NEWS

Cyber Resilience Act Reporting in Sweden: Obligations Started on 11 September 2026, and Walsin Lists 142 RF Parts for 2.4 GHz Radios

Cyber Resilience Act reporting has applied to manufacturers since 11 September 2026, and the main obligations follow on 11 December 2027. For a Swedish team re-spinning a 2.4 GHz radio, Walsin Technology (Walsin) lists 142 RF parts for that band, 20 matched to named chipsets. Venatech, the authorised Walsin distributor in Hong Kong, crosses them.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for hardware and RF engineers in Sweden whose products have a radio in them: industrial sensors, smart-building controllers, wearables, telecom accessories. This is perspective, not legal advice. The Cyber Resilience Act (CRA) is mostly a software and process law, but it reaches hardware the moment a team decides to move a product to a newer, better-supported radio chip. That decision changes the passive parts around the antenna, and those are the parts we can cross. We re-measured Walsin’s RF and antenna exports (Venatech_RF_Upload_01.xlsx, 457 part numbers, and Venatech_Antenna_Upload_01.xlsx, 44 part numbers) on 16 November 2026.

What Cyber Resilience Act reporting applies in Sweden from 11 September 2026?

Exploited vulnerabilities and severe incidents. ENISA said on 11 September 2026 that manufacturers’ Cyber Resilience Act reporting obligations apply from that day, covering actively exploited vulnerabilities and severe incidents in products with digital elements, filed once through its new Single Reporting Platform; the CRA’s main requirements apply from 11 December 2027.

The Swedish state research institute RISE wrote on 9 September 2026 that the regulation affects tens of thousands of companies in Sweden, and set out the reporting rhythm: an early notification within 24 hours of becoming aware, a fuller report within 72 hours, and a final report once the incident is resolved. RISE also lists the provisions that follow in December 2027: secure development, vulnerability management, CE marking and compliance documentation. Exactly which of your products are in scope, and what you must file, is a question for your compliance team; we give no legal advice.

Why does the Cyber Resilience Act matter to a hardware team in Sweden?

Because support life now has a deadline attached. Under the Cyber Resilience Act, a manufacturer must handle vulnerabilities across a product’s support period, so a radio chip whose vendor support is thinning becomes a design risk; RISE’s 9 September 2026 note says security must be built in from the earliest development stage and managed across the product lifecycle.

In practice, some Swedish teams will use the run-up to 11 December 2027 to move older Bluetooth, Zigbee or Wi-Fi designs onto a current radio SoC with a maintained software stack. We make no claim about which teams, or which chips. The engineering point is narrower: the balun, band-pass filter and antenna around a 2.4 GHz radio are tuned to that radio’s port impedance. Change the chip and the RF front end has to be checked again, often replaced. Our guide on how to pick a Walsin RF balun covers the method, and the RF range lists every Walsin family.

How many Walsin RF parts cover 2.4 GHz Bluetooth, Wi-Fi and Zigbee?

142 part numbers. We counted 142 distinct Walsin RF parts tagged for 2.4 GHz Bluetooth, Wi-Fi and Zigbee in the RF export: 115 filters, 23 baluns and 4 couplers, from 0605 to 2520, plus 12 chip antennas in the Bluetooth and Wi-Fi band series in the antenna export.

Walsin 2.4 GHz part type Part numbers Case sizes
Filter (band-pass and balun-filter) 115 1005 to 2520
Balun 23 1005, 1608, 2012
Coupler 4 0605, 1608
RF total 142
Chip antenna, Bluetooth and Wi-Fi band 12 3.2 x 1.6 mm to 19 x 3 mm

The 2012 case carries the most filters (64), and 1608 carries the most baluns (11). Our notes on reading an RF filter part number by band and choosing a 2.4 GHz chip antenna explain the codes and the trade-offs.

Which Walsin 2.4 GHz baluns are matched to a named chipset?

Twenty of them. We checked the balanced-port field of all 142 rows and found 20 parts, 3 baluns and 17 balun-filters, where Walsin states a conjugate or impedance match to a named radio chipset, including RFBLN1608060ACT (Nordic nRF24LE1) and RFBPB1608060ABT (TI CC253X, CC254X and CC8520).

Those parts are the ones most exposed to a chip change, because they were designed for one radio. The table sets them against general 50-ohm parts that suit a new SoC with a standard differential port. Put your incumbent in the last column.

