An anti-sulfur resistor keeps working where sulfur in the air would eat a standard chip’s silver terminations. For mining electronics makers in Australia, Walsin lists 2,284 high-power anti-sulfur parts in 0805 and 1206 at 1 percent and 100 ppm, in the sizes of the Stackpole RNCP. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for hardware engineers and buyers at Australian makers and maintainers of mining machine controls, haul truck and charger electronics, conveyor drives and gas-detection equipment. Walsin Technology (Walsin) is the line we are authorised for; Stackpole Electronics (SEI) is a line we supply, so an RNCP already on your parts list can be quoted as it is or crossed to Walsin. We counted the Walsin figures below on 17 November 2026 in our Walsin high-power chip resistor exports, the Thick_Film_High_Power_Chip_Resistor_*.xlsx files, and checked our ready stock snapshot as at 9 November 2026. Stackpole figures come only from Stackpole’s RNCP release of 3 March 2010 on seielect.com, fetched the same day; the RNCP datasheet did not load for us, so confirm each Stackpole figure against it.
What are BHP and Rio Tinto testing in the Pilbara?
Two battery-electric haul trucks at an iron ore mine. BHP said on 23 June 2026 that BHP, Rio Tinto and Caterpillar had launched a trial of two Cat 793 XE Early Learner battery-electric haul trucks at BHP’s Jimblebar iron ore mine in the Pilbara, after three months of on-site testing with more than 100 hours of operation and over 200 test laps.
BHP said Jimblebar hosts two of the seven Early Learner trucks being tested worldwide, that early testing covered high-powered static charging, and that the next phase will test dynamic charging while the trucks move. It also said it remains on track for at least a 30 percent cut in operational greenhouse gas emissions by FY2030 from FY2020 levels. Those are BHP’s statements, not ours. Electrifying a haul fleet adds battery management, traction control and charger electronics to a site that already runs crusher, conveyor and processing controls, and every one of those boards lives in dust, vibration and, near ore processing, sulfur-bearing air.
Why does a mine site need an anti-sulfur resistor?
Because silver and sulfur make silver sulfide, and the resistor goes open. A standard thick film chip has silver in its inner terminations; sulfur compounds in the air react with exposed silver at the edge of the protective coat, and the sulfide grows until the resistor drifts high or opens, often after months in service.
The failure is slow and hard to find in the field, so it hurts most in equipment that is expensive to reach. Sulfur sources around a mine can include ore processing, diesel exhaust, rubber belts and gaskets, and some potting and sealing materials. An anti-sulfur design changes the termination material or adds a barrier so that silver is not exposed. Stackpole’s release of 3 March 2010 says RNCP removes silver from its terminations and is aimed at harsh environments, industrial and off-highway use. Our anti-sulfuration resistors: SF thin film and SA arrays guide covers Walsin’s other sulfur-resistant lines.
How many Walsin anti-sulfur parts are there in 0805 and 1206?
2,284 at 1 percent and 100 ppm. Walsin’s high-power anti-sulfuration thick film family holds 9,135 distinct part numbers from 0402 to 2512; we filtered it to 0805 and 1206 at 1 percent and 100 ppm and counted 2,284, split evenly between the two sizes.
| Walsin high-power anti-sulfur, by size | Rated power (export) | Parts at 1 percent and 100 ppm |
|---|---|---|
| 0402 | 1/8 W | 457 |
| 0603 | 1/8 W | 1,142 |
| 0805 | 1/4 W | 1,142 |
| 1206 | 1/2 W | 1,142 |
| 0805 and 1206 together | 2,284 |
Stackpole’s release of 3 March 2010 describes RNCP as a thin film chip resistor in 0402, 0603, 0805 and 1206, with power from 0.1 to 0.5 W, which it says is twice the rating of standard thick film, maximum working voltage from 50 to 200 V, 1 percent tolerance and 100 ppm TCR. Walsin’s export rates its anti-sulfur 1206 at 1/2 W and 0805 at 1/4 W, within that span; read working voltage from Walsin’s datasheet. We have not seen this window counted elsewhere.
Which Walsin parts cross a Stackpole RNCP?
On size, value, tolerance, TCR and power, with one difference in technology. For an RNCP-style brief at 1 percent and 100 ppm in 0603, 0805 or 1206, Walsin has a high-power anti-sulfur part at the same size and value; the difference is that RNCP is thin film and the Walsin parts are thick film.
| Your brief (RNCP style) | Walsin part | Walsin size, power, tolerance, TCR (export) | Match / mismatch | Your incumbent |
|---|---|---|---|---|
| 10 kilohm, 0805, 1 percent | WF08P1002FTLV |
0805, 1/4 W, 1 percent, 100 ppm | Match on size, value, tolerance, TCR; mismatch on technology | |
| 4.99 kilohm, 0805, 1 percent | WF08P4991FTLV |
0805, 1/4 W, 1 percent, 100 ppm | Match on size, value, tolerance, TCR; mismatch on technology | |
| 100 ohm, 1206, 1 percent | WF12P1000FTLV |
1206, 1/2 W, 1 percent, 100 ppm | Match on size, value, tolerance, TCR; mismatch on technology | |
| 10 ohm, 1206, 1 percent | WF12P10R0FTLV |
1206, 1/2 W, 1 percent, 100 ppm | Match on size, value, tolerance, TCR; mismatch on technology | |
| 1 kilohm, 0603, 1 percent | WF06P1001FTLV |
0603, 1/8 W, 1 percent, 100 ppm | Match on size, value, tolerance, TCR; check power | |
| Working voltage 200 V | any of the above | not stated in our export | Check Walsin’s datasheet |
What should an Australian mining supplier check before switching?
