each board, in 48 V to 12 V or point-of-load converters, and in PDU and busbar monitoring, where a voltage of a few tens of millivolts tells the controller how many amps are flowing.
At AI rack power levels, currents are high and voltages are low, so the resistance has to be tiny to keep the loss small. A 1 milliohm shunt carrying 40 A drops 40 mV and dissipates 1.6 W; a 5 milliohm part at the same current would burn 8 W. That is why metal plate and metal foil parts, with their low resistance and low temperature coefficient, dominate these positions. Our note on thick film versus metal low-ohm current sense explains the trade, and passives for AI server power stages maps the rest of the stage.
How many metal current sense resistors does Walsin list at 1 milliohm or less?
58 part numbers, and 114 at 2 milliohms or less. We parsed all 1,188 distinct part numbers in Walsin’s metal current sense export. 58 sit at 1 milliohm or less, including 10 at 0.5 or 0.75 milliohm; 114 reach 2 milliohms or less; and 317 reach 5 milliohms or less.
| Walsin metal current sense resistors, measured 17 Nov 2026 | Part numbers |
|---|---|
| All metal low-ohm part numbers | 1,188 |
| In 2512 | 625 |
| In 1206 | 375 |
| At 5 milliohms or less | 317 |
| At 2 milliohms or less | 114 |
| At 1 milliohm or less | 58 |
| At 0.5 or 0.75 milliohm | 10 |
| Rated 3 W | 156 |
They come from five series: metal plate, metal plate power, the automotive versions of both, and metal foil, which reaches down into the 0306 and 0612 wide-terminal sizes. Tolerances are 0.5, 1 or 5 percent, and TCR is listed between 50 and 150 ppm/°C. We have not seen the sub-milliohm end of the Walsin range counted this way anywhere else. The full chip resistor range lists every family.
Which Walsin parts cross a 1 milliohm, 2512, 2 W brief?
Five matches in 2512 at 1 percent. We filtered the export to 1 milliohm in 2512 and checked each row against a typical server-supply brief: 1 milliohm, 2512, 1 percent, 2 W or more. Five standard rows match, and the same parts exist in automotive versions.
| Walsin part | Series | Tolerance | TCR (ppm/°C) | Rated power | Current at rated power | Match / mismatch with a 1 milliohm, 2512, 1%, 2 W brief | Your incumbent |
|---|---|---|---|---|---|---|---|
WW25NR001FTL |
Metal plate power | 1% | ≤70 | 2 W | about 45 A | Match | |
WW25KR001FTL |
Metal plate power | 1% | ≤70 | 2 W | about 45 A | Match | |
WW25RR001FTL |
Metal plate power | 1% | ≤75 | 2 W | about 45 A | Match | |
WW25BR001FTL |
Metal plate | 1% | ≤70 | 3 W | about 55 A | Match, more power | |
WW25AR001FTL |
Metal plate power | 1% | ≤70 | 3 W | about 55 A | Match, more power | |
WW25KR001FTLJ |
Metal plate, automotive | 1% | ≤70 | 2 W | about 45 A | Match, automotive grade | |
WW25JR001FTL |
Metal plate | 1% | ≤70 | 1 W | about 32 A | Mismatch: 1 W | |
WW25RR001JTL |
Metal plate power | 5% | ≤75 | 2 W | about 45 A | Mismatch: 5% tolerance | |
WW25AR0L5FTL |
Metal plate power | 1% | ≤70 | 3 W | about 77 A | Mismatch on value: 0.5 milliohm, for higher current |
We worked out the current column ourselves as the square root of rated power over resistance, so it is the current at which the part reaches its rated power under the datasheet’s conditions, not a design limit. Derate it for your board temperature. Confirm against both datasheets and qualify in your own circuit.
What should a UK power team check before it swaps a shunt?
Footprint, power derating and the sense connection. Check that the new part’s pad layout and Kelvin sense points line up with the old footprint, derate rated power for the real copper and ambient temperature, and confirm that TCR and thermal EMF keep the measurement inside your error budget at full load.
