A precision shunt resistor gives a train’s converters and chargers a current reading that holds over heat and years. For rail electronics makers in Switzerland, Walsin lists 322 metal foil shunts from 0.5 milliohm to 0.7 ohm, 266 of them at 50 ppm, against Stackpole CSS briefs. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for hardware engineers and buyers at Swiss makers of rolling stock electronics, auxiliary converters, battery chargers and door and HVAC drives. Walsin Technology (Walsin) is the line we are authorised for; Stackpole Electronics (SEI) is a line we supply, so a CSS already on your parts list can be quoted as it is or crossed to Walsin. We counted the Walsin figures below on 17 November 2026 in our Walsin export Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx, and checked our ready stock snapshot as at 9 November 2026. Stackpole figures come only from Stackpole’s current sensing product page on seielect.com, fetched the same day; the CSS datasheet did not load for us, so confirm each Stackpole figure against it.
What did TPF order from Stadler?
Thirteen four-car Flirt Evo trains for CHF 117 million. Railway News reported on 25 September 2026 that Fribourg operator TPF ordered 13 four-car Stadler Flirt Evo electric multiple units for CHF 117 million, about 125 million euros, as options under the SBB framework tender of 2021, with commercial service from December 2028 and the fleet in service through 2030.
The report gives a maximum speed of 160 km/h, 164 seats and 369 places in total per train, and describes low-energy traction packages. Those are the report’s figures, not ours. Thirteen trains is a modest number; the point for a supplier is the framework behind it, which lets Swiss operators add units, and the long service life of every board fitted to them.
Where does a precision shunt resistor sit on a train?
Wherever a reading must stay accurate for decades. A precision shunt resistor sits in auxiliary converters, battery chargers for the train’s low-voltage supply, door and HVAC motor drives, and energy-metering paths, usually between 0.5 and 20 milliohm, where low TCR keeps the reading stable as the cabinet heats.
Rail boards are expected to run for decades, through wide temperature swings and constant vibration. A metal alloy or metal foil shunt drifts far less with temperature and age than a thick film part, which is why designs that report energy or charge state choose it. The arithmetic still sets the size: a 2 milliohm shunt at 30 A dissipates 1.8 W, within a 2 W 2512 but with no margin, so a lower value or larger case is the better choice. Our low-ohm current sense: thick film vs metal note covers the trade.
How many Walsin metal foil shunts are there?
- We counted 322 distinct Walsin metal foil low-ohm power sensing parts in nine size and power groups from 0306 to 2512, from 0.5 milliohm to 0.7 ohm and 1/3 W to 2 W; 266 are at 50 ppm, and 32 are at 0.5 percent tolerance.
| Walsin metal foil, by size | Rated power (export) | Distinct parts | Best tolerance and TCR (export) |
|---|---|---|---|
| 0306, 0402, 0603 | 1/3 W to 1/2 W | 31 | 1 percent, 50 ppm |
| 0612 | 1 W | 17 | 0.5 percent, 50 ppm |
| 0805 | 1/2 W to 3/4 W | 47 | 0.5 percent, 50 ppm |
| 1206 | 1 W | 97 | 0.5 percent, 50 ppm |
| 1225 | 2 W | 47 | 0.5 percent, 50 ppm (21 parts) |
| 2512 | 2 W | 83 | 0.5 percent, 50 ppm |
Stackpole’s current sensing page, fetched 17 November 2026, describes CSS as an ultra-precision metal alloy current sensing chip resistor in 11 sizes from 0201 to 4527, from 0.2 milliohm to 0.5 ohm, with TCR as low as 15 ppm, at 0.5, 1 or 5 percent, from 0.2 to 5 W, and AEC-Q200. Our export does not give pulse or derating curves, so read those from Walsin’s datasheet. We have not seen this metal foil window counted elsewhere.
Which Walsin parts cross a Stackpole CSS?
Mid-range values in 0603 to 2512 at 50 ppm. For a CSS-style brief from 0.5 milliohm to 0.5 ohm in 0603, 1206 or 2512 at 50 ppm or wider, Walsin has a metal foil part at the same size and value; for 15 ppm, 0.2 milliohm or above 2 W, keep the CSS.
| Your brief (CSS style) | Walsin part | Walsin size, power, tolerance, TCR (export) | Match / mismatch | Your incumbent |
|---|---|---|---|---|
| 10 milliohm, 2512, 0.5 percent | WW25DR010DTL |
2512, 2 W, 0.5 percent, 50 ppm | Match on size, value, tolerance; check TCR | |
| 2 milliohm, 2512 | WW25DR002FTL |
2512, 2 W, 1 percent, 100 ppm | Match on size, value; mismatch on TCR | |
| 5 milliohm, 1206 | WW12DR005FTL |
1206, 1 W, 1 percent, 100 ppm | Match on size, value; mismatch on TCR | |
| 0.1 ohm, 1206 | WW12DR100FTL |
1206, 1 W, 1 percent, 50 ppm | Match on size, value, tolerance | |
| 10 milliohm, 0603 | WW06DR010FTL |
0603, 1/2 W, 1 percent, 50 ppm | Match on size, value, tolerance | |
| Any value at 15 ppm | none in this export | Walsin’s best here is 50 ppm | Mismatch on TCR; keep the CSS, which we can quote | |
| 0.2 milliohm | none in this export | Walsin’s lowest here is 0.5 milliohm | Mismatch on value; keep the CSS |
What should a Swiss rail supplier check before switching?
