NEWS

High Temperature MLCC for Defence and Engine Electronics in Gebze, Turkey: 128 Walsin HT Parts Rated to 150°C

A high temperature MLCC is rated to 150°C instead of the usual 125°C, which is the margin engine-mounted, power and down-hole electronics need. Walsin’s HT series lists 128 such parts, 102 in X8G and 26 in X8R, from 0402 to 1210. Venatech is the authorised Walsin distributor in Hong Kong, serving Gebze, Turkey.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for engineers and buyers in Gebze’s defence, aerospace and automotive supplier base and across Kocaeli. Walsin Technology (Walsin) is the line we are authorised for. On 16 November 2026 we filtered our MLCC upload files, Venatech_MLCC_Upload_01.xlsx to Venatech_MLCC_Upload_08.xlsx (23,360 distinct part numbers), to an operating range reaching 150°C and checked the result against our ready stock snapshot dated 9 November 2026. All part numbers below are real.

What did TRMOTOR open in Gebze?

A subsystem test centre for its national engines. Memurlar.net, carrying Anadolu Agency, reported on 25 June 2026 that TRMOTOR opened its Subsystems Test Centre on the Gebze Technical University campus, with four rigs to verify parts of the TF35000 engine and an auxiliary power unit, including the TF35000 fuel metering unit.

The four rigs cover an air turbine starter overrun test, the TF35000 air-oil separator, the fuel metering unit’s response to changes in flow and pressure, and an auxiliary power unit gearbox under load, temperature and durability conditions. The report says the centre aims to reduce dependence on foreign suppliers for engine technology and to give students hands-on experience. The figures are TRMOTOR’s as reported. For electronics engineers around Gebze, an engine programme moving into test means sensor, actuator-drive and data-acquisition boards that sit close to heat, and their capacitor lists get read against temperature first.

When does an engine or defence board need a high temperature MLCC?

When the ceramic sees more than 125°C, from ambient plus self-heating. Most Class II MLCC such as X7R are rated to 125°C; boards near engines, gearboxes, power modules or exhaust paths, and sealed housings in the sun, can exceed that, so designers move to a 150°C dielectric: X8R for capacitance, X8G for stability.

X8R is the 150°C counterpart of X7R, a Class II dielectric that trades stability for capacitance per volume. X8G is a Class I dielectric that holds its value closely across temperature, the choice for timing, filtering and sensor signal paths where drift is an error. Both lose life faster as temperature rises, so the rating is a ceiling, not a target: derate voltage at the upper end of the range and check how many hours the part sees there. Our post on high temperature MLCC to 150°C: the HT series covers the series in depth, and NP0 versus X7R versus X5R explains the dielectric classes.

How many 150°C MLCC does Walsin list, and in which dielectrics?

235, of which 128 are in the HT series. We counted 235 Walsin MLCC with an operating range reaching 150°C: 128 in the High Temperature HT series, 104 X8G parts in the microwave RF series, and three 18 pF X8G parts in the AEC-Q200 MT series.

HT case size X8G parts X8R parts Highest X8G Highest X8R Rated voltages
0402 7 0 470 pF none 50 V
0603 23 8 3.3 nF 10 nF 50 V, 100 V
0805 28 9 10 nF 47 nF 50 V, 100 V
1206 24 9 10 nF 100 nF 50 V, 100 V
1210 20 0 15 nF none 50 V
Total 102 26

The HT series runs at 50 V and 100 V only, 61 parts at 50 V and 67 at 100 V, and X8R stops at 100 nF in 1206, HT31R104K500. By tolerance the 128 split 78 at 5 percent, 30 at 10 percent and 20 at plus or minus 0.1 pF for the smallest values. For capacitance above that ceiling at 150°C, a design usually parallels parts or moves the bulk capacitor to a cooler spot on the board. Walsin’s own HT datasheet, WTC_MLCC_High_Temperature_HT.pdf, covers the series, and the MLCC range page shows every family.

Which Walsin parts answer a 10 nF, 150°C MLCC brief?

Six, in four sizes. For 10 nF rated to 150°C, we found six Walsin HT parts: three X8R at 10 percent and 50 V in 0603, 0805 and 1206, and three X8G at 5 percent, in 0805 and 1210 at 50 V and in 1206 at 100 V.

