NEWS

Ferrite Bead for USB Peripherals and Power Boards in Vietnam: Lite-On Opens a 690 Million US Dollar Quang Ninh Plant and Walsin Lists 267 Chip Beads in 0402 and 0603

For a ferrite bead on USB peripheral and power boards built in Vietnam, Walsin Technology (Walsin) lists 267 chip beads in 0402 and 0603, and 104 of them are rated 1 A or more, up to 3 A. Venatech Limited, an authorised Walsin distributor in Hong Kong, crosses your beads and quotes them.


This post is for hardware and EMC engineers in northern Vietnam who lay out USB peripherals, docks and power boards, and for the buyers who source their filter parts. We counted the rows ourselves in Walsin’s inductor exports (Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx, 5,411 part numbers, 641 of them chip beads) and read the bead series against the datasheets named in the export. The news fact carries its source and date.

What did Lite-On open in Quang Ninh?

The first phase of a new electronics plant. Vietnam Investment Review reported on 13 November 2026 that Lite-On inaugurated the first phase of its Quang Ninh factory on 12 November, part of a project with total registered investment of 690 million US dollars on about 30 hectares at Song Khoai Industrial Park.

The report says phase one covers a building footprint of about 59,800 square metres and more than 214,000 square metres of floor space, planned as three manufacturing plants and an office. It names smart human-machine interface peripherals such as computer mice and keyboards among the products, alongside power solutions for data centres, with phase two planned for 2028 and the full project for 2030. Lite-On’s two existing Hai Phong factories employ more than 9,000 people, the report adds. We say nothing about the company’s suppliers. For an engineer in Vietnam, more peripheral and power-board assembly in the north means more boards that must pass EMC, and the ferrite bead is the cheapest filter on most of them.

Where does a ferrite bead sit on a USB peripheral or power board?

On every rail and line that carries noise off the board. A ferrite bead is a lossy chip inductor rated by its impedance at 100 MHz; on a USB peripheral it sits in series with VBUS and on supply rails, where it turns high-frequency noise into heat while passing DC with a small drop.

On a keyboard, mouse or dock the bead isolates the USB 5 V input from the controller and LED rails, keeps switching noise from the radio or the backlight driver off the cable, and filters supply pins on the MCU. On a power board the same part filters auxiliary and fan-controller rails. Two numbers drive the choice: impedance at the frequency you need to suppress, and the rated current with the DC resistance that comes with it. Our guide to ferrite bead vs inductor impedance at 100 MHz explains why a bead is specified differently from an inductor, and the inductor range lists every part.

How many Walsin ferrite beads are there in 0402 and 0603, and at what current?

Two hundred and sixty-seven. We counted 267 distinct Walsin chip beads in 0402 and 0603 across nine series: 90 in 0402 and 177 in 0603; 104 are rated 1 A or more and 48 reach 2 A or more.

Case size Below 0.5 A 0.5 A to 0.99 A 1 A to 1.99 A 2 A or more Total
0402 (1005) 53 16 11 10 90
0603 (1608) 47 47 45 38 177
Total 100 63 56 48 267

The 104 parts at 1 A or more come from the WLBD(HC) series (31), the MHC-S and MHC-P series (29) and Walsin’s automotive MCB / MHC series (38), with 6 more in WQBD; the plain MCB families carry the lower currents at higher impedance. Across all sizes Walsin lists 641 chip beads, so 0402 and 0603 hold well over a third of the range.

Which Walsin ferrite bead fits a 120 ohm, 1 A USB VBUS brief?

Five parts meet it. For a brief of 120 ohm at 100 MHz, 1 A or more, 0402 or 0603, MHC1005S121MBP, WLBD1005HCU121TL, MHC1608S121NBP, MHC1608S121QBP and WLBD1608HCU121TL match.

Put your incumbent bead in the last column and compare each field.

Walsin part Case Impedance at 100 MHz DCR (max) Rated current Match / mismatch with 120 ohm, 1 A or more, 0402 or 0603 Your incumbent
MHC1005S121MBP 0402 120 ohm 0.15 ohm 1.5 A Match
WLBD1005HCU121TL 0402 120 ohm 0.055 ohm 2 A Match, lower drop
MHC1608S121NBP 0603 120 ohm 0.09 ohm 2 A Match
MHC1608S121QBP 0603 120 ohm 0.04 ohm 3 A Match, headroom for USB-C 3 A
WLBD1608HCU121TL 0603 120 ohm 0.03 ohm 3 A Match, headroom for USB-C 3 A
MCB1005S121IBP 0402 120 ohm 0.4 ohm 600 mA Mismatch: current below 1 A
MCB1608S121IBP 0603 120 ohm 0.15 ohm 600 mA Mismatch: current below 1 A
MHC1608S601LBP 0603 600 ohm 0.2 ohm 1 A Mismatch on impedance; fits a low-current supply pin

Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.

