Ferrite bead vs inductor comes down to loss: a bead turns high-frequency noise into heat, while an inductor stores energy and can resonate. Walsin lists 610 ferrite beads beside 4,801 other inductors, and 12 of its 0603 beads reach 600 ohm at 500 mA or more. Venatech is the authorised Walsin distributor in Hong Kong, serving Ireland.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for hardware and EMC engineers, and the buyers beside them, at medical device makers and contract manufacturers in Galway, Limerick, Cork and across Ireland. Walsin Technology (Walsin) is the line we are authorised for. On 16 November 2026 we parsed all 5,411 part numbers in our inductor upload files, Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx, separated the parts that publish an impedance at 100 MHz, which are the ferrite beads, and checked the result against our ready stock snapshot dated 9 November 2026. Every part number below is real.
How big is the medtech sector in Ireland?
About 20 billion euros of exports a year. Ibec’s Irish Medtech Association said on 19 August 2026 that the sector exports 20 billion euros, employs about 50,000 people across 550 companies, and that 80 percent of those businesses are start-ups or SMEs.
Those are Ibec’s figures, not ours, and we name no company’s suppliers. What they mean for passives is volume and variety: patient monitors, infusion pumps, wearables, diagnostic instruments and their contract manufacturers all have to pass the EMC collateral standard IEC 60601-1-2, and the first parts an EMC engineer reaches for after a failed scan are a ferrite bead or a small inductor on a power or signal line. The 80 percent SME share is also why small-lot supply matters in Ireland.
Ferrite bead vs inductor: what is the actual difference?
Where the energy goes. A ferrite bead is specified by its impedance at 100 MHz, typically tens to thousands of ohm, and most of that impedance is resistive above a few tens of megahertz, so it absorbs noise; a chip inductor is specified by its inductance and Q and is meant to store energy with low loss.
That difference decides the job. A bead on a sensor or ADC supply soaks up switching harmonics and clock noise without forming a sharp resonance, which is why it suits broadband EMI. An inductor in an LC filter gives a steeper roll-off at lower frequencies, but it rings with the capacitors around it and turns capacitive above its self-resonant frequency. Two cautions apply to beads: impedance falls as DC current rises, so a 600 ohm bead at its rated current is much less than 600 ohm, and a bead plus a large ceramic capacitor can still peak at low frequency. Our explainer on ferrite bead vs inductor impedance at 100 MHz shows the curves.
How many ferrite beads does Walsin list, and in which sizes?
610 beads among 5,411 inductor part numbers. We found 610 distinct Walsin part numbers that publish an impedance at 100 MHz; 177 are in 0603, from 10 to 2,500 ohm, and 17 of those 0603 beads are rated 600 ohm, 12 of them at 500 mA or more.
| Bead size | Walsin beads | Note from our count |
|---|---|---|
| 0402 | 91 | 7 rated 600 ohm in the WLBD and MCB families |
| 0603 | 177 | 10 to 2,500 ohm; 17 at 600 ohm |
| 0805 | 211 | 175 listed as 2012(0805) and 36 as metric 2012 |
| 1206 | 72 | higher-current power-line beads |
| 1210, 1806 and 1812 | 59 | high-current and array-style bodies |
The 610 beads come mainly from the WLBD, WQBD, MCB, MHC, SCA, SCM, WTCF, WQCF, BIH and WTBL families, with 150 in the MCB / MHC automotive series. The most common value is 120 ohm, 70 parts, then 600 ohm, 60 parts. We have not seen this bead split counted anywhere else.
Which Walsin parts fit a 0603 bead on a 3.3 V medical sensor rail?
Twelve at 600 ohm and 500 mA or more. For a 0603, 600 ohm bead on a 3.3 V sensor rail drawing 300 mA, we shortlisted Walsin parts rated 500 mA to 1 A with DC resistance from 0.15 to 0.4 ohm, including WLBD1608HCU601TH at 1 A and MHC1608S601LBP at 1,000 mA.
| Brief: 0603, 600 ohm at 100 MHz, 300 mA rail | Walsin part | Type | Rated current | DC resistance | Export file | Match / mismatch |
|---|---|---|---|---|---|---|
| High-current bead | WLBD1608HCU601TH |
Bead, WLBD(HC) | 1 A | 0.2 ohm | Venatech_Inductor_Upload_01.xlsx | Match, most current headroom |
| MHC-S bead | MHC1608S601LBP |
Bead, MHC-S | 1,000 mA | 0.2 ohm | Venatech_Inductor_Upload_02.xlsx | Match |
| Automotive MHC bead | MHC1608P601ZZP |
Bead, MCB / MHC automotive | 1,000 mA | 0.15 ohm | Venatech_Inductor_Upload_02.xlsx | Match, lowest DC resistance here |
| MCB-S bead | MCB1608S601IBP |
Bead, MCB-S | 600 mA | 0.4 ohm | Venatech_Inductor_Upload_01.xlsx | Match; check impedance at 300 mA |
| MCB-S bead | MCB1608S601HBP |
Bead, MCB-S | 500 mA | 0.4 ohm | Venatech_Inductor_Upload_01.xlsx | Match, least margin |
| Low-current bead | WLBD1608K2U601TP |
Bead, WLBD | 200 mA | 0.45 ohm | Venatech_Inductor_Upload_01.xlsx | Mismatch: rated below the 300 mA rail |
| Inductor instead | MIP1608P1R0MBP |
1 uH inductor, MIP-P | 950 mA | 0.2 ohm | Venatech_Inductor_Upload_01.xlsx | Mismatch in function: an LC element, not a lossy bead |
Run a bead well below its rated current if you need its impedance: a part rated 1 A carrying 300 mA keeps far more of its 600 ohm than one rated 500 mA. Our post on Walsin automotive inductors MCB, MHC and MCI explains those families. The inductor range page lists every series.
