NEWS

Automotive Ferrite Bead for EV Electronics in China: NEV Exports Reach 606,000 in October and Walsin Lists 150 Automotive Chip Beads

For an automotive ferrite bead on EV electronics built in China, Walsin Technology (Walsin) lists 150 chip beads in its two automotive bead series, from 0402 to 1812, and 80 of them are rated 1 A or more. Venatech, Walsin’s authorised distributor in Hong Kong, crosses your bead and quotes the Walsin line.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for EMC and hardware engineers in China whose boards now ship inside export vehicles: on-board chargers, BMS controllers, ADAS cameras, domain controllers and infotainment heads. The news fact below names its source and date. The part counts are ours: we parsed Walsin’s inductor exports, Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx (5,410 real part numbers once the one test row is removed), and read each bead against Walsin’s MHC-G.pdf and MCB-B.pdf datasheets.

What did CAAM report for China’s NEV sales and exports in October 2026?

A monthly record, driven by exports. CnEVPost reported on 11 November 2026, citing the China Association of Automobile Manufacturers (CAAM), that NEV sales reached 1.94 million in October, up 13.1 percent year on year, and that NEV exports reached 606,000, up about 140 percent.

The same report puts NEVs at 64.3 percent of all vehicle sales in October, and says exports made up about 31.2 percent of NEV sales that month. Battery-electric exports were 374,000 and plug-in hybrid exports 233,000. From January to October, CAAM counted 4.612 million NEV exports, up 129 percent, while domestic NEV sales fell 10.3 percent. We add no forecast. For an electronics engineer in China, the point is simple: close to one NEV in three that left a factory in October went abroad, and every one of them carries boards that must pass the EMC rules of the market it lands in.

Why does an export EV built in China need an automotive ferrite bead on every noisy line?

Because a bead is the cheapest place to stop conducted noise. An automotive ferrite bead is a chip that looks resistive at high frequency; Walsin rates its automotive beads from 20 ohm to 2,500 ohm at 100 MHz, so one part can damp a switching edge on a supply rail, a camera link or a CAN line.

An EV is a noisy box. Traction inverters, DC-DC converters and on-board chargers switch fast, and that energy reaches every harness. Each controller filters its own inputs, and the bead is usually the first part on a rail entering a sensor or a processor. An export programme adds a second pressure: the same board may be tested against several regional EMC regimes, and a late bead change is a requalification event. We give no legal or homologation advice; confirm those rules with your compliance team. Our explainer on ferrite bead vs inductor covers the physics, and Walsin automotive inductors: MCB, MHC and MCI maps the families.

How many automotive ferrite beads does Walsin list, and in which sizes?

One hundred and fifty, in seven case sizes. We counted 150 distinct Walsin part numbers in the MCB / MHC Automotive series: 82 MHC parts on the MHC-G.pdf datasheet and 68 MCB parts on the MCB-B.pdf datasheet, from 0402 up to 1812, with 80 of the 150 rated 1 A or more.

Walsin automotive beads by case size Part numbers Impedance range at 100 MHz
0603 (1608) 68 20 to 2,500 ohm
0805 (2012) 40 30 to 2,200 ohm
0402 (1005) 23 60 to 1,800 ohm
1206 (3216) 9 50 to 600 ohm
1806 (4516) 6 60 to 1,000 ohm
1210 (3225) 2 1,000 ohm
1812 (4532) 2 680 ohm
Total 150

Seventeen of the 150 sit at exactly 600 ohm at 100 MHz, the value most EMC engineers reach for first on a digital supply rail. We have not seen the automotive bead range broken down this way elsewhere. Walsin also lists 139 MCI Automotive chip inductors, which are a separate job (RF matching and filters) and are not counted here.

Which Walsin bead fits a 600 ohm, 0603, 1 A automotive brief?

Two parts match exactly. For a brief of 600 ohm at 100 MHz, 0603 case and at least 1 A, MHC1608S601LZP (0.2 ohm DC resistance) and MHC1608P601ZZP (0.15 ohm) both match; the 0805 and 1206 MHC parts match the rating in a larger case.

Put your incumbent bead in the last column and compare each field.