Beads with the same impedance at 100 MHz can behave very differently at 30 MHz or 1 GHz, so compare the full impedance curve, not just the headline figure.

Check the datasheet. Impedance against frequency, and how impedance falls as DC current rises, are plotted on each series datasheet, not in the export. Read both curves at your real load current before you sign off an EMC fix.

How much voltage does a ferrite bead drop on a USB rail?

Current times DCR, which is small but not zero. At 1.5 A, WLBD1005HCU121TL with 0.055 ohm maximum DCR drops at most about 83 mV, while MHC1005S121MBP with 0.15 ohm drops up to 225 mV in the same 0402 footprint.

USB specifies a minimum VBUS at the device, and a long cable already eats into it, so a bead that drops a quarter of a volt can push a bus-powered dock or a backlit keyboard close to the edge. The same DCR turns into heat: 1.5 A through 0.15 ohm is about 0.34 W in an 0402 body. Choosing a high-current series with lower DCR costs nothing in footprint and buys margin on both counts. Our note on ferrite bead cross-reference covers what else to compare when you swap brands.

Can Venatech supply Walsin ferrite beads from Hong Kong?

Yes, to order. All 267 Walsin chip beads in 0402 and 0603 can be quoted from Hong Kong; none is on our shelf in Hong Kong (snapshot 9 Nov 2026), so request a quote and we source them through our authorised Walsin channel.

We checked all 267 codes against that snapshot. Each quote states availability, date code and lead time for the line, and we work in small lots for EMC iterations and pilot builds. We make no stock, price or lead-time promise. The ready-stock list is a dated snapshot of the MLCC and chip resistors that sit beside the beads on the same board.

How Venatech helps: what should a Vietnamese board team send us?

The beads and filter parts from your BOM. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.

Paste a bead code into the cross-reference tool, or upload the whole BOM and request a quote through the site; add the load current on each rail so we check DCR as well as impedance. The ready-stock snapshot is dated 9 November 2026. We serve Quang Ninh, Hai Phong, Bac Ninh and Bac Giang from Hong Kong, with fast quotes and small lots. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.

The short version

Lite-On opened the first phase of its Quang Ninh plant on 12 November 2026, a project with 690 million US dollars of registered investment covering peripherals and data-centre power, Vietnam Investment Review reported on 13 November 2026. Every USB peripheral and power board filters its rails with ferrite beads. Walsin lists 267 chip beads in 0402 and 0603, 104 rated 1 A or more, and WLBD1608HCU121TL meets a 120 ohm, 3 A USB-C brief in 0603.

Send us the beads on your peripheral or power board with the rail currents, and we will return Walsin crosses with every difference stated. Which rail failed your last EMC scan?

Related reading

Last reviewed: 19 November 2026.

Sources

Fetched 19 November 2026.

  • Vietnam Investment Review, report on Lite-On’s Quang Ninh factory, 13 November 2026: https://vir.com.vn/lite-on-opens-first-phase-of-quang-ninh-factory-165071.html
  • Walsin inductor exports, Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx, re-measured 19 November 2026; Walsin bead series datasheets as named in the export; Venatech Hong Kong stock snapshot dated 9 November 2026.

Frequently asked questions

What did Lite-On open in Quang Ninh in November 2026?

Vietnam Investment Review reported that Lite-On inaugurated phase one of its Quang Ninh factory on 12 November 2026, part of a 690 million US dollar registered project making peripherals such as mice and keyboards and data-centre power solutions.

What does a ferrite bead do on a USB peripheral?

It sits in series with VBUS and supply rails and absorbs high-frequency noise as heat while passing DC with a small voltage drop. It is rated by impedance at 100 MHz, rated current and DCR.

How many Walsin ferrite beads are available in 0402 and 0603 for buyers in Vietnam?

We counted 267: 90 in 0402 and 177 in 0603. 104 are rated 1 A or more and 48 reach 2 A or more.

Which Walsin ferrite bead crosses a 120 ohm 3 A 0603 bead?

WLBD1608HCU121TL and MHC1608S121QBP match at 120 ohm and 3 A in 0603. Check the impedance curve at your load current before release.

How do I calculate the voltage drop across a ferrite bead?

Multiply load current by the maximum DCR. At 1.5 A, a 0.055 ohm bead drops about 83 mV and a 0.15 ohm bead about 225 mV.

Is Venatech an authorised Walsin distributor for buyers in Vietnam?

Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Vietnam in small lots. Stackpole and Viking are lines we supply, not authorised lines.


Share This, Choose Your Platform!