NEWS

Thin Film Chip Resistor for Denmark’s Medical Devices: a 10 Kilohm 0402 Brief Returns 86 Walsin Parts Against Stackpole RNCF

A thin film chip resistor sets gain and filter corners in the tiny analogue front ends of Danish hearing aids and medical wearables. A 10 kilohm 0402 brief returns 86 Walsin thin film parts, 33 of them at 0.1 percent or tighter and 25 ppm or better, against Stackpole RNCF. Venatech is the authorised Walsin distributor in Hong Kong.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for analogue engineers and buyers at Danish makers of hearing aids, hearing diagnostics, medical wearables and patient monitors. Walsin Technology (Walsin) is the line we are authorised for; Stackpole Electronics (SEI) is a line we supply, so an RNCF already on your parts list can be quoted as it stands or crossed to Walsin. We counted every Walsin figure below on 16 November 2026 in our Walsin thin film exports, Venatech_ThinFilm_WF.xlsx and Venatech_ThinFilm_WFQ.xlsx, and checked our ready stock snapshot dated 9 November 2026. Stackpole figures come only from the RNCF datasheet, SEI-RNCF.pdf on seielect.com, fetched the same day.

How fast is Denmark’s hearing-device business growing in 2026?

Fast. HearingTracker reported on 15 October 2026 that Danish hearing-care group Demant grew hearing aid sales to external customers 17 percent organically in the third quarter of 2026, with group revenue of 6.624 billion Danish kroner, up 21 percent as reported.

The same report said Demant raised its full-year organic growth outlook to 7 to 8 percent and named Oticon Reveal and Oticon Zeal as the products behind the quarter. Those are Demant’s figures as HearingTracker reported them, not ours. What the numbers tell a Danish design team is that hearing and medical wearables are a volume business, built around the smallest analogue boards in electronics. Each one carries precision resistors that set microphone pre-amp gain, filter corners, reference dividers and battery-charge sensing, mostly in 0402 and 0201. Our guide to passives for a medical device walks through the rest of such a board.

Where does a thin film chip resistor sit in a hearing aid or medical wearable?

In the gain and reference paths. A thin film chip resistor sets amplifier gain and filter corners where a 0.1 percent tolerance and 25 ppm or better TCR keep two channels matched across body-temperature swings, with lower current noise than a thick film part at the same value.

A 10 kilohm resistor is a common feedback and divider value in these front ends. Matching matters more than absolute value: two microphone channels whose gain resistors drift apart by 0.1 percent shift the directional response. Over a 30 degree swing, a 25 ppm part moves 0.075 percent and a 50 ppm part 0.15 percent, so the TCR grade decides how much of your error budget the resistor uses. Our post on thin film versus thick film chip resistors explains the construction difference behind the noise and drift figures.

How many Walsin thin film parts answer a 10 kilohm 0402 brief?

  1. We filtered Walsin’s WF precision and WF.Q AEC-Q200 thin film rows to 10 kilohm in 0402: 86 part numbers come back, 49 WF and 37 WF.Q, across seven tolerances from 0.01 to 1 percent and five TCR grades from 5 to 50 ppm.
10 kilohm 0402 cell Walsin parts TCR grades (export) Rated power (export) Example Match / mismatch with a 0.1 percent, 25 ppm brief
0.01 percent 7 5 to 50 ppm 0.0625 or 0.1 W WF04Z1002TTL Match on tolerance; pick a 25 ppm or better grade
0.05 percent 13 5 to 50 ppm 0.0625 or 0.1 W WF04W1002ATL Match on tolerance; pick a 25 ppm or better grade
0.02 percent 14 5 to 50 ppm 0.0625 or 0.1 W n/a Match on tolerance; pick a 25 ppm or better grade
0.1 percent 13 5 to 50 ppm 0.0625 or 0.1 W WF04U1002BTL Match on tolerance; pick a 25 ppm or better grade
0.25 to 1 percent 39 5 to 50 ppm 0.0625 or 0.1 W n/a Mismatch on tolerance

Of the 86, 33 hold 0.1 percent or tighter at 25 ppm or better, 20 WF and 13 WF.Q. Across all values, our exports hold 73,057 Walsin thin film part numbers in 0402 and 5,506 in 0201. We have not seen the 10 kilohm 0402 cell counted tolerance by tolerance anywhere else. One of them, WF04U1002BTL, is on our shelf in Hong Kong (snapshot 9 Nov 2026).

Which Walsin parts cross a Stackpole RNCF in 0402 and 0201?

Every RNCF precision grade at 10 kilohm. Stackpole’s RNCF datasheet lists 0402 at about 0.063 W and 50 V, tolerances from 0.01 to 1 percent, TCR of 10, 15, 25 or 50 ppm in the precision range and 2 or 5 ppm in the ultra-precision range, AEC-Q200 compliance and a range of -55 to +155 degree C.

