A 630V MLCC is the workhorse snubber and DC-blocking capacitor on the high-voltage side of a rooftop solar inverter. Walsin lists 928 capacitors at 630 V, 554 in C0G and 374 in X7R, and 29 are on our shelf in Hong Kong (snapshot 9 Nov 2026). Venatech is the authorised Walsin distributor in Hong Kong, serving Tainan, Taiwan.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for power electronics and purchasing teams at inverter and power supply makers in Tainan and southern Taiwan. Walsin Technology (Walsin) is the line we are authorised for. On 17 November 2026 we parsed all eight of our MLCC upload files, Venatech_MLCC_Upload_01.xlsx to Venatech_MLCC_Upload_08.xlsx (23,360 distinct part numbers), filtered them to a 630 V rating and checked the result against our ready stock snapshot dated 9 November 2026. Every part number below is real and every count is ours.
How much rooftop solar does Tainan have?
About 2.2 gigawatts on roofs alone. United Daily News reported on 28 May 2026 that Tainan’s filed rooftop solar capacity reached 2,194.6 MW by the end of 2025, up 10.88 percent in a year and about 44 percent of the city’s installed solar, and that 81 percent of the 264 MW added in 2025 was rooftop.
Those are the city’s figures as reported by the paper, not ours. The shift matters to inverter designers: rooftop systems are smaller than ground-mounted farms, so they use string inverters, hybrid inverters with batteries, microinverters and module-level optimisers in larger numbers. Every one of those boxes has a DC link, a switching bridge and auxiliary power supplies running at hundreds of volts, and each switching node needs small high-voltage ceramic capacitors around it. A city adding roughly 214 MW of rooftop in a single year, on the paper’s percentages, is a steady source of that demand.
Where does a 630V MLCC sit in a rooftop solar inverter?
Across the switches, in the auxiliary supply and in DC-blocking paths. Walsin’s middle and high voltage approval sheet, dated September 2026, lists snubbers in high frequency power converters, high voltage coupling and DC blocking, and DC-DC converters as applications, and states that its X7R parts are not intended for AC line filtering.
A snubber capacitor sits beside a MOSFET, IGBT or diode to damp the ringing when it switches; a C0G part is usually preferred there because its capacitance does not move with voltage or temperature. The auxiliary flyback that powers the inverter’s controller takes its input from the high-voltage DC bus and often uses 630 V parts on its clamp and primary side. The same sheet warns that high-voltage capacitors may need a protective coating to prevent external arcing, a point to check on a crowded inverter board. Our guide to middle and high voltage MLCC from 200 V to 4 kV sets out Walsin’s voltage ladder.
How many Walsin capacitors are rated 630 V?
928, in eight sizes. We counted 928 Walsin MLCC part numbers rated 630 V: 554 in C0G and 374 in X7R, from 0805 to 2225, with 610 in the middle and high voltage series, 136 in the SH soft-termination series and 73 in AEC-Q200 automotive series.
| Size | Parts at 630 V |
|---|---|
| 0805 | 267 |
| 1206 | 332 |
| 1210 | 126 |
| 1808 | 28 |
| 1812 | 97 |
| 1825 | 23 |
| 2220 | 41 |
| 2225 | 14 |
The ceiling depends on dielectric: at 630 V the C0G parts reach 100 nF and the X7R parts reach 1 uF, both in the bigger bodies. Soft termination matters on large inverter boards that flex during assembly or thermal cycling, which is why the 136 SH parts are worth a look. The MLCC range lists every series, and the high voltage MLCC capacitance limit shows how capacitance falls as voltage rises. We have not seen this 630 V slice counted anywhere else.
Which Walsin parts answer a 10 nF, 630 V snubber brief?
33 in all; six cover the common choices. For a 10 nF, 630 V brief we found 33 Walsin part numbers; for a snubber the C0G 1206N103J631 is the closest match, and X7R, soft-termination and AEC-Q200 options follow in 0805 to 1812.
| Brief: 10 nF, 630 V | Walsin part | Size | Dielectric | Tolerance | Match / mismatch | Your incumbent |
|---|---|---|---|---|---|---|
| Snubber, stable value | 1206N103J631 |
1206 | C0G | 5 percent | Match for a snubber | |
| Smaller body | 0805B103K631 |
0805 | X7R | 10 percent | Mismatch in dielectric: X7R loses capacitance under DC bias | |
| Larger body, X7R | 1210B103K631 |
1210 | X7R | 10 percent | Mismatch in dielectric; more creepage | |
| Soft termination | SH31B103K631 |
1206 | X7R | 10 percent | Match on size; flex-crack resistant, X7R | |
| AEC-Q200 automotive | MT31B103K631 |
1206 | X7R | 10 percent | Match on size; automotive paperwork | |
| Wide body, X7R | 1812B103K631 |
1812 | X7R | 10 percent | Mismatch on footprint; for creepage-limited layouts |
Leave the last column for your current part, then check thickness, termination and DC-bias behaviour in Walsin’s datasheet for the series. An X7R part at 630 V can lose a large share of its capacitance near full rated voltage, so a snubber calculated with the nominal value can end up under-damped. For the automotive option, see AEC-Q200 MLCC: MT versus MG series.
