An AEC-Q200 soft termination MLCC puts a flexible conductive layer under the plating so board bending cracks the termination, not the ceramic. Walsin’s ST series lists 116 such parts, 34 of them in 0603, reaching 22 uF in 1210. Venatech is the authorised Walsin distributor in Hong Kong, serving Pitesti, Romania.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for electronics engineers and buyers at the supplier base around Pitesti and Mioveni in Arges county. Walsin Technology (Walsin) is the line we are authorised for. On 16 November 2026 we filtered our MLCC upload files, Venatech_MLCC_Upload_01.xlsx to Venatech_MLCC_Upload_08.xlsx (23,360 distinct part numbers), to Walsin’s automotive soft-termination ST series and compared it with the AEC-Q200 MT series and the commercial SH soft-termination series. Every part number below is in Walsin’s export.
What does Dacia build at Mioveni, next to Pitesti?
The Duster and the Bigster. Agerpres reported on 9 September 2026, in an analysis of a report by the AEI think tank, that the current-generation Duster entered production at Mioveni at the end of 2023 and that the Bigster has been built only at Mioveni since 2025.
The same analysis frames 2027 to 2029 as the window in which Renault decides where the next-generation Duster is built, and says Dacia is not on the verge of closing the plant. For a supplier engineer near Pitesti, that timeline matters for one reason: a new vehicle generation usually means new electronic modules, and new modules are when the capacitor list is opened, qualified and second-sourced. We draw no conclusion about volumes; that is the AEI’s analysis, not ours.
Why do car electronics boards use an AEC-Q200 soft termination MLCC?
Because flex cracking is a mechanical failure the circuit cannot see until it shorts. A ceramic capacitor is stiff, and when a populated board bends during depaneling, screw-down, connector insertion or vibration, the stress concentrates at the termination; a crack there can open or, worse, leak and short. A soft termination layer absorbs that strain.
Large case sizes near board edges, screw bosses and connectors carry the highest risk, and battery-connected capacitors carry the highest consequence, since a shorted part there sits across a live supply. AEC-Q200 is the automotive stress-test qualification for passive parts; Walsin describes the ST series as qualified to AEC-Q200, and the word is qualified, not certified. Soft termination does not replace good layout: keep large MLCC parallel to the bend axis and away from mounting points. Our post on flex cracking and board bend explains the mechanism, and what AEC-Q200 actually certifies explains the test groups.
How many AEC-Q200 soft termination MLCC does Walsin list?
- We counted 116 Walsin ST series part numbers, against 2,167 in the AEC-Q200 MT series without soft termination; X7R makes up 113 of the 116, and the range runs from one 0402 part to five in 2220.
| Case size | ST parts | Highest capacitance | Rated voltages in the export |
|---|---|---|---|
| 0402 | 1 | 100 nF | 16 V |
| 0603 | 34 | 220 nF | 16 V to 100 V |
| 0805 | 24 | 1 uF | 25 V to 100 V |
| 1206 | 27 | 10 uF | 16 V to 1,000 V |
| 1210 | 22 | 22 uF | 10 V to 1,250 V |
| 1812 | 1 | 100 pF | 3,000 V |
| 1825 | 2 | 100 nF | 1,000 V |
| 2220 | 5 | 10 uF | 100 V to 3,000 V |
The 0603 row is the working core for body, lighting and sensor modules: 19 of its 34 parts are rated 50 V and 8 are rated 100 V. At the other end, 17 ST parts are rated 630 V or more, among them ST31B472K102 at 4.7 nF and 1,000 V in 1206 and ST55B103K302 at 10 nF and 3,000 V in 2220. By tolerance the 116 split 62 at 10 percent, 28 at 20 percent and 26 at 5 percent. Walsin’s MLCC catalogue datasheet covers the series; the MLCC range page shows every family.
Which Walsin parts answer a 100 nF, 0603, 50 V soft termination brief?
Two in ST, plus four near neighbours. For 100 nF, X7R, 0603 at 50 V with soft termination and AEC-Q200, we found two Walsin ST parts, ST18B104K500 at 10 percent and ST18B104M500 at 20 percent; the 100 V ST18B104K101 and the AEC-Q200 MT part without soft termination are the next options.