Two 2512 metal shunts can share a body size and still differ in pad geometry and in where the true four-terminal sense point sits, and at 1 milliohm a few tenths of a milliohm of copper in the sense path is a large error. Rated power assumes a stated terminal temperature, and a dense AI power shelf in a hot aisle will run warmer, so plan for less than the headline watts. TCR of 70 ppm/°C on a part that rises 60 °C moves the value by about 0.4 percent, which matters if the reading drives a protection threshold. Our post on the 1 milliohm current sense resistor adds the datasheet fields to check.
How do UK buyers get these current sense resistors?
Through a quote, from Hong Kong. The 58 sub-milliohm and 1 milliohm parts above are supplied to order: request a quote and we source them through our authorised Walsin channel, in small lots for prototypes and pilot builds or in reels for production.
Our dated ready-stock list shows what is on our shelf in Hong Kong (snapshot 9 Nov 2026); it is never live-synced. We make no stock, price or lead-time promise; we confirm availability, date code and lead time on each quote. If your BOM also carries thick film sense resistors or MLCC for the same power stage, send them together and we will quote the set.
How Venatech helps
How Venatech helps a UK data centre power team is a current sense resistor cross with power, TCR and tolerance stated. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin; each cross states where the Walsin part differs from your original.
Paste your shunt codes into the cross-reference tool, or upload the whole BOM and request a quote through the site. Check the ready-stock snapshot, dated 9 November 2026. We serve UK teams from Hong Kong, in small lots with fast quotes. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.
The short version
Data Centre Review reported on 12 November 2026 that the UK opened a competition for up to 180 million pounds to host the next national AI supercomputer, targeting 10 MW of IT load by the end of 2027 and 30 MW by March 2029. That power runs through supplies and shelves that sense their own current. Walsin lists 1,188 metal current sense resistors, 58 at 1 milliohm or less, and a 1 milliohm, 2512, 2 W brief returns five standard matches.
Send us your shunt lines with the current and board temperature, and we will return Walsin crosses with every difference stated. Which of your sense positions runs hottest?
Related reading
- Thick film versus metal low-ohm current sense resistors
- Passives for AI server power stages
- The 1 milliohm current sense resistor
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 17 November 2026
Sources
Fetched 17 November 2026.
- Data Centre Review, report on the UK government’s competition for an AI supercomputer data centre, 12 November 2026: https://datacentrereview.com/2026/11/uk-government-offers-180m-for-ai-data-centre-but-theres-a-catch/
- Walsin metal current sense export, Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx, re-measured 17 November 2026; Venatech stock snapshot as at 9 November 2026.
Frequently asked questions
What is the UK’s AI supercomputer data centre competition?
Data Centre Review reported on 12 November 2026 that the UK opened a competition offering up to 180 million pounds for a data centre to host the next national AI supercomputer, with 10 MW of IT load targeted by 31 December 2027 and 30 MW by March 2029.
What does a current sense resistor do in a server power supply?
It turns current into a small voltage that the controller reads, for regulation, load sharing and protection. At AI rack currents the resistance must be around 1 milliohm or less to keep the loss small.
How many 1 milliohm current sense resistors does Walsin offer for UK designs?
We counted 58 Walsin metal current sense part numbers at 1 milliohm or less, and 114 at 2 milliohms or less, in sizes from 0306 to 2512. Venatech crosses and quotes them from Hong Kong for UK teams.
Which Walsin part crosses a 1 milliohm 2512 2 W shunt?
WW25NR001FTL, WW25KR001FTL and WW25RR001FTL match at 1 percent and 2 W; WW25BR001FTL and WW25AR001FTL add power at 3 W. Confirm pad layout and sense points against both datasheets before release.
How much current can a 1 milliohm 2 W resistor carry?
At rated power, about 45 A, from the square root of 2 W over 0.001 ohm. That is at the datasheet’s rated terminal temperature, so derate it for a warm power shelf.
Is Venatech an authorised Walsin distributor?
Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong and serves UK teams in small lots. Stackpole and Viking are lines we supply, not authorised lines.