Which Walsin 630 V capacitors are on the Hong Kong shelf?
29 of them. We checked all 928 Walsin 630 V capacitors against our snapshot of 9 November 2026: 29 are on our shelf in Hong Kong (snapshot 9 Nov 2026), from 4.7 pF to 680 nF, including 1206B153K631 at 15 nF, 1206B223K631 at 22 nF, 1812B104K631 at 100 nF and SH55B684K631 at 680 nF.
| On our shelf (snapshot 9 Nov 2026) | Size | Dielectric | Value |
|---|---|---|---|
1206N150J631 |
1206 | C0G | 15 pF |
1812N681J631 |
1812 | C0G | 680 pF |
1206B153K631 |
1206 | X7R | 15 nF |
1206B223K631 |
1206 | X7R | 22 nF |
1210B473K631 |
1210 | X7R | 47 nF |
1812B104K631 |
1812 | X7R | 100 nF |
SH55B684K631 |
2220 | X7R, soft termination | 680 nF |
The rest of the 928, including the 10 nF parts above, are sourced on request through our authorised Walsin channel; we confirm date code and lead time on each quote. The ready stock list shows all 29 as a dated snapshot. We give no stock or lead-time promise.
How Venatech helps: what can we cross for a Tainan inverter board?
The high-voltage capacitors and everything around them. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, and we quote small lots to Taiwan from Hong Kong.
Paste your capacitor lines into the cross-reference tool, or upload the full inverter BOM at /bom/, and request a quote through the site. Each result states what differs from your original: voltage, dielectric, size and termination. Hong Kong-based service gives you one contact for the Walsin lines and the passives around them. Certification of the inverter stays with you and your test house.
The short version
- Tainan’s rooftop solar reached 2,194.6 MW by end-2025, about 44 percent of the city’s solar, and 81 percent of 2025’s 264 MW was rooftop (United Daily News, 28 May 2026).
- Walsin’s high voltage approval sheet (September 2026) lists snubbers, DC blocking and DC-DC converters as applications.
- Walsin lists 928 capacitors at 630 V: 554 C0G and 374 X7R, in eight sizes.
- A 10 nF, 630 V brief returns 33 parts; 1206N103J631 is the C0G snubber choice.
- 29 Walsin 630 V capacitors are on our shelf in Hong Kong (snapshot 9 Nov 2026).
We will not call a part a drop-in match. We will show you where it differs. How much of your snubber capacitance is left at full bus voltage?
Related reading
- Middle and high voltage MLCC, 200 V to 4 kV
- The high voltage MLCC capacitance limit
- AEC-Q200 MLCC: MT versus MG series
- Free cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 17 November 2026.
Sources
Fetched 17 November 2026.
- United Daily News, Tainan rooftop solar makes up 80 percent of new capacity (in Chinese), 28 May 2026: https://udn.com/news/story/7326/9530696
- Walsin, Multilayer Ceramic Capacitors approval sheet, Middle and High Voltage Series (200 V to 4 kV), September 2026, held as 04_Middle_and_High_Voltage.pdf.
- Venatech MLCC upload files Venatech_MLCC_Upload_01.xlsx to _08.xlsx and ready stock snapshot dated 9 November 2026, re-measured 17 November 2026.
Frequently asked questions
What is a 630V MLCC used for in a solar inverter?
Mainly as a snubber across switching devices, for DC blocking and coupling, and in the auxiliary DC-DC supply that runs from the high-voltage bus, as Walsin’s approval sheet lists.
How many 630V MLCC parts does Walsin make?
928 in our count of 17 November 2026: 554 C0G and 374 X7R, from 0805 to 2225, including 136 soft-termination and 73 AEC-Q200 parts.
Should a solar inverter snubber use C0G or X7R?
C0G is usually preferred, because its capacitance does not fall with applied voltage or temperature. X7R parts at 630 V can lose much of their value near rated voltage.
Which Walsin part crosses a 10 nF 630 V 1206 capacitor?
1206N103J631 in C0G, or SH31B103K631 and MT31B103K631 in X7R if you need soft termination or AEC-Q200. Check thickness and DC bias against both datasheets.
Does Venatech stock 630 V capacitors in Hong Kong?
29 Walsin 630 V parts are on our snapshot of 9 November 2026, from 4.7 pF to 680 nF. Others are sourced on request through our authorised Walsin channel.
Can Venatech supply inverter makers in Tainan, Taiwan?
Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Taiwan. Use the free cross-reference tool or upload a BOM; confirm import rules with your compliance team.