NEWS

X1/Y2 vs X1/Y1 Safety Capacitor Selection for Heat Pump Electronics in Portugal: 367 Walsin Disc Parts in 8 Ratings

An X1/Y2 safety capacitor suits a line-to-earth position needing basic insulation; an X1/Y1 part is for positions bridging reinforced insulation. Walsin lists 367 safety disc capacitors in 8 voltage ratings: 186 X1/Y2 up to 10 nF and 181 X1/Y1 up to 4.7 nF. Venatech is the authorised Walsin distributor in Hong Kong, serving Portugal.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for power-electronics and EMC engineers, and the buyers beside them, at heat pump, appliance and HVAC electronics makers in Aveiro and across Portugal. Walsin Technology (Walsin) is the line we are authorised for. On 16 November 2026 we parsed all 929 part numbers in our disc capacitor upload file, Venatech_DiscCap_Upload_01.xlsx, and the 160 S2 safety MLCC in Venatech_MLCC_Upload_08.xlsx, then checked both against our ready stock snapshot dated 9 November 2026. Every part number below is real.

What is Bosch investing in Aveiro, Portugal?

Heat pump development and manufacturing, as part of a wider Portugal programme. The Portugal News reported on 7 July 2026 that Bosch is investing at least eighty-five million euros in its Portuguese operations, naming Aveiro for heat pump development and manufacturing, Braga for mobility electronics and automotive radar, and Lisbon for service operations.

Bosch’s own press release of 6 November 2023 had already set out about 100 million euros for Aveiro by 2026, including two production buildings and lines for the outdoor and wall-mounted indoor units of its propane heat pumps. Those are Bosch’s and the newspaper’s figures, not ours, and we make no claim about which components Bosch or its suppliers use. For Portuguese engineers the relevance is direct: every inverter-driven heat pump has a mains EMI filter, and that filter carries Y capacitors from line and neutral to earth, plus X capacitors across the line.

What is the difference between an X1/Y2 and an X1/Y1 safety capacitor?

The insulation it may bridge and the impulse it must survive. Under IEC 60384-14, as summarised by TechOverflow, a Y1 capacitor is tested at an 8 kV impulse and a Y2 at 5 kV, while X1 is tested at 4 kV and X2 at 2.5 kV; a dual-rated X1/Y2 or X1/Y1 part can sit in either kind of position within its ratings.

In practice, Y2 is the usual line-to-earth choice in equipment with basic insulation and a protective earth, which describes most heat pump outdoor units. Y1 is the class for positions that bridge double or reinforced insulation, for example from a primary circuit to an accessible secondary or to a Class II enclosure. The X1 half of the rating matters if the same footprint may be used across the line, where X1 survives a higher surge than X2. Which class a position needs is set by your product standard and insulation diagram, not by the capacitor. See X1/Y1 vs X1/Y2 safety capacitors for the background.

How many Walsin safety disc capacitors are there, by class and rating?

367, in 8 ratings. We counted 367 distinct Walsin safety disc capacitors: 186 X1/Y2 in the AC series and 181 X1/Y1 in the AH and AS series; the Y2 ratings reach 500 Vac and 10 nF, and the Y1 ratings reach 500 Vac and 4.7 nF.

Rating printed in the export Class Parts Capacitance range
X1-440Vac / Y2-250Vac X1/Y2 57 10 pF to 10 nF
X1-440Vac / Y2-300Vac X1/Y2 57 10 pF to 10 nF
X1-440Vac / Y2-300Vac, 1500 Vdc (Auto) X1/Y2 23 100 pF to 10 nF
X1-500Vac / Y2-500Vac, 1500 Vdc X1/Y2 49 10 pF to 10 nF
X1-400Vac / Y1-250Vac X1/Y1 56 10 pF to 4.7 nF
X1-400Vac / Y1-400Vac X1/Y1 56 10 pF to 4.7 nF
X1-500Vac / Y1-500Vac, 1500 Vdc X1/Y1 54 10 pF to 4.7 nF
X1-760Vac / Y1-500Vac (AS) X1/Y1 15 100 pF to 4.7 nF

Dielectrics run from SL Class I, 126 parts, to Y5P, Y5U and Y5V Class II, and the Class II parts are where the nanofarad values live. Walsin’s export lists the approval bodies on every safety row, from UL and CSA to VDE/ENEC and CQC. We have not seen this class-by-rating split counted anywhere else.

Which Walsin parts cross a 2.2 nF Y capacitor in a heat pump EMI filter?

Twenty, ten in each class. At 2.2 nF we found 20 Walsin safety discs, 10 rated X1/Y2 and 10 rated X1/Y1, all specified from minus 40 to plus 125 degrees; for a 230 Vac line-to-earth position the small-size YU0AC222M070 and YU1AC222M070 are the compact Y2 options.