The sulfur test first, then the thin film question. Read each datasheet for the sulfur test method, temperature and hours, check that working voltage covers your circuit, then decide whether a 1 percent, 100 ppm thick film part meets the job your thin film RNCP was doing.
For pull-ups, dividers on a 24 V machine supply and LED drivers, a 1 percent, 100 ppm thick film part usually does the same job. For a precision reference or a low-noise sensor front end, thin film may be the reason the RNCP was chosen, and the cross needs a bench test. A 100 ohm 1206 at 1/2 W also gives you headroom: at 5 V across it, it dissipates 0.25 W, half its rating. Mining equipment follows the site’s and the standard’s own requirements; we give no certification or compliance advice, so confirm with your compliance team. Our thin film vs thick film chip resistors note explains the trade.
How Venatech helps
Cross the sulfur-exposed boards in one paste. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating size, value, tolerance, TCR and power as match or mismatch.
Paste your resistor lines into the cross-reference tool, or upload the parts list at BOM upload. The anti-sulfur parts above are not in our ready stock snapshot of 9 Nov 2026, so request a quote and we source them through our authorised Walsin channel; see ready stock for what is on our shelf in Hong Kong. Stackpole RNCP lines can be quoted too; Stackpole is a line we supply, and Walsin is the line we are authorised for. We serve Australian buyers from Hong Kong in small lots and confirm availability, date code and lead time on each quote, with no price, lead-time or stock guarantee. The chip resistor range lists every Walsin family.
The short version
- BHP, Rio Tinto and Caterpillar are trialling two battery-electric haul trucks at Jimblebar in the Pilbara, per BHP on 23 June 2026.
- Walsin lists 2,284 high-power anti-sulfur parts in 0805 and 1206 at 1 percent and 100 ppm, from a family of 9,135.
- An RNCP brief at 1 percent and 100 ppm has a Walsin part at the same size and value; RNCP is thin film, Walsin’s is thick film.
- Check the sulfur test, working voltage and whether thin film was the reason for the original choice.
Send us the resistor lines from your machine control, charger or gas-detection board, and we will return the Walsin crosses with every difference stated. Which of your boards sits closest to the processing plant?
Related reading
- Anti-sulfuration resistors: SF thin film and SA arrays
- Thin film vs thick film chip resistors
- Chip resistor power rating by case size
- Cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 17 November 2026.
Sources
Fetched 17 November 2026.
- BHP, “BHP, Rio Tinto and Caterpillar launch battery-electric haul truck trial in the Pilbara”, 23 June 2026: https://www.bhp.com/news/media-centre/releases/2026/06/bhp-rio-tinto-and-caterpillar-launch-battery-electric-haul-truck-trial-in-the-pilbara
- Stackpole Electronics release on the RNCP sulfur-resistant chip, 3 March 2010: https://seielect.com/news/20100303_RNCP.htm
- Venatech Walsin high-power chip resistor exports (Thick_Film_High_Power_Chip_Resistor_*.xlsx, anti-sulfuration rows) and ready stock snapshot dated 9 November 2026, re-measured 17 November 2026.
Frequently asked questions
Why do Australian mining electronics need an anti-sulfur resistor?
Sulfur compounds around ore processing, diesel exhaust and some rubber and sealing materials react with the silver in a standard chip resistor’s terminations, and the growing silver sulfide can drive the resistor high or open over months in service.
How many Walsin anti-sulfur resistors are there in 0805 and 1206?
2,284 in our export at 1 percent and 100 ppm, 1,142 in each size, from a high-power anti-sulfuration family of 9,135 distinct parts from 0402 to 2512.
Which Walsin part crosses a Stackpole RNCP at 10 kilohm in 0805?
WF08P1002FTLV, an 0805, 10 kilohm, 1 percent, 100 ppm, 1/4 W anti-sulfur part. It is thick film where RNCP is thin film, so test it if your circuit relies on thin film’s noise or stability.
Is the Walsin part a drop-in match for a thin film RNCP?
It matches on size, value, tolerance, TCR and power, but not on technology. For pull-ups, dividers and LED drivers it usually does the same job; for precision references, run a bench test first.
Do you hold anti-sulfur resistors in stock in Hong Kong?
Not these parts in the snapshot of 9 Nov 2026. Request a quote and we source them through our authorised Walsin channel; the ready stock page lists what is on our shelf in Hong Kong.
Is Venatech authorised for Stackpole?
No. Venatech is the authorised Walsin distributor in Hong Kong; Stackpole is a line we supply, and we quote Stackpole RNCP lines alongside the Walsin cross.