An MOV varistor for home appliances clamps mains surges before they reach the heater relay, motor driver or controller. Walsin lists 34 varistors rated 275 Vac or 300 Vac, 16 of them 5 to 14 mm discs that fit an appliance board. Venatech is the authorised Walsin distributor in Hong Kong, serving Ningbo, China.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for power, EMC and purchasing teams at appliance plants in Ningbo and the wider Zhejiang supply base. Walsin Technology (Walsin) is the line we are authorised for. On 17 November 2026 we parsed every row of our varistor upload file, Venatech_MOV_Upload_01.xlsx (379 distinct part numbers), filtered it to the two working voltages that sit above a 230 V mains, and checked the result against our ready stock snapshot dated 9 November 2026. Every part number below is real and every count is ours.
How big is Ningbo’s home appliance industry?
Big enough to set world share in several product types. China Daily’s Ningbo edition reported on 6 August 2026 that the city is home to more than 3,200 appliance manufacturers and more than 15,000 supporting suppliers, and that one in three household ice makers, heaters and air fryers sold worldwide is made in Ningbo.
The same report covered the 2026 China (Ningbo) International Home Appliance Expo, which opened on 5 August with buyers from 56 countries pre-registered. A separate China Daily Ningbo report of 30 June 2026 said the city’s exports of cooling appliances to Europe, meaning fans, refrigerators, air conditioners and ice makers, reached 2.73 billion yuan from January to May, with fan exports to Europe up 29.3 percent. Those are the newspaper’s figures, not ours. What matters for a design engineer is the product mix: heaters, air fryers, fans and ice makers all switch heating elements or motors straight off the mains, and every one of those boards needs a surge clamp across the input.
Which MOV varistor voltage suits a 230 V home appliance?
Usually 275 Vac or 300 Vac continuous, marked 431 or 471. WorldStandards, updated 7 November 2025, lists China at 230 V and 50 Hz, the same nominal supply as the European market Ningbo exports to; a 275 Vac or 300 Vac varistor leaves 45 V to 70 V of margin above that nominal for mains tolerance and swell.
A metal oxide varistor sits line to neutral, ahead of or just behind the fuse, and conducts hard when the voltage across it rises past its varistor voltage. Choose the continuous working voltage too low and the part runs warm on a high mains, ages and can fail short; choose it too high and the clamping voltage climbs, so the downstream bridge, relay or MOSFET sees more of each surge. Walsin’s three-digit code gives the varistor voltage at 1 mA: 431 is 430 V, 471 is 470 V. Our guide on how to choose an MOV varistor walks through the trade-off step by step.
How many Walsin varistors are rated 275 Vac or 300 Vac?
34, spread across 11 disc sizes. We counted 34 Walsin varistor part numbers rated 275 Vac (code 431) or 300 Vac (code 471): 16 are 5, 7, 10 or 14 mm discs for board mounting, and 18 are 18 mm to 53 mm and 34 mm square parts for heavier surge duty.
| Disc size | Parts at 275 or 300 Vac | Walsin series in the export | Peak current range |
|---|---|---|---|
| 5 mm | 4 | Standard D, High Energy E | 400 A to 800 A |
| 7 mm | 4 | Standard D, High Energy E | 1,200 A to 1,750 A |
| 10 mm | 4 | Standard D, Super High Energy V | 2,500 A to 4,000 A |
| 14 mm | 4 | Standard D, Super High Energy V | 4,500 A to 8,000 A |
| 18 mm to 25 mm | 8 | Standard D, High Energy E, Super High Energy V | 6,500 A to 18,000 A |
| 32 mm to 53 mm, 34 mm square | 10 | Industrial | 30,000 A to 80,000 A |
Each rung has exactly two voltages in this band, 431 and 471, so every board-mount size gives you a choice of margin and surge class without changing footprint. The MOV product range lists all 379 parts, and our note on MOV series selection: D, E, V and Industrial explains what each series letter buys you. We have not seen this 275/300 Vac slice counted anywhere else.
Which Walsin part crosses a 14 mm 471 varistor on an appliance board?
Two parts at 14 mm, and two more one size down. For a 14 mm, 300 Vac, 470 V brief we found SR471K14D at 4,500 A and SR471K14E at 8,000 A peak current; SR471K10D and SR471K10E are the 10 mm options if the board is short of space.
