For a chip resistor array on a board built in Germany, Walsin Technology (Walsin) lists 10,022 array part numbers, 1,386 of them automotive and 2,772 anti-sulfuration, and a 10 kilohm, 1 percent brief returns 18. Venatech, Walsin’s authorised distributor in Hong Kong, crosses and quotes them for German teams.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for a hardware, layout or purchasing engineer in Germany who wants fewer placements on a dense board, or a second source for an array already in production. We parsed Walsin’s two array exports, Thick_Film_Chip_Resistor_Array__1of1.xlsx and Thick_Film_Chip_Resistor_Array_Anti_Sulfuration__1of1.xlsx, and our stock snapshot as at 9 November 2026. The news was fetched on 17 November 2026.
What did electronica 2026 show about the electronics industry in Germany?
A busy show and rising orders. eeNews Europe reported on 16 November 2026 that electronica 2026 in Munich, which closed on 13 November, drew more than 86,000 visitors from 107 countries and regions and 3,512 exhibitors from 60, and that, citing ZVEI, new orders rose by almost 13 percent between January and September 2026.
The same report says 74 percent of exhibitors and 54 percent of visitors came from outside Germany, that artificial intelligence dominated many discussions, from smart sensors to automated manufacturing, and that edge computing, energy efficiency and cybersecurity were prominent. We take two things from that for a German hardware team. Orders are moving again, so second-source and BOM work that waited through a slow year is back on the list. And the edge and sensor boards on show are exactly the dense, connector-heavy designs where a resistor array saves the most placements.
Why do German board designers use a chip resistor array?
To place one part where four would go. A chip resistor array packs two, four or eight resistors into one body, so a single 4-element array replaces four discrete chips on pull-ups, pull-downs, bus termination, LED current setting and address straps, cutting placements, feeder slots and board area at the same time.
That matters most on the boards that filled the halls in Munich: edge controllers, sensor hubs and industrial I/O, where a single connector or bus can need eight or sixteen identical resistors. An array also gives matched values from one print, which helps where several lines must behave alike. The trade-offs are flexibility and repair: every element shares one value, and a single failed element means replacing the whole part. Our note on chip resistor arrays explained covers the basics, and resistor arrays versus discrete sets out when discrete chips still win.
How many chip resistor arrays does Walsin list?
10,022 part numbers, across 18 series. We counted 10,022 distinct array part numbers in Walsin’s two exports: 7,250 in the standard range and 2,772 in the anti-sulfuration range. 7,741 are at 1 percent, and 1,386 sit in the two automotive series.
| Walsin chip resistor arrays, measured 17 Nov 2026 | Part numbers |
|---|---|
| All array part numbers | 10,022 |
| Built on 0603 elements (2- and 4-element) | 5,076 |
| Built on 0402 elements (2- and 4-element) | 4,003 |
| 8-element, 0602 body | 555 |
| 0201 flat, 2- and 4-element | 388 |
| At 1 percent | 7,741 |
| Anti-sulfuration | 2,772 |
| Automotive series | 1,386 |
| At 10 kilohm, 1 percent | 18 |
Rated power is 1/32 W, 1/16 W or 1/10 W per element, and the tightest TCR listed is ±100 ppm/°C, held by 571 parts. Convex, concave and flat terminal types are all listed. We have not seen the Walsin array range split this way elsewhere. The full chip resistor range lists every family.
Which Walsin arrays cross a 10 kilohm, 4-element, 0603 brief?
Four clean matches, and four that differ in one field. We filtered both exports to 10 kilohm at 1 percent and found 18 part numbers. Against a typical pull-up brief, 10 kilohm, 4 elements on 0603, convex terminals, 1 percent, 1/10 W, four rows match; the rest miss on terminal type, element count or size.
| Walsin part | Series | Elements and size | Terminals | TCR (ppm/°C) | Power per element | Match / mismatch with a 10 kilohm, 4 x 0603, convex, 1% brief | Your incumbent |
|---|---|---|---|---|---|---|---|
WA06X1002FTL |
Standard | 4 x 0603 | Convex | ±100 | 1/10 W | Match, tightest TCR | |
WA06X1002FTLJ |
Standard | 4 x 0603 | Convex | ±200 | 1/10 W | Match | |
MA06X1002FTL |
Automotive | 4 x 0603 | Convex | ±200 | 1/10 W | Match, automotive series | |
SA06X1002FTL |
Anti-sulfuration | 4 x 0603 | Convex | ±200 | 1/10 W | Match, for sulfur-laden air | |
WA06T1002FTL |
Standard | 4 x 0603 | Concave | ±200 | 1/16 W | Mismatch: concave footprint, lower power | |
WA04X1002FTL |
Standard | 4 x 0402 | Convex | ±200 | 1/16 W | Mismatch: smaller element size | |
WA06Y1002FTL |
Standard | 2 x 0603 | Convex | ±200 | 1/10 W | Mismatch: 2 elements | |
WA06W1002FTL |
Standard | 8 x 0602 body | Convex | ±200 | 1/16 W | Mismatch: 8 elements |
For a board that sees industrial or engine-bay air, SA06X1002FTL and MA06X1002FTL are the ones to qualify first. Confirm against both datasheets and qualify in your own circuit.
