NEWS

275V MOV Varistor for Data Centre Power in Thailand: 30,000 MW of Power Requests, a Seven-Tier Framework, and 17 Walsin Varistors at 275 Vac

For an MOV varistor on a data centre power input in Thailand, Walsin Technology (Walsin) lists 17 varistors rated 275 Vac, from 5 mm to 53 mm, and 11 of them are rated 4,500 A or more. Venatech, Walsin’s authorised distributor in Hong Kong, crosses your surge part and quotes the Walsin line.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for an engineer in Thailand designing or buying UPS units, rack power supplies, PDUs, chillers or fan drives for the data centre projects now moving through approval. We parsed Walsin’s varistor export, Venatech_MOV_Upload_01.xlsx (379 distinct part numbers), against Walsin’s MOV_catalog.pdf. The news fact names its source and its date, and every part number below is real.

What did Thailand decide on data centre rules in November 2026?

A seven-tier framework. The Nation reported on 10 November 2026 that Thailand’s Cabinet endorsed a framework that sorts data centres into seven power-use tiers, from below 0.5 MW to over 200 MW, after overlapping power requests from more than 110 applicants reached over 30,000 MW.

The same report says facilities of 0.5 MW or more fall under oversight, projects of 20 MW or more must sit in industrial estates, backup-generator noise is capped at 70 decibels at the boundary, and the Board of Investment had granted promotion to 57 data centre projects as of April, 17 operating and 40 in development. It also says about one quarter of applicants appear to be genuine investors. We add no forecast. For an equipment engineer, the message is that a defined pipeline of real sites is taking shape, and each one will draw UPS, power distribution and cooling hardware.

Why does a data centre in Thailand need MOV varistor protection on every power input?

Because the mains carries surges the electronics cannot. An MOV varistor sits across the line at a power supply, UPS or fan-drive input and clamps a lightning or switching surge to a level the downstream parts survive; Walsin’s catalogue rates its parts for peak surge current from 400 A to 80,000 A.

A large site sees switching transients from its own generators, transfer switches and chillers, as well as surges arriving from the grid. Building-level surge protective devices take the first hit, but each power supply still needs its own board-level clamp, because the energy that passes the panel-level device is still enough to damage a rectifier or a controller. Our guide to how to choose an MOV varistor covers the method, and MOV varistor series selection: D, E, V and industrial explains the four Walsin series. The varistor range lists every part.

What does Walsin cover in MOV varistors at 275 Vac?

Seventeen part numbers across four series. We counted 17 distinct Walsin varistors with a 275 Vac maximum working voltage and a 430 V varistor voltage: six in the Standard D series, three High Energy E, three Super High Energy V and five Industrial, in disc sizes from 5 mm to 53 mm.

275 Vac Walsin varistors by series Part numbers Sizes in the export
Standard (D series) 6 5, 7, 10, 14, 20 and 25 mm
Industrial 5 32, 34 square, 40 and 53 mm
High Energy (E series) 3 5, 7 and 18 mm
Super High Energy (V series) 3 10, 14 and 20 mm
Total 17

Widen the window to 275, 300 and 320 Vac and the count is 51 part numbers, 17 at each voltage. Of the 17 at 275 Vac, 11 carry a peak surge rating of 4,500 A or more. We have not seen the 275 Vac slice of the range laid out this way elsewhere.

Which Walsin varistor fits a 275 Vac, 14 mm, 4,500 A brief?

Four parts, plus two for different jobs. A common board-level brief for a 230 V input is 275 Vac maximum working voltage, a disc near 14 mm and 4,500 A peak; SR431K14D meets it exactly, and SR431K14E keeps the 14 mm size with an 8,000 A rating.

Put your incumbent part in the last column and compare each field.

Walsin part Series Size Max working voltage Peak current Match / mismatch with 275 Vac, about 14 mm, 4,500 A or more Your incumbent
SR431K14D Standard D 14 mm 275 Vac 4,500 A Match
SR431K14E Super High Energy V 14 mm 275 Vac 8,000 A Match, more surge rating at the same size
SR431K20D Standard D 20 mm 275 Vac 6,500 A Match on rating; larger disc, check the footprint
SR431K18E High Energy E 18 mm 275 Vac 9,000 A Match on rating; larger disc
SR431K10D Standard D 10 mm 275 Vac 2,500 A Mismatch: surge rating below 4,500 A
SR391K14D Standard D 14 mm 250 Vac 4,500 A Mismatch: lower working voltage
SR511K14D Standard D 14 mm 320 Vac 4,500 A Mismatch on voltage; fits a 320 Vac brief

For a main input on a large UPS or a three-phase drive, the Industrial SR431K32D, rated 30,000 A at 32 mm, belongs in the conversation. Confirm clamping voltage, energy rating and lead form against both datasheets and qualify in your own circuit.

