NEWS

Standby Power Regulations in the UK: Off Mode Falls to 0.3 W in the 2026 Consultation, and 624 Walsin 1206 High-Voltage Resistors from 1 to 4.7 MΩ for Bleeders

New standby power regulations proposed for Great Britain would cut the off-mode limit from 0.5 W to 0.3 W; the consultation closes on 24 December 2026. The bleeder across your X capacitor now matters. Walsin Technology (Walsin) lists 624 high-voltage 1206 resistors from 1 to 4.7 MΩ. Venatech is the authorised Walsin distributor in Hong Kong.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for power-supply designers, and the buyers who support them, at appliance, consumer electronics, IT and external power supply makers selling into the UK. This is engineering perspective on a draft rule, not legal or compliance advice: which of your products fall in scope, and from when, is a question to confirm with your compliance team. What a lower off-mode limit does is shrink the budget for every milliwatt a mains input stage burns with the product switched off, and a resistor that sits across the mains all the time is one of the easiest places to find a few. On 18 November 2026 we re-measured Walsin’s chip-resistor export (Venatech_ChipR_Upload_01.xlsx onward, 234,378 part numbers) against our ready-stock snapshot dated 9 November 2026.

What do the proposed UK standby power regulations change?

Lower limits and wider scope. The Department for Energy Security and Net Zero published its consultation on 16 October 2026, proposing to replace Regulations 1275/2008 and 107/2009 for Great Britain with one ecodesign regulation aligned with EU Regulation 2023/826; responses close at 11:59pm on 24 December 2026.

LexisNexis summarised the proposals on 19 October 2026: off mode would fall from 0.5 W to 0.3 W, standby with an information or status display from 1.0 W to 0.8 W, and networked standby would be set at 7 W for high network availability equipment and 2 W for other networked products. Most equipment would have to drop to a low-power mode after 20 minutes of inactivity, with exceptions, and coverage would widen to include motor-operated furniture, devices with low-voltage external power supplies, certain rechargeable products and simple set-top boxes. The gov.uk page, last updated on 22 October 2026 when the draft regulations were added, does not state an implementation date, so we give none.

Where does a mains power supply lose power in off mode?

In anything connected before the switch. A resistor across 230 V dissipates V²/R all the time: 53 mW at 1 MΩ, 24 mW at 2.2 MΩ and 11 mW at 4.7 MΩ, so a 1 MΩ bleeder alone uses about 18 percent of a 0.3 W off-mode budget.

That figure is our arithmetic, not the consultation’s. The usual culprits are the X capacitor discharge resistors, the start-up resistor for the controller, any voltage-sense divider on the bus, the idle current of the controller itself and the leakage of the bulk capacitor. Raising the bleeder value is the cheap fix, but it lengthens the discharge time constant: with a 0.47 µF X capacitor, 1 MΩ gives about 0.47 s and 4.7 MΩ about 2.2 s. Your safety standard sets the discharge time you must meet after unplugging, so the value is a trade-off rather than a free choice. Where a discharge IC is not an option, value and voltage rating are the two levers.

Bleeder value at 230 V Dissipation (V²/R) Share of 0.3 W Time constant with 0.47 µF
1 MΩ 53 mW 18 % 0.47 s
2.2 MΩ 24 mW 8 % 1.03 s
3.3 MΩ 16 mW 5 % 1.55 s
4.7 MΩ 11 mW 4 % 2.21 s

How many Walsin high-voltage 1206 resistors sit between 1 and 4.7 MΩ?

Six hundred and twenty-four part numbers. We parsed Walsin’s chip-resistor export and counted 20,244 distinct high-voltage thick-film parts; 624 of them are 1206 and between 1 MΩ and 4.7 MΩ, in four series, all listed at 0.25 W.

Walsin series (export name) Part numbers, 1206, 1 to 4.7 MΩ
Thick Film High Voltage Chip Resistor 265
Thick Film High Voltage Chip Resistor (Automotive) 171
Thick Film High Voltage Chip Resistor UL Safety Certification 94
Thick Film High Voltage Chip Resistor UL Safety Certification (Automotive) 94
Total 624

By tolerance, 385 are ±1 percent, 77 are ±0.5 percent, 77 are ±2 percent and 85 are ±5 percent. We have not seen this cut counted anywhere else. The export does not carry a working-voltage column, so check the datasheet: Walsin’s ASC_WFxxV.pdf, ASC_WFxxN.pdf and ASC_WKxxV.pdf give the maximum working and overload voltages per case size, and that is the figure that decides whether one 1206 part can stand across the line or whether you need two in series. The UL Safety Certification series names describe Walsin’s own approvals; read the certificate scope on Walsin’s documents before relying on it. The chip resistor range lists every family.

