NEWS

Low Voltage Varistor for Agricultural Machinery in Rosario, Argentina: 46 Walsin MOVs from 18 V to 100 V

A low voltage varistor clamps the spikes that relays, solenoids, alternators and long harnesses put onto a 12 V or 24 V machine supply. Walsin lists 46 metal oxide varistors from 18 V to 100 V in five disc sizes, rated 100 A to 6,500 A peak. Venatech is the authorised Walsin distributor in Hong Kong, serving Rosario, Argentina.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for engineers and buyers at the agricultural machinery, implement and farm-electronics makers in Rosario and across Santa Fe province. Walsin Technology (Walsin) is the line we are authorised for. On 16 November 2026 we filtered our varistor upload file, Venatech_MOV_Upload_01.xlsx (379 distinct part numbers), to varistor voltages of 100 V and below and checked the result against our ready stock snapshot dated 9 November 2026. Each count here is ours and each part number is in Walsin’s export.

How is Argentina’s agricultural machinery market moving in 2026?

Up in revenue, mixed by machine. El Litoral reported on 29 May 2026 that INDEC’s first-quarter figures put agricultural machinery billing at about 541,546 million pesos, up 5.7 percent on a year earlier, with seeder billing up 30.9 percent and implements up 8.6 percent in units to 1,910, while tractor units fell 31.2 percent to 937.

By unit, 254 seeders were sold, up 4.5 percent, and 229 combines, down 13.3 percent. Domestic implement units rose 13.8 percent while imported ones fell 21.4 percent, so the local implement makers took share. Santa Fe is where much of that industry shows itself: the provincial government reported on 7 June 2026 that more than 700 Santa Fe firms took part in Agroactiva 2026, held in Armstrong, with more than 280,000 visitors, and that foreign buyers asked for agricultural machinery, agricultural parts and technology among 45 Santa Fe products. Those are INDEC’s and the province’s figures, not ours. Seeders, sprayers and implements now carry monitors, section controllers and rate controllers, all running from the tractor’s low-voltage supply.

Where does a low voltage varistor sit on a 12 V or 24 V machine?

Across the supply input and across inductive loads. On a machine supply, a metal oxide varistor sits from the input line to ground behind the connector, or across a relay coil, solenoid or motor, where it absorbs the energy of switching spikes and conducted surges that would otherwise reach the regulator and the microcontroller.

A varistor’s resistance falls sharply above its varistor voltage, the voltage at 1 mA, so it conducts only during the spike. Choosing one is a balance: the continuous rating must stay above the highest steady supply, including alternator charging and any jump-start condition, while the clamping voltage must stay below what the protected circuit survives. Large events such as an alternator load dump carry far more energy than a small disc absorbs, so they are usually handled by a dedicated suppressor and the system design, with the MOV handling the smaller, repeated spikes. See how to choose an MOV varistor and MOV energy ratings.

How many low voltage varistors does Walsin list?

  1. We counted 46 Walsin varistors at 100 V or below, all in the Standard D series, across ten voltage rungs from 18 V to 100 V and five disc sizes from 5 mm to 20 mm; the 20 mm disc starts at 39 V.
Disc size Parts at 18 V to 100 V Rungs Peak current, 18 V to 68 V Peak current, 82 V and 100 V
5 mm 10 18 V to 100 V 100 A 400 A
7 mm 10 18 V to 100 V 250 A 1,200 A
10 mm 10 18 V to 100 V 500 A 2,500 A
14 mm 10 18 V to 100 V 1,000 A 4,500 A
20 mm 6 39 V to 100 V 2,000 A (39 V to 68 V) 6,500 A

The ten rungs are 18, 22, 27, 33, 39, 47, 56, 68, 82 and 100 V, and Walsin’s export pairs each with a maximum AC working voltage, from 11 Vac at 18 V to 60 Vac at 100 V; the DC continuous rating for each rung is in Walsin’s own MOV catalogue datasheet, MOV_catalog.pdf. The peak current steps up sharply at 82 V on every disc size. The other 333 Walsin varistors start at 205 V and serve mains and industrial supplies. The varistor range page shows the full ladder, and MOV varistor series selection compares the D, E, V and Industrial families.

Which Walsin MOVs answer a 39 V varistor brief for a 24 V machine?

Five, one per disc size. For a 39 V varistor voltage, the rung Walsin pairs with a 25 Vac maximum working voltage, we found five Walsin D series parts, from SR390K05D at 5 mm and 100 A to SR390K20D at 20 mm and 2,000 A, all at 10 percent.