How should an engineer in Thailand pick between 275 Vac and 320 Vac?

By the worst-case mains, not the nominal. A 275 Vac part leaves about 20 percent headroom over a 230 V supply; a 320 Vac part leaves more for long overvoltage events, at the cost of a higher clamping voltage, so the choice moves stress from the varistor to the parts behind it.

If the site has weak grid sections or long generator runs where the line can sit high for minutes, a 275 Vac part runs warmer and ages faster. A 320 Vac part such as SR511K14D tolerates that, but it lets a higher voltage through to the bridge rectifier and the bulk capacitor, so check their ratings. Pair the varistor with a thermal fuse or a fused design where your safety standard asks for it.

Can Venatech supply these varistors from Hong Kong?

Yes, to order. All 17 Walsin 275 Vac varistors can be quoted from Hong Kong: request a quote and we source them through our authorised Walsin channel, confirming each line on its own quote against our snapshot dated 9 November 2026.

Each quote states availability, date code and lead time for the line, and we work in small lots for prototypes and pilot builds. We make no stock, price or lead-time promise. See the ready-stock list, a dated snapshot, for the capacitors and resistors that sit next to the varistor on the same input board.

How Venatech helps: what should a Thai power team send us?

The surge parts from your BOM. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.

Paste a varistor code into the cross-reference tool, or upload the whole BOM and request a quote through the site. The ready-stock snapshot is dated 9 November 2026. We serve Chonburi, Rayong and Bangkok from Hong Kong, with fast quotes and small lots. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply. We give no compliance advice on Thailand’s data centre rules; confirm that with your own team.

The short version

Thailand’s Cabinet endorsed a seven-tier data centre framework after power requests passed 30,000 MW, The Nation reported on 10 November 2026. Every UPS, power supply and fan drive on those sites needs an MOV varistor at its input. Walsin covers 275 Vac with 17 parts from 5 mm to 53 mm, 11 rated 4,500 A or more, and SR431K14D meets the common 14 mm brief exactly.

Send us your input-stage surge parts and we will return Walsin crosses with every difference stated. Which of your inputs sits on the longest cable run from the switchboard?

Related reading

Last reviewed: 16 November 2026.

Sources

Fetched 16 November 2026.

  • The Nation, “Thailand backs seven-tier framework for data centre projects”, 10 November 2026: https://www.nationthailand.com/news/policy/40073331
  • Walsin varistor export, Venatech_MOV_Upload_01.xlsx, re-measured 16 November 2026; Walsin MOV_catalog.pdf; Venatech Hong Kong stock snapshot dated 9 November 2026.

Frequently asked questions

What is Thailand’s new data centre framework?

The Nation reported on 10 November 2026 that the Cabinet endorsed seven power-use tiers, from below 0.5 MW to over 200 MW. Projects of 20 MW or more must sit in industrial estates, and power requests had passed 30,000 MW.

What MOV varistor voltage suits a 230 V data centre power supply in Thailand?

A 275 Vac maximum working voltage is the common choice for a 230 V input. Choose 320 Vac where the line can sit high for long periods, and check the higher clamping voltage against the parts behind it.

How many Walsin varistors are rated 275 Vac?

We counted 17 in Walsin’s export, in four series from 5 mm to 53 mm. Eleven carry a peak surge rating of 4,500 A or more.

Which Walsin part crosses a 14D431K varistor?

SR431K14D matches a 275 Vac, 14 mm, 4,500 A brief, and SR431K14E keeps the size with 8,000 A. Confirm clamping voltage and energy against both datasheets before release.

Can Venatech supply Walsin varistors to Thailand from Hong Kong?

Yes. Request a quote and we source them through our authorised Walsin channel, with availability, date code and lead time stated on each quote.

Is Venatech an authorised Walsin distributor?

Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong and serves engineers in Thailand in small lots. Stackpole and Viking are lines we supply, not authorised lines.


Share This, Choose Your Platform!