When is a chip inductor the better choice than a ferrite bead?
Below about 30 MHz, and in a DC-DC stage. A 1 uH chip inductor such as MIP1608P1R0MBP, rated 950 mA with a listed self-resonant frequency of 60 MHz, or the power inductor MAP1608ST1R0MMPK at 1.9 A and 0.089 ohm, belongs in an LC filter or converter, where a bead’s loss would waste energy or saturate.
Choose an inductor for a pi or LC filter that must attenuate a switching frequency in the hundreds of kilohertz, for the power stage of a buck converter, or where you need a predictable value in a tuned circuit. Choose a bead for broadband suppression from tens of megahertz up, on supplies to sensors, radios and ADC references, and on signal lines where a little series resistance is harmless. In a patient-connected device, many designs use both: an inductor in the converter, a bead after it at the load. For the DC resistance trade, see reading RDC in inductors. Request a quote for any line here: we source it through our authorised Walsin channel.
How Venatech helps: what can an Irish medtech team send us?
Your EMI fix list, and we return Walsin beads and inductors with impedance, current and DC resistance stated. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, including the 610 beads and 4,801 other inductors counted here.
Paste a bead or inductor into the cross-reference tool or upload the BOM at /bom/. Check the dated ready stock list and request a quote through the site. We serve Ireland from Hong Kong in small lots, which suits EMC fixes, pilot builds and the many SMEs in Irish medtech, and we confirm availability and date code on each quote. Device qualification stays with you.
The short version
- Ibec’s Irish Medtech Association said on 19 August 2026 that the sector exports 20 billion euros and employs about 50,000 people in 550 companies.
- Ferrite bead vs inductor: a bead absorbs high-frequency noise as heat; an inductor stores energy, gives steeper low-frequency roll-off and can resonate.
- Walsin lists 610 ferrite beads beside 4,801 other inductors; 177 beads are 0603, and 12 of the 17 at 600 ohm are rated 500 mA or more.
- Run a bead well under its rated current, because its impedance falls with DC bias.
Send us the beads and filter inductors from your device and we will return the Walsin crosses with every difference stated. Which frequency band failed your last EMC scan?
Related reading
- Ferrite bead vs inductor: impedance at 100 MHz
- Walsin automotive inductors: MCB, MHC and MCI
- Reading RDC: inductor DC resistance
- Cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 16 November 2026
Sources
Fetched 16 November 2026.
- Ibec, External threats mean Budget 2027 requires decisive action to safeguard global hub Irish Medtech, 19 August 2026: https://www.ibec.ie/connect-and-learn/media/2026/08/19/external-threats-mean-budget-2027-requires-decisive-action-to-safeguard-global-hub-irish-medtech
- Venatech inductor upload files Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx, and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.
Frequently asked questions
Ferrite bead vs inductor: which should I use for EMI?
A ferrite bead for broadband suppression from tens of megahertz up, because it absorbs noise as heat; an inductor for LC filters and converters at lower frequencies. Many medical designs use both.
How many ferrite beads does Walsin make?
610 in our count of 16 November 2026, among 5,411 inductor part numbers, from 0402 to 1812, with 177 in 0603.
Which Walsin 600 ohm 0603 ferrite bead has the most current rating?
WLBD1608HCU601TH at 1 A, and MHC1608S601LBP and MHC1608P601ZZP at 1,000 mA. Twelve Walsin 0603 beads at 600 ohm are rated 500 mA or more.
Why does a ferrite bead lose impedance under DC current?
The ferrite partly saturates as DC bias rises, so the impedance at 100 MHz falls. Pick a bead rated well above your rail current and read the bias curve in the datasheet.
Does Venatech stock Walsin ferrite beads in Hong Kong?
Check the dated ready stock page. For bead lines not on it, request a quote and we source them through our authorised Walsin channel, confirming availability on each quote.
Can Venatech supply medical device makers in Ireland?
Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Ireland. Use the cross-reference tool or upload a BOM; confirm import rules with your compliance team.