Brief: 10 nF, 150°C, 50 V or more Walsin part Size Dielectric Voltage Match / mismatch Your incumbent
Smallest body HT18R103K500 0603 X8R, 10% 50 V Match for a Class II brief
0805, Class II HT21R103K500 0805 X8R, 10% 50 V Match
1206, Class II HT31R103K500 1206 X8R, 10% 50 V Match
0805, stable HT21G103J500 0805 X8G, 5% 50 V Match; Class I, tighter value
1206, higher voltage HT31G103J101 1206 X8G, 5% 100 V Match, more voltage margin
1210, stable HT32G103J500 1210 X8G, 5% 50 V Mismatch on footprint: 1210

Leave the last column for your current part. An X8R part is the natural cross for an X7R incumbent that has run out of temperature margin, but the footprint and the capacitance at bias still need checking; an X8G part replaces a C0G where the value must not move. Our post on how to cross-reference an MLCC lists which fields to check first.

Which Walsin 150°C MLCC are on the Hong Kong shelf?

Three. We checked all 235 Walsin MLCC rated to 150°C against our snapshot of 9 November 2026: three are on our shelf in Hong Kong (snapshot 9 Nov 2026), the HT parts HT21G331K500 at 330 pF and HT21G472K500 at 4.7 nF, both 0805 X8G at 50 V, and the RF series RF21G8R2C251 at 8.2 pF and 250 V.

Those three suit rig builds, prototypes and repair. Lines not on the snapshot are to order: request a quote and we source them through our authorised Walsin channel, confirming date code and lead time on each quote. The ready stock list is a dated snapshot held in Hong Kong. We give no stock or lead-time promise.

How Venatech helps: what can we cross for a Gebze engineering team?

The hot end of the board, part by part. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, with a filter for high temperature parts.

Paste the capacitor lines into the cross-reference tool and set the special-requirement filter to high temperature, or upload the BOM at /bom/ and request a quote. Every difference from your original is stated. We supply Turkey from Hong Kong in small lots, with lot and date-code traceability and a certificate of conformity per shipment on request. Qualification and any end-use paperwork stay with you.

The short version

  • TRMOTOR opened a subsystems test centre for the TF35000 engine on the Gebze Technical University campus (Memurlar.net via Anadolu Agency, 25 June 2026).
  • Walsin lists 235 MLCC rated to 150°C, 128 of them in the HT series.
  • HT splits 102 X8G and 26 X8R, from 0402 to 1210, at 50 V and 100 V.
  • A 10 nF, 150°C brief returns six HT parts.
  • Three Walsin 150°C MLCC are on our shelf in Hong Kong (snapshot 9 Nov 2026).

We will not tell you a part is a drop-in match. We will show you where it differs. What is the hottest board temperature your Gebze rig logs, and for how many hours?

Related reading

Last reviewed: 16 November 2026.

Sources

Fetched 16 November 2026.

  • Memurlar.net (Anadolu Agency), Milli motorlarin kritik alt sistemleri Gebze’de test edilecek, 25 June 2026: https://www.memurlar.net/haber/1171124/milli-motorlarin-kritik-alt-sistemleri-gebze-de-test-edilecek.html
  • Venatech MLCC upload files Venatech_MLCC_Upload_01.xlsx to _08.xlsx and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.

Frequently asked questions

What is a high temperature MLCC?

A multilayer ceramic capacitor rated to operate above the usual 125°C. Walsin’s HT series is rated from minus 55°C to 150°C, in X8G and X8R dielectrics.

How many 150°C MLCC does Walsin make?

235 in our count of 16 November 2026: 128 in the HT series, 104 X8G parts in the RF series and three in the AEC-Q200 MT series.

What is the difference between X8R and X8G?

X8R is a Class II dielectric, the 150°C counterpart of X7R, with more capacitance per size. X8G is a Class I dielectric that holds its value closely, like C0G.

Which Walsin part crosses a 10 nF 150°C MLCC?

HT18R103K500 in 0603, HT21R103K500 in 0805 or HT31R103K500 in 1206 in X8R; HT21G103J500 or HT31G103J101 in X8G. Check footprint and bias behaviour against both datasheets.

Does Venatech stock 150°C MLCC in Hong Kong?

Three lines are on our snapshot of 9 November 2026: HT21G331K500, HT21G472K500 and RF21G8R2C251. Other lines are sourced on request through our authorised Walsin channel.

Can Venatech supply defence and automotive suppliers in Gebze, Turkey?

Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Turkey. Use the free cross-reference tool or upload a BOM; confirm import and end-use rules with your compliance team.


Share This, Choose Your Platform!