NEWS

Shunt Resistor TCR for Battery Management in Belgium: 153 Walsin Metal Shunts at 50 ppm

Shunt resistor TCR sets how far a battery management system’s current reading drifts as the shunt heats. We counted 672 Walsin shunts at 10 milliohm or less: 638 metal plate or foil, and 153 rated 50 ppm per degree, from 3 milliohm up. Venatech is the authorised Walsin distributor in Hong Kong, serving Belgium.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for BMS, power-conversion and metering engineers, and their buyers, at battery storage integrators and electronics makers in Belgium. Walsin Technology (Walsin) is the line we are authorised for. On 16 November 2026 we parsed all 234,378 part numbers in our chip-resistor upload files, Venatech_ChipR_Upload_01.xlsx onward, filtered them to 10 milliohm or less, and grouped the result by temperature coefficient of resistance (TCR). Every part number below is real.

What is being built for battery storage in Belgium?

A 2.8 GWh battery in Limburg, among others. ESS News reported on 25 September 2026 that Giga Storage has started building Green Turtle, a 700 MW, 2.8 GWh four-hour battery on the Rotem industrial estate in Dilsen-Stokkem, with Tesla as EPC contractor supplying 640 Megapack 3 units and commissioning scheduled for the end of March 2028.

Those are the developer’s figures as reported, not ours, and the batteries in that project come with their supplier’s own electronics; we make no claim about what they use. The wider point for Belgian engineers is that grid storage is now a real local market: string monitors, auxiliary meters, inverter skids, test rigs and the smaller commercial systems that follow large projects all measure current through a milliohm shunt, and every one of those designs has to choose a TCR.

Why does shunt resistor TCR matter in a battery management system?

Because a hot shunt reads wrong. A shunt rated 70 ppm per degree that warms 50 degrees above its calibration point can shift by up to 3,500 ppm, which is 0.35 percent of reading; a thick-film shunt rated 1,000 ppm can shift 5 percent over the same rise.

That is our own arithmetic on the rated limits, not a measurement. In a BMS the error does not stay small: state-of-charge is integrated current, so a gain error that changes with load and ambient becomes a drifting charge estimate. Three choices control it. TCR, the subject here; self-heating, which is I squared times R, so 30 A through 2 milliohm dissipates 1.8 W in the part; and layout, because Kelvin sense traces keep copper, at roughly 3,900 ppm per degree, out of the measured path. Our explainer on what resistor TCR actually buys you covers the maths.

How many Walsin shunts at 10 milliohm or less reach 50 ppm?

153 of 672. We grouped all 672 distinct Walsin part numbers at 10 milliohm or less by rated TCR: 638 are metal plate or metal foil, of which 153 are rated 50 ppm, 358 at 70 ppm, 52 at 75 ppm and 74 at 100 ppm; the 50 ppm grade starts at 3 milliohm.

Value All Walsin parts At 50 ppm At 70 ppm At 75 ppm At 100 ppm
1 milliohm 48 0 26 15 7
2 milliohm 56 0 34 15 7
3 milliohm 64 8 40 4 12
5 milliohm 78 21 40 4 11
10 milliohm 111 32 40 4 5

The other 30 parts at 10 milliohm are thick film, at 250 ppm or wider. The 153 at 50 ppm split into 56 in the automotive metal-plate series, 41 metal foil, 32 metal-plate power and 24 standard metal plate, in sizes from 0306 to 2512. Below 3 milliohm the tightest grade is 70 ppm, so a 1 or 2 milliohm pack shunt is a 70 ppm decision. We have not seen this TCR split by value counted anywhere else.

Which Walsin shunts cross a 2512 BMS pack-current brief?

Several, depending on the value. For a 2512, 1 percent pack-current shunt, we shortlisted Walsin metal parts from 1 to 5 milliohm at 1 W to 3 W; at 3 and 5 milliohm the 50 ppm grade is available, including WW25NR003FTL at 2 W and the automotive WW25NR005FTLJ.

Brief: 2512, 1 percent, low TCR Walsin part Value Size Power TCR Export file Match / mismatch
Lowest value at 50 ppm WW25NR003FTL 3 milliohm 2512 2 W 50 ppm Venatech_ChipR_Upload_78.xlsx Match
Same, lower power WW25MR003FTL 3 milliohm 2512 1 W 50 ppm Venatech_ChipR_Upload_78.xlsx Match; check self-heating
Automotive grade WW25NR005FTLJ 5 milliohm 2512 2 W 50 ppm Venatech_ChipR_Upload_78.xlsx Match, automotive series
2 milliohm WW25KR002FTL 2 milliohm 2512 2 W 70 ppm Venatech_ChipR_Upload_78.xlsx Mismatch if the brief is 50 ppm; fits at 70 ppm
1 milliohm, high current WW25AR001FTL 1 milliohm 2512 3 W 70 ppm Venatech_ChipR_Upload_78.xlsx Match at 70 ppm, the tightest grade at 1 milliohm
Metal foil, long-side terminals WW25YR002FTL 2 milliohm 1225 2 W 100 ppm Venatech_ChipR_Upload_79.xlsx Mismatch in size and TCR; different footprint
Small cell-module shunt WW12YR005DTL 5 milliohm 0612 1 W 50 ppm Venatech_ChipR_Upload_77.xlsx Mismatch in size; adds 0.5 percent tolerance