Which bleeder resistor fits a 0.3 W off-mode budget?

A high-voltage part at the highest value your discharge time allows. Against a brief of 2 MΩ or more, a high-voltage series, ±1 percent and 1206, 5 of the 7 Walsin parts below match; the 1 MΩ part misses on dissipation and the shelf part misses on series.

Walsin part Value Tolerance Series Match / mismatch for a 1206 high-voltage bleeder, 2 MΩ or more Your incumbent
WF12V2204FTL 2.2 MΩ ±1 % High Voltage Match
WF12V4704FTL 4.7 MΩ ±1 % High Voltage Match, lowest loss; check discharge time
WF12N2004FTL 2 MΩ ±1 % High Voltage UL Safety Certification Match
WF12N2004FTLJ 2 MΩ ±1 % High Voltage UL Safety Certification (Automotive) Match, AEC-Q200 tagged
WK12V3304FTL 3.3 MΩ ±1 % High Voltage Match
WF12V1004FTL 1 MΩ ±1 % High Voltage Mismatch: 53 mW at 230 V; use two in series or a higher value
WR08X1004FTL 1 MΩ ±1 % General Purpose, 0805 Mismatch: not a high-voltage series; on our shelf

Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.

Put your incumbent in the last column, confirm voltage ratings against both datasheets, and measure off-mode power on the finished product. Our note on high-voltage chip resistors and the limit nobody checks explains why the voltage rating, not the power rating, is usually the binding limit here.

Which high-value resistors are on the shelf in Hong Kong?

Six general-purpose lines at 1 MΩ or more. We checked the 624 parts, and every Walsin resistor at 1 MΩ or more, against our ready-stock snapshot dated 9 November 2026: six general-purpose lines in 0402, 0603 and 0805 are on our shelf in Hong Kong, including WR06X1004FTL and WR08X1004FTL at 1 MΩ.

The other four are WR04X1004FTL, WR04W1504FTL, WR04W2704FTL and WR04W3304FTL. On our shelf in Hong Kong (snapshot 9 November 2026) means held on that date, not a promise of quantity or date code today. The 624 high-voltage 1206 parts are to order: request a quote and we source them through our authorised Walsin channel, confirming availability, date code and lead time on each quote.

How Venatech helps

How Venatech helps is a checked cross before your next design review. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, so a list of incumbent bleeder, start-up and sense resistors returns Walsin candidates with each difference stated.

Paste your resistor part numbers into the cross-reference tool, or upload the input-stage BOM and request a quote through the site. The ready-stock snapshot, dated 9 November 2026, lists the resistors on our shelf in Hong Kong. We are Hong Kong-based, supply UK buyers in small lots, and confirm availability, date code and lead time on every quote. Walsin is our authorised line; Stackpole and Viking are lines we supply. For scope and dates under the new regulations, confirm with your compliance team.

The short version

DESNZ proposes new standby power regulations for Great Britain that would lower off mode from 0.5 W to 0.3 W and standby with a display from 1.0 W to 0.8 W; the consultation closes on 24 December 2026. A 1 MΩ bleeder across 230 V burns about 53 mW, nearly a fifth of that budget. Walsin lists 624 high-voltage 1206 resistors from 1 MΩ to 4.7 MΩ, 188 of them in its UL Safety Certification series; six general-purpose resistors at 1 MΩ or more were on our Hong Kong shelf on 9 November 2026.

Send us the mains input stage of your current power supply, and we will return Walsin crosses for every resistor with value, series and case stated. Which resistor on that board runs hottest in off mode?

Related reading

Last reviewed: 18 November 2026

Sources

Fetched 18 November 2026.

