A current sense resistor gives a mining motor drive its view of phase and bus current. For drive makers serving British Columbia, Canada, Walsin lists 54 metal plate shunts at 3 W in 2512, 1 percent, from 1 to 20 milliohm, covering both Stackpole CSSH2512 ranges. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for power electronics engineers and buyers at Canadian makers of motor drives, conveyor and hoist controls, battery-electric mining equipment and the power electronics that serve British Columbia’s mines. Walsin Technology (Walsin) is the line we are authorised for; Stackpole Electronics (SEI) is a line we supply, so a CSSH2512 already on your parts list can be quoted as it is or crossed to Walsin. We measured every Walsin figure below on 16 November 2026 in our Walsin current sense export, Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx, and checked our ready stock snapshot dated 9 November 2026. Stackpole figures come only from Stackpole’s resistors-for-medical-applications release of 2 May 2019 on seielect.com, fetched the same day; the CSSH datasheet did not load for us that day, so confirm each Stackpole figure against it.
What did British Columbia approve at Red Chris in June 2026?
Key permits for a 31-year underground block cave. North of 60 Mining News reported on 22 June 2026 that British Columbia had granted key approvals for the Red Chris block cave, a 70-30 Newmont and Imperial Metals joint venture, with more than 1,800 construction jobs and about 1,500 operating roles.
The same report said the prefeasibility study gives 31 years of operations, averaging about 107 million pounds of copper a year, and that the project is expected to lift Canada’s copper production by about 15 percent, with a final investment decision expected later in 2026. The Narwhal reported on 17 February 2026 that British Columbia hosts 16 of the 34 minerals and metals Canada lists as critical. Those are the publications’ figures, not ours. An underground block cave runs on motors: ventilation fans, conveyors, crushers, hoists, pumps and, at some sites, battery-electric loaders, and every one of them has a drive that measures current.
Where does a current sense resistor sit in a mining motor drive?
In the DC link or phase legs. A drive senses current through a low-ohm metal shunt in the DC link, the low-side leg or the phase output, and the controller reads the millivolt drop for current control, overcurrent trip and short-circuit shutdown; battery-electric equipment does the same in its battery management system.
The value trades signal against loss. By the square-root-of-power-over-resistance rule, a 3 W shunt reaches about 54.8 A at 1 milliohm, 24.5 A at 5 milliohm and 12.2 A at 20 milliohm. That covers auxiliary drives, fan and pump inverters, gate-driver supplies and battery modules; the main traction and hoist drives at hundreds of amps usually sense through a bolt-on shunt or Hall sensor instead. In a mine, temperature swings and vibration are the real stresses, so TCR and solder-joint reliability decide the choice as much as power. Our low-ohm current sense: thick film versus metal note explains why metal is the default at these values.
How many Walsin 3 W 2512 shunts run from 1 to 20 milliohm?
- We filtered Walsin’s metal plate current sense rows to 2512, 3 W and 1 percent between 1 and 20 milliohm and counted 54 distinct part numbers at 16 values; 27 carry the automotive tag and 14 are 50 ppm parts, the rest 70 ppm.
| Range | Walsin parts at 3 W, 1 percent | Values | TCR (export) | Example |
|---|---|---|---|---|
| 1 to 5 milliohm | 20 | 1, 2, 3, 4, 5 | 70 ppm | WW25AR001FTL, WW25BR005FTL |
| 5 to 10 milliohm | 24 | 5 to 10 in 1 milliohm steps | 70 ppm | WW25AR010FTL |
| 12 to 20 milliohm | 14 | 12, 14, 15, 16, 18, 20 | 50 ppm | WW25AR020FTL |
The 5 milliohm parts sit in both of the first two rows, which is why the rows add to more than 54. Each value comes as a general part and an automotive part, for example WW25AR001FTL and WW25AR001FTLJ. We have not seen this 3 W, 1 to 20 milliohm cell counted elsewhere. Our export has no current column, so the amps above come from the power-and-resistance rule; confirm them in Walsin’s datasheet.
Which Walsin parts cross a Stackpole CSSH2512 shunt?
On size, power and tolerance, across both ranges. Stackpole’s release of 2 May 2019 describes CSSH2512 as a 3 W, 2512, 1 percent current sense resistor with good TCR, used from 1 to 5 milliohm in mobility motor drives and 5 to 20 milliohm in bed motor control, naming CSSH2512FT5L00 at 5 milliohm.
| Your brief (CSSH2512 style) | Walsin part | Walsin size, power, TCR (export) | Match / mismatch | Your incumbent |
|---|---|---|---|---|
| 1 milliohm, 1 percent, 3 W | WW25AR001FTL |
2512, 3 W, 70 ppm | Match on size, value, power, tolerance; TCR: compare to your datasheet | |
| 5 milliohm, 1 percent, 3 W, like CSSH2512FT5L00 | WW25BR005FTL |
2512, 3 W, 70 ppm | Match on size, value, power, tolerance; CSSH2512FT5L00 itself is not in our Walsin export, so cross it here | |
| 10 milliohm, 1 percent, 3 W | WW25AR010FTL |
2512, 3 W, 70 ppm | Match on size, value, power, tolerance | |
| 20 milliohm, 1 percent, 3 W | WW25AR020FTL |
2512, 3 W, 50 ppm | Match on size, value, power, tolerance and the 50 ppm class | |
| Footprint and terminal style | any of the above | 2512 body; pad layout not stated in our export | Mismatch possible on pad geometry: compare land patterns |
What should a Canadian mining electronics team check before switching shunts?