What should a German team check before it swaps a resistor array?
Footprint, circuit and environment. Check that terminal type and pitch match the land pattern, since convex and concave arrays do not share one, confirm that the internal circuit is the same isolated or bussed arrangement as your incumbent, and match the environment, from TCR to sulfur exposure.
The footprint is the most common trap: a convex array and a concave array of the same size and value need different pads, and an 8-element array is a different part altogether. The internal circuit is the second: arrays with a common bus and arrays with isolated elements can share a body but not a schematic, so read the circuit drawing on both datasheets. Then the environment. A control cabinet near rubber, diesel or a paper mill can carry enough sulfur to attack silver terminations, which is what the anti-sulfuration series is for; our note on anti-sulfuration resistors and SA arrays explains the mechanism. For automotive work, take the qualification documents from Walsin’s datasheet rather than the series name.
How do German buyers get Walsin resistor arrays?
Through a quote, from Hong Kong. The 18 arrays at 10 kilohm, 1 percent, and the rest of the 10,022, are supplied to order: request a quote and we source them through our authorised Walsin channel, in small lots for prototypes or in reels for production.
Our dated ready-stock list shows what is on our shelf in Hong Kong (snapshot 9 Nov 2026); it is never live-synced. If a prototype cannot wait for arrays, discrete chips at the same value can stand in while the array is on order. We make no stock, price or lead-time promise; we confirm availability, date code and lead time on each quote.
How Venatech helps
How Venatech helps an electronics maker in Germany is a chip resistor array cross with terminal type and circuit stated. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin; each cross states where the Walsin part differs from your original.
Paste your array codes into the cross-reference tool, or upload the whole BOM and request a quote through the site. Check the ready-stock snapshot, dated 9 November 2026. We serve German teams from Hong Kong, in small lots with fast quotes. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.
The short version
eeNews Europe reported on 16 November 2026 that electronica 2026 drew 3,512 exhibitors and more than 86,000 visitors to Munich, and that ZVEI saw new orders up almost 13 percent in the first nine months of 2026. The dense edge and sensor boards on show are where arrays pay off. Walsin lists 10,022 chip resistor array part numbers, and a 10 kilohm, 4-element, 0603 brief returns four clean matches, including automotive and anti-sulfuration options.
Send us your array and discrete resistor lines, and we will return Walsin crosses with every difference stated. Which bus on your board still uses eight discrete pull-ups?
Related reading
- Chip resistor arrays explained
- Resistor arrays versus discrete resistors
- Anti-sulfuration resistors: SF thin film and SA arrays
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 17 November 2026
Sources
Fetched 17 November 2026.
- eeNews Europe, report on electronica 2026 visitor and exhibitor figures, 16 November 2026: https://www.eenewseurope.com/en/electronica-2026
- Walsin array exports, Thick_Film_Chip_Resistor_Array__1of1.xlsx and Thick_Film_Chip_Resistor_Array_Anti_Sulfuration__1of1.xlsx, re-measured 17 November 2026; Venatech stock snapshot as at 9 November 2026.
Frequently asked questions
What were the electronica 2026 figures?
eeNews Europe reported on 16 November 2026 that electronica 2026 in Munich drew more than 86,000 visitors from 107 countries and regions and 3,512 exhibitors from 60, and that, citing ZVEI, new orders rose by almost 13 percent from January to September 2026.
What is a chip resistor array used for?
Pull-ups, pull-downs, bus termination, LED current setting and address straps, wherever several resistors share one value. A 4-element array replaces four discrete chips, which saves placements and board area.
How many chip resistor arrays does Walsin offer for German designs?
We counted 10,022 Walsin array part numbers, including 1,386 automotive and 2,772 anti-sulfuration parts, from 0201 flat arrays to 8-element types. Venatech crosses and quotes them from Hong Kong for teams in Germany.
Which Walsin array crosses a 10 kilohm 4-element 0603 convex array?
WA06X1002FTL is the closest standard match at ±100 ppm/°C. MA06X1002FTL is the automotive option and SA06X1002FTL the anti-sulfuration option. Confirm footprint and internal circuit against both datasheets before release.
Can a concave resistor array replace a convex one?
Not on the same land pattern. Convex and concave arrays of the same size and value use different pads, so a swap needs a footprint change. Match the terminal type first, then the value.
Is Venatech an authorised Walsin distributor?
Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong and serves teams in Germany in small lots. Stackpole and Viking are lines we supply, not authorised lines.