  • GOV.UK, Department for Energy Security and Net Zero, “Updating standards for standby, networked standby and off mode power consumption”, published 16 October 2026, updated 22 October 2026: https://www.gov.uk/government/consultations/updating-standards-for-standby-networked-standby-and-off-mode-power-consumption
  • LexisNexis, “DESNZ consults on updated ecodesign standards for standby, networked standby, off mode power”, 19 October 2026: https://www.lexisnexis.co.uk/legal/news/desnz-consults-on-updated-ecodesign-standards-for-standby-networked-standby-off-mode-power
  • Walsin chip-resistor export, Venatech_ChipR_Upload_01.xlsx onward, re-measured 18 November 2026; Walsin datasheets ASC_WFxxV.pdf, ASC_WFxxN.pdf, ASC_WKxxV.pdf and ASC_WR.pdf; Venatech ready-stock snapshot dated 9 November 2026.

Frequently asked questions

<!– wp:rank-math/faq-block {"questions":[{"id":"faq-question-01","title":"What off-mode limit do the proposed UK standby power regulations set?","content":"LexisNexis reported on 19 October 2026 that DESNZ proposes cutting the off-mode limit from 0.5 W to 0.3 W, and standby with a display from 1.0 W to 0.8 W, for products sold in Great Britain.","visible":true},{"id":"faq-question-02","title":"When does the UK standby power consultation close?","content":"The GOV.UK page says responses close at 11:59pm on 24 December 2026. It does not give an implementation date; confirm timing with your compliance team.","visible":true},{"id":"faq-question-03","title":"How much power does an X capacitor discharge resistor waste?","content":"A resistor across 230 V dissipates V²/R: about 53 mW at 1 MΩ, 24 mW at 2.2 MΩ and 11 mW at 4.7 MΩ. Higher values lengthen the discharge time, so check it against your safety standard.","visible":true},{"id":"faq-question-04","title":"How many Walsin high-voltage 1206 resistors are between 1 MΩ and 4.7 MΩ?","content":"We counted 624 distinct part numbers in four high-voltage series, 385 of them at ±1 percent and 188 in the UL Safety Certification series, all listed at 0.25 W.","visible":true},{"id":"faq-question-05","title":"Are high-value Walsin resistors in stock in Hong Kong for UK buyers?","content":"Six general-purpose lines at 1 MΩ or more, such as WR06X1004FTL, were on our shelf in Hong Kong in the snapshot dated 9 November 2026. The high-voltage 1206 parts are quoted through our authorised Walsin channel.”,”visible”:true},{“id”:”faq-question-06″,”title”:”Is Venatech an authorised Walsin distributor for buyers in the UK?”,”content”:”Venatech Limited is an authorised Walsin distributor in Hong Kong and supplies UK buyers in small lots. Stackpole and Viking are lines we supply, not authorised lines.”,”visible”:true}],”listStyle”:””,”titleWrapper”:”h3″,”titleCssClasses”:””,”contentCssClasses”:””,”sizeSlug”:””} –>

What off-mode limit do the proposed UK standby power regulations set?

LexisNexis reported on 19 October 2026 that DESNZ proposes cutting the off-mode limit from 0.5 W to 0.3 W, and standby with a display from 1.0 W to 0.8 W, for products sold in Great Britain.

When does the UK standby power consultation close?

The GOV.UK page says responses close at 11:59pm on 24 December 2026. It does not give an implementation date; confirm timing with your compliance team.

How much power does an X capacitor discharge resistor waste?

A resistor across 230 V dissipates V²/R: about 53 mW at 1 MΩ, 24 mW at 2.2 MΩ and 11 mW at 4.7 MΩ. Higher values lengthen the discharge time, so check it against your safety standard.

How many Walsin high-voltage 1206 resistors are between 1 MΩ and 4.7 MΩ?

We counted 624 distinct part numbers in four high-voltage series, 385 of them at ±1 percent and 188 in the UL Safety Certification series, all listed at 0.25 W.

Are high-value Walsin resistors in stock in Hong Kong for UK buyers?

Six general-purpose lines at 1 MΩ or more, such as WR06X1004FTL, were on our shelf in Hong Kong in the snapshot dated 9 November 2026. The high-voltage 1206 parts are quoted through our authorised Walsin channel.

Is Venatech an authorised Walsin distributor for buyers in the UK?

Venatech Limited is an authorised Walsin distributor in Hong Kong and supplies UK buyers in small lots. Stackpole and Viking are lines we supply, not authorised lines.


Share This, Choose Your Platform!