TCR over the full temperature range, then the solder joint. Check the TCR against the drive’s cold-start and full-load temperatures, the solder-joint life on the 2512 pads under vibration, then the pulse rating for short-circuit trips; 70 ppm over a 60 degree rise is a 0.42 percent shift.
British Columbia equipment can start well below freezing and run hot under load, so the temperature span is wide. Keep Kelvin sense routing on the new footprint. Ask for the qualification report on automotive parts; Walsin’s datasheets say compliant and Venatech makes no qualification claim of its own. Mining equipment carries its own safety approvals; we give no certification or compliance advice, so confirm with your compliance team. Our current sense resistor TCR note covers the TCR side, and our Canadian industrial and cold-climate note covers the cold side.
How Venatech helps
Cross the drive board in one paste. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating size, value, tolerance, TCR and power as match or mismatch.
Paste your shunt lines into the cross-reference tool, or upload the parts list at BOM upload. On our shelf in Hong Kong (snapshot 9 Nov 2026) are three Walsin thick film current sense lines in 0805, WW08WR270FTL, WW08WR390FTL and WW08WR470FTL, at 0.27, 0.39 and 0.47 ohm, 1 percent, 1/4 W, suited to auxiliary and gate-driver supply sensing; see ready stock. The 3 W metal shunts are not on it, so request a quote and we source them through our authorised Walsin channel. Stackpole CSSH2512 lines can be quoted too; Stackpole is a line we supply, and Walsin is the line we are authorised for. We serve Canadian buyers from Hong Kong in small lots and confirm availability, date code and lead time on each quote, with no price, lead-time or stock guarantee. The chip resistor range lists every Walsin family.
The short version
- British Columbia granted key approvals for the 31-year Red Chris block cave, per North of 60 Mining News on 22 June 2026, with more than 1,800 construction jobs.
- Walsin lists 54 metal plate shunts at 3 W, 2512 and 1 percent from 1 to 20 milliohm; 27 are automotive and 14 are 50 ppm.
- Both Stackpole CSSH2512 ranges, 1 to 5 and 5 to 20 milliohm, have Walsin matches on size, value, power and tolerance.
- Check TCR across your temperature span and the pad layout before you switch.
Send us the shunt lines from your drive or battery board, and we will return the Walsin crosses with every difference stated. What is the coldest start your drive has to survive?
Related reading
- Low-ohm current sense: thick film versus metal
- Current sense resistor TCR
- Walsin resistors for Canadian industrial and cold-climate electronics
- Cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 16 November 2026.
Sources
Fetched 16 November 2026.
- North of 60 Mining News, “BC okays key Red Chris block cave permits”, 22 June 2026: https://www.miningnewsnorth.com/story/2026/06/26/northern-neighbors/bc-okays-key-red-chris-block-cave-permits/9737.html
- The Narwhal, “B.C.’s critical minerals push to reshape the province”, 17 February 2026: https://thenarwhal.ca/bc-mining-push-2026/
- Stackpole Electronics release on resistors for medical applications, 2 May 2019: https://seielect.com/news/20190502_Resistors_for_Medical_Applications.pdf
- Venatech Walsin current sense export (Metal_Low_Ohm_Current_Sense_Chip_Resistor__1of1.xlsx) and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.
Frequently asked questions
What current sense resistor suits a mining fan or pump drive in British Columbia?
It depends on the phase or bus current and the controller’s input range. A 3 W, 2512 metal shunt reaches about 24.5 A at 5 milliohm and 12.2 A at 20 milliohm by the power-and-resistance rule; size it with margin and confirm in the datasheet.
How many Walsin 3 W 2512 shunts are there from 1 to 20 milliohm?
54 in our export at 1 percent, at 16 values: 27 automotive, 14 at 50 ppm from 12 to 20 milliohm and the rest at 70 ppm.
Which Walsin part crosses a Stackpole CSSH2512 at 5 milliohm?
WW25BR005FTL, a 2512, 5 milliohm, 1 percent, 3 W metal plate part at 70 ppm in our export, or WW25AR005FTLJ for the automotive version. Compare TCR and pad layout before you approve it.
Is there a 50 ppm Walsin 3 W shunt for Canadian mining equipment?
Yes. Fourteen Walsin 3 W, 2512, 1 percent parts are 50 ppm, from 12 to 20 milliohm, for example WW25AR020FTL.
Do you hold current sense resistors in stock in Hong Kong?
Three Walsin 0805 thick film current sense lines are on our shelf in Hong Kong (snapshot 9 Nov 2026), at 0.27, 0.39 and 0.47 ohm. The 3 W metal shunts are not; request a quote and we source them through our authorised Walsin channel.
Is Venatech authorised for Stackpole?
No. Venatech is the authorised Walsin distributor in Hong Kong; Stackpole is a line we supply, and we quote Stackpole CSSH2512 lines alongside the Walsin cross.