| Brief: 100 nF, X7R, 0603, 50 V, soft termination, AEC-Q200 | Walsin part | Series | Tolerance | Match / mismatch | Your incumbent |
|---|---|---|---|---|---|
| Exact | ST18B104K500 |
ST, AEC-Q200 soft termination | 10% | Match | |
| Wider tolerance | ST18B104M500 |
ST | 20% | Mismatch in tolerance | |
| Higher voltage | ST18B104K101 |
ST | 10% | Match, rated 100 V: more margin, check bias curve | |
| Lower voltage | ST18B104K250 |
ST | 10% | Mismatch: 25 V only | |
| No soft termination | MT18B104K500 |
MT, AEC-Q200 | 10% | Mismatch: standard termination | |
| Not automotive-qualified | SH18B104K500 |
SH, commercial soft termination | 10% | Mismatch: not AEC-Q200 |
Leave the last column for your current part and compare thickness as well as value: the ST18 rows print a thickness of 0.80 plus or minus 0.30 mm at 50 V, wider than the 0.80 plus or minus 0.07 mm on the 25 V row, which matters for pick-and-place and for any height limit. Our post on soft termination MLCC: SH, SG, ST and VT compares the families.
What is on the Hong Kong shelf for a Pitesti line?
A commercial soft-termination part, not an automotive one. We checked all 116 ST parts and 2,167 MT parts against our snapshot of 9 November 2026: none is on it, while 29 commercial SH soft-termination lines are, including SH18B104K500 at 100 nF and 50 V, on our shelf in Hong Kong (snapshot 9 Nov 2026).
That SH part suits prototypes, test fixtures and non-automotive builds; it is not a substitute in a PPAP-controlled design, because it is not qualified to AEC-Q200. ST and MT lines are to order: request a quote and we source them through our authorised Walsin channel, confirming date code and lead time on each quote. The ready stock list is a dated snapshot held in Hong Kong. We give no stock or lead-time promise.
How Venatech helps: what can we cross for a Pitesti supplier?
A module’s MLCC list, grade by grade. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, with a filter for automotive grade and for soft termination.
Paste the capacitor lines into the cross-reference tool and set the grade filter to automotive: commercial parts are shown first with the AEC-Q200 version listed beneath where one exists. For a full module, upload the BOM at /bom/ and request a quote. We supply small lots from Hong Kong, with lot and date-code traceability and a certificate of conformity per shipment on request. Qualification and PPAP stay with you.
The short version
- The Bigster has been built only at Mioveni since 2025; the next-generation Duster decision window is 2027 to 2029 (Agerpres, AEI analysis, 9 September 2026).
- Walsin’s ST series lists 116 AEC-Q200 soft termination MLCC, against 2,167 in the MT series.
- 34 ST parts are 0603; the series reaches 10 uF in 1206 and 22 uF in 1210.
- A 100 nF, 0603, 50 V brief returns two ST parts.
- No ST or MT part is on our shelf in Hong Kong (snapshot 9 Nov 2026); 29 commercial SH lines are.
We will not tell you a part is a drop-in match. We will show you where it differs. On your Mioveni-bound modules, which capacitors sit within 5 mm of a screw boss?
Related reading
- Flex cracking and board bend: why soft termination exists
- AEC-Q200 MLCC: MT versus MG series
- Soft termination MLCC in Germany: SG and SH against automotive ST
- Free cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 16 November 2026.
Sources
Fetched 16 November 2026.
- Agerpres, AEI: Dacia not closing Mioveni plant, but Romania could gradually lose production volumes, 9 September 2026: https://agerpres.ro/english/2026/09/09/aei-dacia-not-closing-mioveni-plant-but-romania-could-gradually-lose-production-volumes-analysis–1591938
- Venatech MLCC upload files Venatech_MLCC_Upload_01.xlsx to _08.xlsx and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.
Frequently asked questions
What is an AEC-Q200 soft termination MLCC?
A multilayer ceramic capacitor qualified to the AEC-Q200 automotive stress tests, with a flexible conductive layer in its terminations that absorbs board bending. Walsin’s version is the ST series.
How many AEC-Q200 soft termination MLCC does Walsin make?
116 in our count of 16 November 2026, from 0402 to 2220, 113 of them X7R, against 2,167 parts in the AEC-Q200 MT series with standard termination.
Which Walsin part crosses a 100 nF 0603 50 V soft termination MLCC?
ST18B104K500 at 10 percent, or ST18B104M500 at 20 percent. ST18B104K101 is rated 100 V. Confirm thickness and the DC bias curve against both datasheets.
Is the SH series qualified to AEC-Q200?
No. SH is Walsin’s commercial soft-termination series. For an automotive design in Romania, use ST, and check that your customer’s PPAP accepts the part.
Does Venatech stock automotive MLCC in Hong Kong?
No ST or MT part is on our snapshot of 9 November 2026. Commercial SH lines such as SH18B104K500 are. Automotive lines are sourced on request through our authorised Walsin channel.
Can Venatech supply automotive suppliers in Pitesti, Romania?
Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Romania. Use the free cross-reference tool or upload a BOM; confirm import rules with your compliance team.