A soft termination MLCC puts a flexible polymer layer under the plating, so board bending and vibration crack the termination rather than the ceramic. Walsin lists 83 soft termination MLCC at 100 nF, from 0402 to 2225 and 10 V to 1,500 V, 14 of them AEC-Q200. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for hardware and component engineers in Abu Dhabi and the wider UAE who build rugged boards for defence, security and industrial systems. Walsin Technology (Walsin) is the line we are authorised for. We parsed our MLCC upload files, Venatech_MLCC_Upload_01.xlsx to Venatech_MLCC_Upload_08.xlsx, on 16 November 2026, filtered them to the SH, SG and ST soft termination series and counted distinct part numbers at 100 nF. We then checked the result against our ready stock snapshot dated 9 November 2026. Every part number below is real.
What did EDGE and ICAPE agree in Abu Dhabi in May 2026?
A memorandum to explore local supply of printed circuit boards and electronic subsystems. The Arabian Post reported on 5 May 2026 that EDGE Group and ICAPE Group signed an MoU at Make it in the Emirates 2026 in Abu Dhabi covering PCBs, turnkey electronics and custom components, and that EDGE says more than 80 percent of its systems are made in the UAE.
The same report notes that the MoU is a step beyond an existing commercial relationship, not a finished supply contract, and it quotes EDGE’s figure of 7.96 billion US dollars in 2025 order intake. Those are EDGE’s and the publication’s figures, not ours. What matters for a component engineer is the direction: more of the board-level work behind Abu Dhabi’s defence and security systems is being built in the UAE, and that work needs approved, documented passives for boards that see vibration, shock and wide temperature swings.
Why do defence boards in the UAE specify a soft termination MLCC?
Because flex cracking is one of the commonest MLCC failures and it hides until the field. A ceramic capacitor is brittle; when a board bends during depanelling, screw-down, connector insertion or vibration, a crack can start under a standard termination, and a soft termination MLCC moves that stress into a polymer layer instead.
The crack in a standard part often passes electrical test and fails later as leakage or a short, which is the outcome a rugged design most wants to avoid. Larger case sizes and parts near board edges, mounting holes or heavy connectors are most exposed. Soft termination does not change the capacitance or the dielectric; it changes how the part survives mechanical strain. Walsin builds it two ways: SH with a silver-polymer layer and SG with a copper-polymer layer, plus ST, an automotive soft termination series qualified to AEC-Q200. Our guides to flex cracking and board bend and Walsin’s SH, SG, ST and VT series cover the mechanism.
How many 100 nF soft termination MLCC does Walsin list?
- We counted 83 distinct Walsin soft termination MLCC at 100 nF: 64 in SH, 5 in SG and 14 in the AEC-Q200 ST series; 75 are X7R, 6 C0G and 2 X5R, and the rated voltage climbs with case size from 25 V in 0402 to 1,500 V in 2225.
| Case size | Parts at 100 nF | Lowest rating | Highest rating |
|---|---|---|---|
| 0402 | 7 | 10 V | 25 V |
| 0603 | 14 | 10 V | 100 V |
| 0805 | 13 | 10 V | 200 V |
| 1206 | 19 | 10 V | 450 V |
| 1210 | 13 | 25 V | 630 V |
| 1812 | 9 | 100 V | 1,000 V |
| 1825 | 6 | 100 V | 1,000 V |
| 2220 | 1 | 1,000 V | 1,000 V |
| 2225 | 1 | 1,500 V | 1,500 V |
So a 100 nF decoupling or filter position can stay in soft termination from a 0402 logic rail up to a 1,000 V or 1,500 V high-voltage stage. Across all three series our extract holds 1,653 soft termination part numbers. We have not seen the 100 nF slice counted anywhere else.
Which Walsin parts cross a 100 nF, 50 V, 0603 X7R soft termination brief?
Four soft termination parts match at 10 percent or tighter. At 100 nF, 50 V, 0603 and X7R, we found SH, SG and ST soft termination parts that match, plus standard and AEC-Q200 parts that match the value but not the termination.
| Brief: 100 nF, 50 V, X7R, 0603 | Walsin part | Series | Match / mismatch | Your incumbent |
|---|---|---|---|---|
| Silver-polymer soft termination, 10 percent | SH18B104K500 |
SH | Match; on our Hong Kong shelf | |
| Same, 5 percent | SH18B104J500 |
SH | Match, tighter tolerance | |
| Copper-polymer soft termination | SG18B104K500 |
SG | Match | |
| Soft termination plus AEC-Q200 | ST18B104K500 |
ST | Match, adds AEC-Q200 | |
| Soft termination plus AEC-Q200, 20 percent | ST18B104M500 |
ST | Mismatch in tolerance | |
| AEC-Q200, standard termination | MT18B104K500 |
MT | Mismatch: no soft termination | |
| General purpose | 0603B104K500 |
General Purpose | Mismatch: no soft termination |
Leave the last column for your current part. Check thickness and land pattern against both datasheets before you swap, as our post on how to cross-reference an MLCC explains. The X7R value will also fall under DC bias; see MLCC DC bias and voltage derating.