Walsin part Size Impedance at 100 MHz DC resistance Rated current Match / mismatch with 600 ohm, 0603, 1 A or more Your incumbent
MHC1608S601LZP 0603 600 ohm 0.2 ohm 1,000 mA Match
MHC1608P601ZZP 0603 600 ohm 0.15 ohm 1,000 mA Match, lower DC resistance
MHC2012S601NZP 0805 600 ohm 0.09 ohm 1,000 mA Match on rating; larger case, check the land
MHC3216S601MZE 1206 600 ohm 0.08 ohm 1,000 mA Match on rating; larger case
MCB1608S601HZP 0603 600 ohm 0.38 ohm 500 mA Mismatch: current below 1 A
MCB1608H601EZP 0603 600 ohm 0.65 ohm 200 mA Mismatch: current below 1 A
MCB1005B601EZP 0402 600 ohm 0.65 ohm 200 mA Mismatch: case and current

Most of these codes come in pairs that differ by one letter near the end, for example MHC1608S601LZP and MHC1608S601LHP. Read the datasheet for what that letter sets before you pick one, and order the one your drawing names.

What should an engineer in China check before swapping a bead on an export model?

Four fields and one document. Check impedance at the frequency of your noise (not only at 100 MHz), DC resistance against your rail drop, rated current with margin, and case size; then ask for the AEC-Q200 qualification data, because Walsin’s export does not carry it as a column.

A bead’s impedance falls as DC current rises, so a 600 ohm part on a 1 A rail filters less than its headline. A lower DC resistance, such as the 0.15 ohm MHC1608P601ZZP, wastes less voltage on a 3.3 V or 1.8 V rail. If your programme is mid-life, treat any bead swap as a change that needs EMC re-test on the target vehicle. Our AEC-Q200 qualification report guide lists what to request. Walsin describes automotive parts as qualified to AEC-Q200; confirm the status for each part on its datasheet.

Can Venatech supply Walsin automotive beads from Hong Kong?

Yes, to order. All 150 Walsin automotive beads can be quoted from Hong Kong: none is on our shelf in the snapshot dated 9 November 2026, so request a quote and we source them through our authorised Walsin channel.

Each quote states availability, date code and lead time for the line, and we work in small lots for prototypes, EMC test builds and pilot runs. We make no stock, price or lead-time promise. The ready-stock list is a dated snapshot; check it for the capacitors and resistors that sit beside the bead on the same rail.

How Venatech helps: what should an EV electronics team in China send us?

The EMI parts from your BOM. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.

Paste a bead code into the cross-reference tool, or upload the whole BOM and request a quote through the site. The ready-stock snapshot is dated 9 November 2026. We serve Shenzhen, Shanghai, Hefei and Chongqing from Hong Kong, with fast quotes and small lots. The full inductor and bead range lists every Walsin part. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.

The short version

CAAM counted 606,000 NEV exports from China in October, up about 140 percent, CnEVPost reported on 11 November 2026. Each export vehicle carries controllers that must pass EMC tests abroad, and the ferrite bead is the first filter on many of their lines. Walsin covers the job with 150 automotive chip beads from 0402 to 1812, 80 of them rated 1 A or more, and MHC1608S601LZP meets a 600 ohm, 0603, 1 A brief exactly.

Send us the beads on your export programme and we will return Walsin crosses with every difference stated. Which rail on your board failed its last EMC scan?

Related reading

Last reviewed: 17 November 2026.

Sources

Fetched 17 November 2026.

  • CnEVPost, report on China NEV sales and exports for October 2026 (CAAM data), 11 November 2026: https://cnevpost.com/2026/11/11/china-nev-sales-oct-2026-caam/
  • Walsin inductor exports, Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx, re-measured 17 November 2026; Walsin MHC-G.pdf and MCB-B.pdf datasheets; Venatech Hong Kong stock snapshot dated 9 November 2026.

Frequently asked questions

How many NEVs did China export in October 2026?

CnEVPost reported on 11 November 2026, citing CAAM, that NEV exports reached 606,000 in October, up about 140 percent year on year, out of 1.94 million NEV sales.

What is an automotive ferrite bead used for in an EV?

It damps high-frequency conducted noise on a supply rail, camera link or bus line. Walsin rates its automotive beads from 20 ohm to 2,500 ohm at 100 MHz.

How many automotive ferrite beads does Walsin list?

We counted 150 in the MCB / MHC Automotive series, from 0402 to 1812. Eighty are rated 1 A or more and 17 sit at 600 ohm at 100 MHz.

Which Walsin part crosses a 600 ohm 0603 automotive bead rated 1 A?

MHC1608S601LZP and MHC1608P601ZZP both match 600 ohm, 0603 and 1,000 mA. Confirm the impedance curve and DC bias behaviour against both datasheets before release.

Are Walsin automotive beads AEC-Q200 qualified?

Walsin files them under its Automotive series, and the export carries no AEC-Q200 column. Ask for the qualification data and confirm each part on its datasheet.

Can Venatech supply Walsin automotive beads to China from Hong Kong?

Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong. Request a quote and we source the beads through our authorised Walsin channel, with availability, date code and lead time stated on each quote.


Share This, Choose Your Platform!