TCR at your real temperature rise, then the rail test plan. Multiply TCR by the shunt’s expected temperature rise: 50 ppm over a 60 degree rise shifts the reading about 0.3 percent, 100 ppm about 0.6 percent, then decide whether your metering or charge-state budget can carry it.
Then check self-heating at peak current against the derating curve in Walsin’s datasheet, and compare the land pattern and Kelvin sense connection in each datasheet, since metal foil and metal alloy footprints differ. Rail equipment is tested to the operator’s and the standard’s shock, vibration and temperature profiles, and requalification follows the operator’s rules; we give no certification or compliance advice, so confirm with your compliance team. Our qualifying a crossed part: a test plan for QA note sets out the steps.
How Venatech helps
Cross the converter board in one paste. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating size, value, tolerance, TCR and power as match or mismatch.
Paste your shunt lines into the cross-reference tool, or upload the parts list at BOM upload. On our shelf in Hong Kong (snapshot 9 Nov 2026) are three Walsin thick film current sense lines in 0805, WW08WR270FTL, WW08WR390FTL and WW08WR470FTL, for less demanding sensing; see ready stock. The metal foil parts above are not on it, so request a quote and we source them through our authorised Walsin channel. Stackpole CSS lines can be quoted too; Stackpole is a line we supply, and Walsin is the line we are authorised for. We serve Swiss buyers from Hong Kong in small lots and confirm availability, date code and lead time on each quote, with no price, lead-time or stock guarantee. The chip resistor range lists every Walsin family.
The short version
- TPF ordered 13 Stadler Flirt Evo trains for CHF 117 million, entering service from December 2028, per Railway News on 25 September 2026.
- Walsin lists 322 metal foil shunts from 0.5 milliohm to 0.7 ohm; 266 are at 50 ppm and 32 at 0.5 percent.
- A Stackpole CSS brief at 50 ppm or wider in 0603 to 2512 has a Walsin part at the same size and value; at 15 ppm or 0.2 milliohm, keep the CSS.
- Multiply TCR by temperature rise before you approve any cross.
Send us the shunt lines from your converter, charger or drive board, and we will return the Walsin crosses with every difference stated. What TCR does your energy reading actually need?
Related reading
- Low-ohm current sense: thick film vs metal
- What resistor TCR actually buys you
- Qualifying a crossed part: a test plan for QA
- Cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 17 November 2026.
Sources
Fetched 17 November 2026.
- Railway News, “Stadler Secures CHF 117M Order for 13 Swiss Flirt Trains”, 25 September 2026: https://railwaynews.net/stadler-secures-chf-117m-order-for-13-swiss-flirt-trains.html
- Stackpole Electronics current sensing product page: https://seielect.com/products/ProductSearch.asp?keyWord=current+sensing
- Venatech Walsin export (Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx) and ready stock snapshot dated 9 November 2026, re-measured 17 November 2026.
Frequently asked questions
What is a precision shunt resistor used for in Swiss rail electronics?
It measures current in auxiliary converters, low-voltage battery chargers, door and HVAC drives and energy-metering paths, where a low TCR keeps the reading stable as the cabinet heats over a long service life.
How many Walsin metal foil shunts are there?
322 in our export, from 0.5 milliohm to 0.7 ohm in sizes from 0306 to 2512. 266 are at 50 ppm and 32 are at 0.5 percent tolerance.
Which Walsin part crosses a Stackpole CSS at 10 milliohm in 2512?
WW25DR010DTL, a 2512, 10 milliohm, 0.5 percent, 50 ppm, 2 W metal foil part. If your CSS is a 15 ppm part, the TCR does not match; keep it or check whether 50 ppm fits your budget.
Does Walsin have a metal foil shunt at 15 ppm?
Not in this export; the best TCR listed is 50 ppm. For a 15 ppm requirement, keep the Stackpole CSS, which we can quote.
Do you hold precision shunts in stock in Hong Kong?
Not the metal foil parts in the snapshot of 9 Nov 2026. Three Walsin thick film current sense lines in 0805 are on our shelf in Hong Kong; for metal foil, request a quote and we source them through our authorised Walsin channel.
Is Venatech authorised for Stackpole?
No. Venatech is the authorised Walsin distributor in Hong Kong; Stackpole is a line we supply, and we quote Stackpole CSS lines alongside the Walsin cross.