Brief: 2.2 nF Y cap, 230 Vac, line to earth Walsin part Class Rating Diameter code Export file Match / mismatch
Basic insulation, compact YU0AC222M070 X1/Y2 Y2 250 Vac 70 Venatech_DiscCap_Upload_01.xlsx Match
More AC margin YU1AC222M070 X1/Y2 Y2 300 Vac 70 Venatech_DiscCap_Upload_01.xlsx Match, more voltage margin
500 Vac or 400 V three-phase YU5AC222M080 X1/Y2 Y2 500 Vac 80 Venatech_DiscCap_Upload_01.xlsx Match; larger body
Automotive AC series YU7AC222M080 X1/Y2 Y2 300 Vac 80 Venatech_DiscCap_Upload_01.xlsx Match; automotive series
Reinforced insulation required YU0AH222M080 X1/Y1 Y1 250 Vac 80 Venatech_DiscCap_Upload_01.xlsx Match where Y1 is specified
Y1 at 400 Vac YU1AH222M080 X1/Y1 Y1 400 Vac 80 Venatech_DiscCap_Upload_01.xlsx Match; larger body
Incumbent is SMD S252B222K502 S2, X1/Y2 5000 Vdc SMD 2211 Venatech_MLCC_Upload_08.xlsx Mismatch in package; on our shelf in Hong Kong (snapshot 9 Nov 2026)

A Y1 part can replace a Y2 part electrically, but usually in a larger body, so check the hole pitch and clearance; a Y2 part never replaces a Y1. Our guide to disc capacitor safety classes AH, AC and AS decodes the series letters. The disc capacitor range page lists every family.

When should a heat pump design move from a disc to an SMD safety capacitor?

When the board is reflow-only and the value is small. Walsin lists 160 S2 safety MLCC in 1808, 1812, 2211 and 2220, X1/Y2 certified and rated 5,000 or 6,000 Vdc, from 3 pF to 10 nF; one of them, S252B222K502 at 2.2 nF, is on our shelf in Hong Kong (snapshot 9 Nov 2026).

An SMD safety capacitor removes a hand or wave-solder step, which matters on compact indoor-unit controllers. The trade is creepage: a radial disc gets its distance from its leads, while an SMD part depends on your pad spacing and any slot, so the board layout carries the safety argument. Larger across-the-line X values are usually film capacitors, outside this export. Request a quote for S2 or disc lines not on the snapshot and we source them through our authorised Walsin channel.

How Venatech helps: what can a Portuguese heat pump team send us?

Your EMI filter lines, and we return Walsin crosses class by class. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, including the 367 safety discs and 160 S2 safety MLCC counted here.

Paste a Y capacitor into the cross-reference tool or upload the filter BOM at /bom/, and we return the Walsin options with class, AC rating and body size stated against your part. Check the dated ready stock list and request a quote through the site. We serve Portugal from Hong Kong in small lots, which suits prototype and pilot builds, and we confirm availability and date code on each quote.

The short version

  • The Portugal News reported on 7 July 2026 that Bosch is investing at least eighty-five million euros in Portugal, including heat pump development and manufacturing in Aveiro.
  • X1/Y2 safety capacitor for basic insulation line to earth; X1/Y1 where the position bridges reinforced insulation; Y1 is tested at 8 kV, Y2 at 5 kV.
  • Walsin lists 367 safety discs: 186 X1/Y2 up to 10 nF and 181 X1/Y1 up to 4.7 nF, in 8 ratings.
  • At 2.2 nF there are 20 Walsin discs, and the S2 SMD part S252B222K502 is on our shelf in Hong Kong (snapshot 9 Nov 2026).

Send us the Y and X capacitor lines from your heat pump filter and we will return the Walsin crosses with every difference stated. Does your insulation diagram call for Y1 anywhere?

Related reading

Last reviewed: 16 November 2026

Sources

Fetched 16 November 2026.

  • The Portugal News, Bosch big bet on Portugal, 7 July 2026: https://www.theportugalnews.com/news/2026-07-07/boschs-85-million-big-bet-on-portugal-should-investors-follow/1051818
  • Bosch press release, Bosch increases heat pump production in Aveiro, Portugal, 6 November 2023: https://www.bosch-presse.de/pressportal/be/en/press-release-31040.html
  • TechOverflow, X1/X2/Y1/Y2/Y4 impulse withstand voltages (IEC 60384-14), 7 August 2019: https://techoverflow.net/2019/08/07/x1-x2-y1-y2-y4-impulse-withstand-rating-voltage-calculator-iec-60384-14/
  • Venatech upload files Venatech_DiscCap_Upload_01.xlsx and Venatech_MLCC_Upload_08.xlsx, and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.

Frequently asked questions

What is the difference between a Y1 and a Y2 capacitor?

Y1 is for positions bridging double or reinforced insulation and is impulse-tested at 8 kV; Y2 is for basic insulation and is tested at 5 kV, per IEC 60384-14. Your product standard decides which a position needs.

Can I use an X1/Y2 safety capacitor in a heat pump EMI filter?

Usually, for line-to-earth positions in earthed equipment with basic insulation. Walsin lists 186 X1/Y2 discs from 10 pF to 10 nF at 250, 300 and 500 Vac. Confirm the subclass with your compliance team.

What is the highest-value Walsin X1/Y1 disc capacitor?

4.7 nF in our count, across the AH and AS series, at Y1 ratings of 250, 400 and 500 Vac.

Which Walsin part crosses a 2.2 nF, 250 Vac Y2 disc capacitor?

YU0AC222M070 in the small-size AC series, or YU1AC222M070 for a 300 Vac Y2 rating. Check lead pitch and body size against your board.

Does Venatech have safety capacitors on the shelf in Hong Kong?

The S2 SMD safety MLCC S252B222K502, 2.2 nF, is on our shelf in Hong Kong (snapshot 9 Nov 2026). Disc lines are sourced on request through our authorised Walsin channel.

Can Venatech supply heat pump electronics makers in Portugal?

Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Portugal. Use the cross-reference tool or upload a BOM; confirm import rules with your compliance team.


Share This, Choose Your Platform!