| Brief: 471 varistor, 300 Vac, 10 percent | Walsin part | Size | Peak current in the export | Match / mismatch | Your incumbent |
|---|---|---|---|---|---|
| Same disc, standard surge | SR471K14D |
14 mm | 4,500 A | Match on voltage and size | |
| Same disc, higher surge | SR471K14E |
14 mm | 8,000 A | Match, higher surge class | |
| Smaller disc, standard | SR471K10D |
10 mm | 2,500 A | Mismatch on size and surge: check your test level | |
| Smaller disc, higher surge | SR471K10E |
10 mm | 4,000 A | Mismatch on size; surge sits between the two 14 mm parts | |
| Lower margin, same disc | SR431K14D |
14 mm | 4,500 A | Mismatch on voltage: 275 Vac, lower clamp | |
| Heater or fan board, compact | SR471K07D |
7 mm | 1,200 A | Mismatch, for low surge levels only |
Fill in the last column with your current part, then compare lead spacing, lead form, disc thickness and the clamping voltage at your surge current against Walsin’s MOV_catalog.pdf. A generic marking such as 14D471K usually describes the same voltage and size, but the energy rating and approvals differ between makers, so treat it as a starting point. For heavier duty, MOV energy ratings: 40,000 A versus 80,000 A covers the industrial parts.
Is a Walsin varistor on the Hong Kong shelf?
Not this week, but the mains filter still has a stocked part. We checked all 379 Walsin varistors against our snapshot of 9 November 2026: none is on it, while one S2 X1/Y2 safety chip capacitor, S252B222K502 at 2,200 pF, is on our shelf in Hong Kong (snapshot 9 Nov 2026).
For the varistors, request a quote and we source them through our authorised Walsin channel, confirming date code and lead time on each quote. The S2 chip is not a varistor; it is the Y capacitor that often sits on the same mains input, so it can ride on the same order. The ready stock list is a dated snapshot held in Hong Kong. We give no stock or lead-time promise.
How Venatech helps: what can we cross for a Ningbo appliance board?
The whole input stage, in one upload. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, and we quote small lots to Ningbo from Hong Kong.
Paste your varistor, Y capacitor and resistor lines into the cross-reference tool, or upload the full bill of materials at /bom/, and request a quote through the site. Every difference from your original part is stated: voltage code, disc size, surge class and approvals. Hong Kong-based service means one quote covers the Walsin lines and the passives around them. Certification of the finished appliance stays with you and your test house.
The short version
- Ningbo has more than 3,200 appliance makers and 15,000 suppliers, and makes one in three ice makers, heaters and air fryers sold worldwide (China Daily Ningbo, 6 August 2026).
- China is listed at 230 V, 50 Hz (WorldStandards, 7 November 2025); 275 Vac and 300 Vac varistors sit above it.
- Walsin lists 34 varistors at 275 or 300 Vac, 16 of them 5 to 14 mm board-mount discs.
- A 14 mm 471 brief returns SR471K14D and SR471K14E.
- No varistor is on our shelf this week; one S2 safety chip is (snapshot 9 Nov 2026).
We will not call a part a drop-in match. We will show you where it differs. Which surge level does your appliance standard ask the input stage to pass?
Related reading
- How to choose an MOV varistor
- MOV series selection: D, E, V and Industrial
- MOV energy ratings: 40,000 A versus 80,000 A
- Free cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 17 November 2026.
Sources
Fetched 17 November 2026.
- China Daily Ningbo, Ningbo Home Appliance Expo attracts global buyers, 6 August 2026: https://ningbo.chinadaily.com.cn/2026-08/06/c_1202914.htm
- China Daily Ningbo, Ningbo cooling appliances see export boom amid Europe’s heatwave, 30 June 2026: https://ningbo.chinadaily.com.cn/2026-06/30/c_1194015.htm
- WorldStandards, China plug and voltage page, updated 7 November 2025: https://www.worldstandards.eu/electricity/plug-voltage-by-country/china/
- Venatech varistor upload file Venatech_MOV_Upload_01.xlsx, Walsin MOV_catalog.pdf and ready stock snapshot dated 9 November 2026, re-measured 17 November 2026.
Frequently asked questions
What does an MOV varistor do in a home appliance?
It sits across the mains input and conducts when a surge pushes the voltage past its varistor voltage, absorbing the energy so the relay, heater driver or controller does not have to.
What MOV varistor voltage should a 230 V appliance in China use?
Most designs use 275 Vac (code 431) or 300 Vac (code 471) continuous. The exact choice depends on your mains tolerance, surge test level and standard; confirm it with your compliance team.
How many Walsin varistors are rated 275 Vac or 300 Vac?
34 in our count of 17 November 2026, across 11 sizes from 5 mm to 53 mm, with 16 of them in the 5, 7, 10 and 14 mm board-mount discs.
Which Walsin part crosses a 14D471K varistor?
SR471K14D at 4,500 A or SR471K14E at 8,000 A peak current, both 14 mm and 300 Vac. Check lead spacing, thickness and clamping voltage against both datasheets.
Does Venatech stock Walsin varistors in Hong Kong?
None is on our snapshot of 9 November 2026. Varistors are sourced on request through our authorised Walsin channel, with date code and lead time confirmed on each quote.
Can Venatech supply appliance makers in Ningbo, China?
Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Ningbo. Use the free cross-reference tool or upload a BOM; confirm import rules with your compliance team.