Brief: 39 V varistor voltage, 10 percent, radial disc Walsin part Disc Peak current Match / mismatch Your incumbent
Smallest body SR390K05D 5 mm 100 A Match; check surge life
Small body SR390K07D 7 mm 250 A Match
Mid size SR390K10D 10 mm 500 A Match
Harness input SR390K14D 14 mm 1,000 A Match
Highest current SR390K20D 20 mm 2,000 A Match; 20 mm footprint
One rung up SR470K14D 14 mm 1,000 A Mismatch: 47 V, higher clamp, more DC margin
One rung down SR330K14D 14 mm 1,000 A Mismatch: 33 V, too close to a charging 24 V bus

Leave the last column for your current part. Whether 39 V or 47 V is right for a 24 V machine depends on the DC continuous rating in Walsin’s datasheet for each rung and on your highest steady bus voltage, so read both before you choose. For a 12 V machine the same logic points to the 22 V and 27 V rungs. Disc size sets the surge current and the number of surges the part survives, not the clamping level; the surge-life curves in the same datasheet show how fast that number falls as the pulse grows.

Are Walsin varistors on the Hong Kong shelf?

Not on this snapshot. We checked all 379 Walsin varistors, including the 46 low voltage parts, against our snapshot of 9 November 2026: none is on it, so every Walsin MOV in this post is a line to order through our authorised Walsin channel.

Request a quote with the part numbers and quantities, and ask for the datasheet with it, and we confirm availability, date code and lead time on each quote. If your controller BOM also carries capacitors and resistors, send it whole: the ready stock list is a dated snapshot held in Hong Kong with 1,174 catalogue codes, mostly MLCC and chip resistors, and we will mark which lines are already on our shelf. We give no stock or lead-time promise.

How Venatech helps: what can we cross for a Rosario machinery team?

The protection parts and the rest of the controller. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch at /cross-reference/ decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, and we serve Argentina from Hong Kong in small lots.

Paste the varistor, capacitor and resistor lines into the cross-reference tool, or upload the BOM at /bom/ and request a quote through the site. Every difference from your original is stated, rung by rung and size by size. Transient testing of the finished machine stays with you.

The short version

  • INDEC’s first-quarter 2026 data put agricultural machinery billing up 5.7 percent, seeders up 30.9 percent in billing and tractor units down 31.2 percent (El Litoral, 29 May 2026).
  • More than 700 Santa Fe firms exhibited at Agroactiva 2026 in Armstrong, with more than 280,000 visitors (Government of Santa Fe, 7 June 2026).
  • Walsin lists 46 low voltage varistors, 18 V to 100 V, in five disc sizes.
  • A 39 V brief for a 24 V machine returns five Walsin parts, 100 A to 2,000 A.
  • No Walsin varistor is on our shelf in Hong Kong (snapshot 9 Nov 2026); all are sourced on request.

We will not tell you a part is a drop-in match. We will show you where it differs. On your Santa Fe implement controllers, is it 39 V or 47 V, and why?

Related reading

Last reviewed: 16 November 2026.

Sources

Fetched 16 November 2026.

  • El Litoral, INDEC agricultural machinery first quarter 2026, 29 May 2026: https://www.ellitoral.com/economia/indec-maquinaria-agropecuarias-tractores-implementos-cosechadoras-sembradoras_0_j3OUMEOm8l.html
  • Government of Santa Fe, Agroactiva 2026 news, 7 June 2026: https://www.santafe.gob.ar/noticias/noticia/286251/
  • La Capital, Agroactiva in Armstrong, 7 June 2026: https://www.lacapital.com.ar/agroactiva-condenso-el-pulso-productivo-la-region-la-innovacion-y-el-arraigo-territorial-n10263079.html
  • Venatech varistor upload file Venatech_MOV_Upload_01.xlsx and ready stock snapshot dated 9 November 2026, re-measured 16 November 2026.

Frequently asked questions

What is a low voltage varistor?

A metal oxide varistor with a varistor voltage low enough for 12 V, 24 V or 48 V supplies. Walsin’s low voltage parts run from 18 V to 100 V in the Standard D series.

How many low voltage varistors does Walsin make?

46 at 100 V or below in our count of 16 November 2026, in ten voltage rungs and five disc sizes from 5 mm to 20 mm, out of 379 Walsin varistors in all.

Which Walsin varistor suits a 24 V agricultural machine?

The 39 V rung, SR390K05D to SR390K20D, or the 47 V rung for more margin. Choose from the DC continuous rating in Walsin’s datasheet and your highest bus voltage.

Does a bigger varistor disc clamp lower?

No. Disc size sets peak current and surge life: at 39 V, Walsin’s parts rise from 100 A at 5 mm to 2,000 A at 20 mm. Clamping level follows the voltage rung.

Does Venatech stock varistors in Hong Kong?

No Walsin varistor is on our snapshot of 9 November 2026. They are sourced on request through our authorised Walsin channel, with date code and lead time confirmed on each quote.

Can Venatech supply agricultural machinery makers in Rosario, Argentina?

Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Argentina. Use the free cross-reference tool or upload a BOM; confirm import rules with your compliance team.


Share This, Choose Your Platform!