For a current sense resistor on AI server power in Taiwan, Walsin Technology (Walsin) lists 1,188 metal current-sense chip resistors, and 156 of them are 2512 parts rated 3 W, from 0.5 to 100 milliohm. Venatech, Walsin’s authorised distributor in Hong Kong, crosses your shunt and quotes the Walsin line.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for power engineers in Taiwan designing rack power shelves, hot-swap and e-fuse stages, battery backup units and 48 V or 54 V bus converters for AI racks. We parsed Walsin’s chip resistor exports (Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_34.xlsx, 234,378 distinct part numbers) and read the metal shunt rows against Walsin’s ASC_WW25A.pdf, ASC_WW25B.pdf and ASC_WW25J-WW25K.pdf datasheets. The news figure names its source and its date.
What did Hon Hai report for the third quarter of 2026?
A record quarter led by cloud hardware. Focus Taiwan reported on 12 November 2026 that Hon Hai’s third-quarter net profit reached 77.52 billion New Taiwan dollars, up 34 percent, on revenue of 3.02 trillion New Taiwan dollars, up 46 percent year on year.
The same report says cloud and networking products made up 54 percent of revenue, up from 51 percent in the second quarter, and that the core business, including AI servers and AI racks, grew more than the company expected. Gross margin was 6.02 percent. We add no forecast and say nothing about any company’s suppliers. For a power engineer in Taiwan, the signal is that rack-level AI hardware keeps taking a larger share of Hon Hai’s sales, and each rack carries power stages that measure current at every level.
Where does a current sense resistor sit in an AI server rack?
At every point where current must be known. A current sense resistor is a low-value shunt, typically 0.5 to 10 milliohm on rack power, whose voltage drop tells a controller how much current flows; Walsin’s metal range spans 0.5 to 700 milliohm across nine case sizes.
In a rack you find shunts in the power-shelf output stages, in hot-swap and e-fuse circuits on each tray’s 48 V or 54 V input, in battery backup units, and in the multiphase regulators feeding accelerators. The shunt protects against inrush and faults, feeds telemetry, and balances phases. Metal plate and metal foil parts are preferred here over thick film because they reach lower values, carry more power in the same footprint and drift less with temperature. Our guide to thick film vs metal low-ohm current sense resistors sets out the trade-off, and the chip resistor range lists every part.
How many metal current sense resistors does Walsin list, and at what power?
One thousand one hundred and eighty-eight. We counted 1,188 distinct part numbers in Walsin’s metal low-ohm current sense group, in nine case sizes from 0306 to 2512; 625 are 2512 parts, and 156 of those are rated 3 W.
| Case size | 0.5 W or less | 0.75 W | 1 W | 2 W | 3 W | Total |
|---|---|---|---|---|---|---|
| 2512 (6432) | 0 | 0 | 196 | 273 | 156 | 625 |
| 1206 (3216) | 106 | 0 | 269 | 0 | 0 | 375 |
| 0805 (2012) | 15 | 46 | 0 | 0 | 0 | 61 |
| 1225 (3263) | 0 | 0 | 0 | 47 | 0 | 47 |
| 2010 (5025) | 8 | 0 | 20 | 0 | 0 | 28 |
| 0603 (1608) | 20 | 0 | 0 | 0 | 0 | 20 |
| 0612 (1632) | 0 | 0 | 17 | 0 | 0 | 17 |
| 0306 and 0402 | 15 | 0 | 0 | 0 | 0 | 15 |
| Total | 164 | 46 | 502 | 320 | 156 | 1,188 |
The 156 parts at 3 W are all 2512 and run from 0.5 milliohm to 100 milliohm. We found 509 of the 1,188 codes end in J, and every one of them points to a Walsin automotive datasheet (the _J or _AUTO files); that matters to a server team only if a customer asks for that documentation. We have not seen the metal shunt range laid out by size and power this way elsewhere.
Which Walsin current sense resistor fits a 1 milliohm, 2512, 2 W brief?
Five parts meet it. For a brief of 1 milliohm, ±1 percent, 2512 and at least 2 W, WW25AR001FTL and WW25BR001FTL match at 3 W, and WW25KR001FTL, WW25NR001FTL and WW25RR001FTL match at 2 W.
Put your incumbent shunt in the last column and compare each field.
| Walsin part | Resistance | Tolerance | TCR (ppm/°C) | Rated power | Match / mismatch with 1 milliohm, ±1%, 2512, 2 W or more | Your incumbent |
|---|---|---|---|---|---|---|
WW25AR001FTL |
1 milliohm | ±1% | ±70 | 3 W | Match, 1 W of headroom | |
WW25BR001FTL |
1 milliohm | ±1% | ±70 | 3 W | Match, 1 W of headroom | |
WW25KR001FTL |
1 milliohm | ±1% | ±70 | 2 W | Match | |
WW25NR001FTL |
1 milliohm | ±1% | ±70 | 2 W | Match | |
WW25RR001FTL |
1 milliohm | ±1% | ±75 | 2 W | Match; TCR slightly wider | |
WW25JR001FTL |
1 milliohm | ±1% | ±70 | 1 W | Mismatch: power below 2 W | |
WW25AR001JTL |
1 milliohm | ±5% | ±70 | 3 W | Mismatch: tolerance | |
WW25AR0L5FTL |
0.5 milliohm | ±1% | ±70 | 3 W | Mismatch on value; fits a higher-current brief |
The A, B, K, N and R families differ in construction and pad layout, so check the land pattern on each datasheet before you assume a footprint swap. Confirm against both datasheets and qualify in your own circuit.