Walsin part Type Case Balanced port, from the export Insertion loss (dB) Match / mismatch with a new 2.4 GHz SoC, 50-ohm single-ended, 100-ohm differential Your incumbent
RGBLN1608070A1T Balun 1608 100 ohm 1.5 Match
RFBLN2012080ACT Balun 2012 100 ohm 1.0 Match, larger case, lower loss
RFBLN1005040A7T Balun 1005 50 ohm 0.6 Mismatch on a 100-ohm port; match for a 50-ohm differential port
RFBLN1608060ACT Balun 1608 Conjugate match to Nordic nRF24LE1 2.0 Mismatch unless the new chip is the one named
RFBPB1608060ABT Balun-filter 1608 Conjugate match to TI CC253X, CC254X, CC8520 1.75 Mismatch unless the new chip is one named
RFBPB1510060A0T Balun-filter 1510 Conjugate match to nRF24LE1/AP2, nRF51422, nRF51822 2.5 Mismatch unless the new chip is one named

A chipset-matched part is not wrong; it is specific. If your old design used one and the new SoC’s reference design calls for a 100-ohm differential port, a general part such as RGBLN1608070A1T is the starting point. Confirm against both datasheets and qualify in your own circuit, including a radiated test.

What should change in the RF front end when the radio chip changes?

Three things, checked in order. When a 2.4 GHz radio chip changes, check the balun’s balanced-port impedance against the new chip’s reference design, re-check the band-pass filter’s insertion loss against your link budget, and re-tune the antenna match on the real enclosure; in our 142-row count, port impedance is the field that splits the parts most.

The part number does part of the work. In RFBLN2012080ACT, BLN marks a balun and 2012 the case; in RFBPF1608060AAT, BPF marks a band-pass filter, here with 0.95 dB insertion loss in the export; take final loss and attenuation curves from Walsin’s RF catalogue datasheet, not the export. Keep the old and new RF parts on the same BOM revision record, with lot and date codes, because the CRA’s December 2027 provisions include compliance documentation and your compliance team will want the hardware story to line up with the software one. We supply a certificate of conformity per shipment on request.

How Venatech helps

How Venatech helps is a front-end cross before the re-spin. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, so an old balun, filter and antenna list returns Walsin candidates with every difference stated.

Paste your RF part numbers into the cross-reference tool, or upload the whole radio BOM and request a quote. The RF parts here are to order: we source them through our authorised Walsin channel and confirm availability, date code and lead time on each quote. The ready-stock snapshot, dated 9 November 2026, lists the capacitors and resistors on our shelf in Hong Kong. We serve Stockholm, Gothenburg, Lund and Linkoping from Hong Kong, in small lots. Walsin is our authorised line; Stackpole and Viking are lines we supply. For anything about CRA scope or filings, confirm with your compliance team.

The short version

Cyber Resilience Act reporting of exploited vulnerabilities and severe incidents has applied since 11 September 2026, ENISA says, and the main requirements apply from 11 December 2027. Swedish teams that move a product to a newer radio chip will need to re-check the RF front end. Walsin covers 2.4 GHz with 142 RF parts, 20 of them matched to named chipsets, plus 12 chip antennas.

Send us the balun, filter and antenna from your current radio design, and we will return Walsin crosses for the new chip’s port. Which of your products runs on a radio chip you would not choose today?

Related reading

Last reviewed: 16 November 2026

Sources

Fetched 16 November 2026.

  • ENISA, “The CRA Single Reporting Platform is launched”, 11 September 2026: https://www.enisa.europa.eu/news/the-cra-single-reporting-platform-is-launched
  • RISE Research Institutes of Sweden, “Are companies ready? First CRA requirements take effect in September”, 9 September 2026: https://www.ri.se/en/news/are-companies-ready-first-cra-requirements-take-effect-in-september
  • Walsin RF and antenna exports, Venatech_RF_Upload_01.xlsx and Venatech_Antenna_Upload_01.xlsx, re-measured 16 November 2026; Walsin RF catalogue datasheet linked in the export.

Frequently asked questions

When did Cyber Resilience Act reporting start in Sweden?

ENISA said manufacturers’ reporting obligations for actively exploited vulnerabilities and severe incidents apply from 11 September 2026 across the EU, including Sweden. The CRA’s main requirements apply from 11 December 2027.

What are the CRA reporting deadlines?

RISE describes an early notification within 24 hours of becoming aware, a fuller report within 72 hours and a final report once the incident is resolved. Confirm your own obligations with your compliance team.

Does the Cyber Resilience Act apply to passive components?

The CRA covers products with digital elements; we give no view on scope. A capacitor or balun has no software, but it sits in products that may be in scope, so keep its lot, date code and BOM revision on file.

How many Walsin RF parts cover 2.4 GHz Bluetooth and Wi-Fi?

We counted 142 Walsin RF parts tagged for 2.4 GHz Bluetooth, Wi-Fi and Zigbee: 115 filters, 23 baluns and 4 couplers. There are 12 Walsin chip antennas in the Bluetooth and Wi-Fi band series.

Which Walsin balun suits a new 2.4 GHz chip with a 100-ohm differential port?

General 50-to-100-ohm baluns such as RGBLN1608070A1T in 1608 and RFBLN2012080ACT in 2012. Check the new chip’s reference design, confirm against both datasheets and qualify in your own circuit.

Is Venatech an authorised Walsin distributor for buyers in Sweden?

Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Sweden in small lots. Stackpole and Viking are lines we supply, not authorised lines.


Share This, Choose Your Platform!