Your RNCF brief, 10 kilohm RNCF (Stackpole datasheet) Walsin part Walsin (export) Match / mismatch Your incumbent
0402, 0.1 percent, 25 ppm 0.063 W WF04U1002BTL 0402, 0.1 percent, 25 ppm, 0.0625 W Match on every field we hold; no mismatch in our export
0402, 0.1 percent, 25 ppm, automotive-grade AEC-Q200 compliant WF04U1002BTLQ WF.Q (AEC-Q200), 0.0625 W Match; request the qualification report, no mismatch in our fields
0402, 0.05 percent, 10 ppm 0.063 W WF04W1002ATL 0.05 percent, 10 ppm, 0.1 W Match; mismatch on power, higher on Walsin
0402, 0.01 percent, 5 ppm, ultra-precision 0.063 W WF04Z1002TTL 0.01 percent, 5 ppm, 0.1 W Match on tolerance and TCR
0402, 2 ppm, ultra-precision 2 ppm grade no 2 ppm row; 5 ppm is the 10 kilohm floor n/a Mismatch on TCR
0201, 0.1 percent, 25 ppm about 0.05 W, 15 V WF02Q1002BTL 0201, 0.1 percent, 25 ppm, 0.05 W Match on size, tolerance, TCR, power

What should a Danish medical device team check before swapping a precision resistor?

Drift and matching first. Check the TCR grade against your channel-matching budget, then load-life drift at body temperature, then moisture and sulfur exposure for a worn device, then the documentation your quality system needs; a 0.1 percent, 25 ppm part over a 30 degree swing stays inside 0.175 percent.

Keep matched pairs in the same series and reel where you can, since tracking between two parts is tighter than either part’s absolute TCR. Walsin’s AEC-Q200 tag on WF.Q parts is Walsin’s own; Venatech makes no qualification claim of its own, so request the report for the exact part. Medical devices fall under their own regulatory regime; we give no regulatory or trade-compliance advice, so confirm with your compliance team. Our note on precision thin film tolerance and TCR sets out how Walsin encodes both in the part number.

How Venatech helps

Cross the analogue front end in one paste. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating tolerance, TCR, size and power as match or mismatch.

Paste your RNCF lines into the cross-reference tool, or upload the whole parts list as a BOM. We checked our ready stock: WF04U1002BTL, the 10 kilohm, 0.1 percent, 25 ppm 0402 part, is on our shelf in Hong Kong (snapshot 9 Nov 2026); the other crosses we source through our authorised Walsin channel on request. Stackpole RNCF lines are quoted too; Stackpole is a line we supply. We serve from Hong Kong in small lots, and we confirm availability, date code and lead time on each quote, with no price, lead-time or stock guarantee. The thin film range lists every Walsin series.

The short version

  • Demant grew hearing aid sales 17 percent organically in the third quarter of 2026, per HearingTracker on 15 October 2026.
  • A 10 kilohm 0402 brief returns 86 Walsin thin film parts; 33 hold 0.1 percent or tighter at 25 ppm or better.
  • Walsin crosses every RNCF precision grade at 10 kilohm in 0402, plus the 0201 0.1 percent, 25 ppm cell.
  • WF04U1002BTL is on our shelf in Hong Kong (snapshot 9 Nov 2026).

Send us the precision resistor lines from your hearing or medical board, and we will return the Walsin crosses with every difference stated. How much of your channel-matching budget does resistor TCR use today?

Related reading

Last reviewed: 16 November 2026.

Sources

Fetched 16 November 2026.

  • HearingTracker, “Demant raises 2026 outlook as its hearing aid sales surge 17% in Q3”, 15 October 2026: https://www.hearingtracker.com/de/news/demant-raises-2026-outlook-as-its-hearing-aid-sales-surge-17-in-q3
  • Stackpole datasheet, RNCF Series precision thin film chip resistor: https://www.seielect.com/catalog/SEI-RNCF.pdf
  • Venatech Walsin thin film exports (Venatech_ThinFilm_WF.xlsx, Venatech_ThinFilm_WFQ.xlsx) and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.

Frequently asked questions

What thin film chip resistor suits a hearing aid front end in Denmark?

Usually an 0402 or 0201 part at 0.1 percent and 25 ppm or better, chosen for channel matching and low noise. A 10 kilohm, 0.1 percent, 25 ppm 0402 such as Walsin WF04U1002BTL is a typical feedback or divider part.

How many Walsin thin film parts are there at 10 kilohm in 0402?

86 in our exports: 49 in the WF precision series and 37 in the WF.Q AEC-Q200 series, across tolerances from 0.01 to 1 percent and TCR grades from 5 to 50 ppm.

Which Walsin part crosses a Stackpole RNCF 0402 at 10 kilohm, 0.1 percent, 25 ppm?

WF04U1002BTL, at 0402, 0.1 percent, 25 ppm and 0.0625 W in our export, matching every field we hold. WF04U1002BTLQ is the WF.Q AEC-Q200 version.

Does Walsin offer a 2 ppm thin film resistor at 10 kilohm?

Not in our exports: 5 ppm is the tightest grade at 10 kilohm in 0402. Stackpole lists 2 ppm in its RNCF ultra-precision range, so a 2 ppm brief stays on Stackpole, which we can also quote.

Is a Walsin thin film resistor on your shelf in Hong Kong?

Yes, WF04U1002BTL is on our shelf in Hong Kong (snapshot 9 Nov 2026). Other Walsin thin film parts we source through our authorised channel on request, and we confirm availability on the quote.

Is Venatech authorised for Stackpole?

No. Venatech is the authorised Walsin distributor in Hong Kong; Stackpole is a line we supply, and we quote Stackpole RNCF lines alongside the Walsin cross.


Share This, Choose Your Platform!