Leave a column for your incumbent and compare pad layout as well as values, because metal-plate shunts from different makers rarely share a land pattern. Our guide to low-ohm current sense: thick film vs metal shows what changes between constructions. The chip resistor range page lists every Walsin family.

Is a thick-film shunt ever right for battery management?

For a coarse fault or overcurrent detect, yes; for coulomb counting, rarely. Walsin lists 34 thick-film shunts at 10 milliohm or less, all at 5 or 10 milliohm, and 32 of them are rated 200 ppm or wider, such as WW10WR010FTL at 600 ppm and WW06CR010FTL at 350 ppm.

A thick-film shunt is small and inexpensive to place, and a comparator tripping at twice rated current does not care about half a percent. A state-of-charge estimate does, which is why the metal families carry almost all the BMS work in Walsin’s range: 638 of the 672 low-value parts are metal. If your incumbent is a thick-film part in a measuring role, the cross is a TCR upgrade, and the footprint usually changes with it.

How Venatech helps: what can a Belgian BMS team send us?

Your shunt lines, and we return Walsin crosses with TCR stated. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, including the 672 Walsin shunts at 10 milliohm or less counted here.

Paste a shunt part into the cross-reference tool or upload the BMS or meter BOM at /bom/, and we return the Walsin options with value, power, TCR and size against your part. The ready stock page is a dated Hong Kong snapshot; for shunt lines not on it, request a quote and we source them through our authorised Walsin channel. We serve Belgium from Hong Kong in small lots, which suits prototypes and pilot builds, and we confirm availability and date code on each quote.

The short version

  • ESS News reported on 25 September 2026 that construction has started on Green Turtle, a 700 MW, 2.8 GWh battery in Dilsen-Stokkem, due for commissioning at the end of March 2028.
  • Shunt resistor TCR times temperature rise is the drift: 70 ppm over 50 degrees is up to 0.35 percent of reading.
  • Walsin lists 672 shunts at 10 milliohm or less; 638 are metal and 153 are rated 50 ppm, from 3 milliohm up.
  • At 1 and 2 milliohm the tightest Walsin grade is 70 ppm, in 2512 at up to 3 W.

Send us the shunt and sense-resistor lines from your BMS or meter and we will return the Walsin crosses with every difference stated. How far above calibration does your shunt run at full load?

Related reading

Last reviewed: 16 November 2026

Sources

Fetched 16 November 2026.

  • ESS News, Giga Storage starts construction on 2.8 GWh Belgian BESS, 25 September 2026: https://www.ess-news.com/2026/09/25/giga-storage-starts-construction-on-2-8-gwh-belgian-bess/
  • Venatech chip-resistor upload files Venatech_ChipR_Upload_01.xlsx onward (234,378 part numbers), re-measured 16 November 2026.

Frequently asked questions

What shunt resistor TCR do I need for a battery management system?

For coulomb counting, 50 to 75 ppm per degree is a common target, set by your accuracy budget and the shunt’s temperature rise. Walsin lists 153 shunts at 10 milliohm or less rated 50 ppm.

What is the lowest-value Walsin shunt rated 50 ppm?

3 milliohm, in 2512, for example WW25NR003FTL at 2 W and WW25MR003FTL at 1 W. Below 3 milliohm the tightest Walsin grade is 70 ppm.

Is a metal plate shunt better than thick film for BMS?

For measurement, generally yes, because of TCR: Walsin’s metal shunts at 10 milliohm or less run from 50 to 150 ppm, while 32 of its 34 thick-film parts there are 200 ppm or wider.

Which Walsin 1 milliohm shunt handles the most power?

In our export, 2512 metal-plate parts such as WW25AR001FTL are rated 3 W at 70 ppm. Confirm the power derating curve in Walsin’s datasheet.

Does Venatech hold Walsin shunts in Hong Kong?

Check the dated ready stock page. For shunt lines not on it, request a quote and we source them through our authorised Walsin channel, confirming availability on each quote.

Can Venatech supply BMS and storage electronics makers in Belgium?

Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Belgium. Use the cross-reference tool or upload a BOM; confirm import rules with your compliance team.


Share This, Choose Your Platform!