Which Walsin soft termination MLCC are on the Hong Kong shelf?
Twenty-nine lines. We checked all 1,653 Walsin soft termination part numbers against our ready stock snapshot dated 9 November 2026: 29 SH lines are on our shelf in Hong Kong (snapshot 9 Nov 2026), including SH18B104K500 at 100 nF, SH31B475K500 at 4.7 uF and SH55B684K631 at 680 nF and 630 V.
The 29 run from 0402 to 2220 and from 25 V to 3 kV, among them SH32B335K500 at 3.3 uF in 1210 and SH42N101J302, a 100 pF C0G part in 1808 rated 3 kV. SG and ST lines are not on the snapshot: request a quote and we source them through our authorised Walsin channel. The ready stock list is a dated snapshot, and the MLCC range page shows every series. We confirm availability, date code and lead time on each quote and promise none in advance.
How Venatech helps: what can we cross for an Abu Dhabi electronics team?
The whole capacitor list, in one pass, with every difference stated. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, and 29 soft termination lines sit on our Hong Kong shelf snapshot dated 9 November 2026.
Paste the MLCC lines into the cross-reference tool and filter for soft termination, or upload the full BOM at /bom/ and request a quote through the site. We work from Hong Kong in small lots, which suits prototype and qualification builds, and we quote fast. Export-control, end-user and import questions for defence programmes stay with your compliance team; qualification stays with you.
The short version
- EDGE and ICAPE signed an MoU in Abu Dhabi on 5 May 2026 on local PCB and electronics supply (The Arabian Post, 5 May 2026).
- Walsin lists 83 soft termination MLCC at 100 nF, 14 of them AEC-Q200 in the ST series.
- At 100 nF the rating runs from 25 V in 0402 to 1,500 V in 2225.
- 29 Walsin soft termination lines are on our shelf in Hong Kong (snapshot 9 Nov 2026), including SH18B104K500.
Send us the capacitors on your most flex-exposed board and we will return the Walsin soft termination crosses, field by field. Which parts sit nearest your board edges and connectors?
Related reading
- Flex cracking and board bend: why soft termination exists
- Soft termination MLCC: SH, SG, ST and VT
- AEC-Q200 MLCC: MT versus MG series
- Cross-reference tool, BOM upload and ready stock snapshot
Last reviewed: 16 November 2026.
Sources
Fetched 16 November 2026.
- The Arabian Post, EDGE deepens electronics supply push, 5 May 2026: https://thearabianpost.com/edge-deepens-electronics-supply-push/
- Venatech MLCC upload files Venatech_MLCC_Upload_01.xlsx to _08.xlsx, and Walsin’s SH, SG and ST datasheets, re-measured 16 November 2026; Venatech ready stock snapshot dated 9 November 2026.
Frequently asked questions
What is a soft termination MLCC?
An MLCC with a flexible polymer layer between the ceramic body and the outer plating, so board flex or vibration cracks the termination layer rather than the ceramic. Walsin builds it as SH (silver-polymer), SG (copper-polymer) and ST (AEC-Q200).
How many 100 nF soft termination MLCC does Walsin make?
83 in our count of 16 November 2026: 64 SH, 5 SG and 14 ST, from 0402 to 2225, mostly X7R, rated from 10 V up to 1,500 V.
Which Walsin part crosses a 100 nF, 50 V, 0603 X7R soft termination capacitor?
SH18B104K500, SG18B104K500 or the AEC-Q200 ST18B104K500, all 10 percent. Check thickness, footprint and DC bias against both datasheets.
Does Venatech have soft termination MLCC in stock in the UAE?
We hold stock in Hong Kong, not in the UAE. 29 Walsin SH lines are on our shelf in Hong Kong (snapshot 9 Nov 2026), including SH18B104K500; other lines are quoted through our authorised Walsin channel.
Is a soft termination MLCC suitable for defence electronics in Abu Dhabi?
It addresses flex and vibration cracking, which rugged boards care about, but suitability depends on your qualification. Confirm bend-test data in Walsin’s datasheet, test it in your board, and check export rules with your compliance team.
Can Venatech supply electronics makers in the UAE?
Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to the UAE. Use the cross-reference tool or upload a BOM, and request a quote through the site.