How much current can a 1 milliohm shunt carry at 3 W?
About 55 A at full rating. From P = I²R, a 1 milliohm shunt reaches 3 W at about 55 A and 2 W at about 45 A; a 0.5 milliohm part such as WW25AR0L5FTL reaches 3 W at about 77 A, at half the sense voltage.
Those are ceilings at the datasheet’s rated temperature, not design points. Above that temperature the power rating derates, and a server tray runs warm. Most designers keep continuous dissipation well under the rating and size copper for heat spreading. The lower the value, the smaller the signal: 1 milliohm at 30 A gives 30 mV for the amplifier, 0.5 milliohm gives 15 mV, so amplifier offset becomes the accuracy limit. A wider TCR adds error as the board heats.
Can Venatech supply Walsin current sense resistors from Hong Kong?
Yes, to order. All 1,188 Walsin metal current sense resistors can be quoted from Hong Kong: none is on our shelf in the snapshot dated 9 November 2026, so request a quote and we source them through our authorised Walsin channel.
Each quote states availability, date code and lead time for the line, and we work in small lots for engineering builds and pilot runs. We make no stock, price or lead-time promise. The ready-stock list, a dated snapshot, covers MLCC and chip resistors that may sit on the same power board.
How Venatech helps: what should a Taiwan power team send us?
The shunts and sense parts from your BOM. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.
Paste a shunt code into the cross-reference tool, or upload the whole BOM and request a quote through the site. The ready-stock snapshot is dated 9 November 2026. We serve Taoyuan, Hsinchu and Taichung from Hong Kong, with fast quotes and small lots. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.
The short version
Hon Hai’s third-quarter revenue rose 46 percent to 3.02 trillion New Taiwan dollars, with cloud and networking at 54 percent of sales, Focus Taiwan reported on 12 November 2026. Every AI rack measures current with shunts in its power shelf, hot-swap stages and backup units. Walsin covers the job with 1,188 metal current sense resistors, 156 of them 2512 parts at 3 W, and WW25AR001FTL meets a 1 milliohm, 2 W brief with a watt to spare.
Send us the shunts on your power shelf and we will return Walsin crosses with every difference stated. Which stage on your tray runs closest to its shunt’s rating?
Related reading
- Low-ohm current sense: thick film vs metal
- Thick film current sense resistor selection by rated power
- What resistor TCR actually buys you
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 17 November 2026.
Sources
Fetched 17 November 2026.
- Focus Taiwan (CNA), report on Hon Hai’s third-quarter 2026 results, 12 November 2026: https://focustaiwan.tw/business/202611120018
- Walsin chip resistor exports, Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_34.xlsx, re-measured 17 November 2026; Walsin ASC_WW25A.pdf, ASC_WW25B.pdf, ASC_WW25J-WW25K.pdf, ASC_WW25N.pdf and ASC_WW25R.pdf datasheets; Venatech Hong Kong stock snapshot dated 9 November 2026.
Frequently asked questions
What did Hon Hai report for the third quarter of 2026?
Focus Taiwan reported on 12 November 2026 a record net profit of 77.52 billion New Taiwan dollars, up 34 percent, on revenue of 3.02 trillion New Taiwan dollars, up 46 percent. Cloud and networking made up 54 percent of revenue.
What current sense resistor value suits a 48 V AI server tray?
Rack hot-swap and power-shelf stages typically use 0.5 to 10 milliohm metal shunts. Pick the value from the full-load current, the sense voltage your amplifier needs and the power the part can carry with margin.
How many metal current sense resistors does Walsin list?
We counted 1,188 in Walsin’s metal low-ohm current sense group, in nine case sizes. 625 are 2512 and 156 of those are rated 3 W.
Which Walsin part crosses a 1 milliohm 2512 shunt rated 2 W?
WW25KR001FTL and WW25NR001FTL match at 2 W, and WW25AR001FTL and WW25BR001FTL match at 3 W. Check the pad layout and derating curve on each datasheet before release.
How much current can a 1 milliohm 3 W shunt carry?
About 55 A at full rated power, from P = I²R. Derate for temperature and keep continuous dissipation well below the rating.
Can Venatech supply Walsin current sense resistors to Taiwan from Hong Kong?
Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong. Request a quote and we source the parts through our authorised Walsin channel, with availability, date code and lead time stated on each quote.