NEWS

High Temperature MLCC for Solar Plant Electronics in Saudi Arabia: SPPC Round 8 Seeks 3,200 MW, and Walsin Lists 128 HT Parts Rated to 150 °C

For a high temperature MLCC in solar plant electronics for Saudi Arabia, Walsin Technology (Walsin) lists 128 HT series part numbers rated to 150 °C, 102 in X8G and 26 in X8R, and two are on our Hong Kong shelf. Venatech, Walsin’s authorised distributor in Hong Kong, crosses and quotes them.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for a hardware or reliability engineer whose inverters, tracker controllers or monitoring boards go into Saudi solar plants. We parsed Walsin’s MLCC export 00_ALL_MLCC_parts_combined.xlsx (23,601 distinct part numbers) and our stock snapshot as at 9 November 2026. The news was fetched on 17 November 2026, and each figure names its source.

What did SPPC launch in Round 8 of Saudi Arabia’s renewable programme?

A qualification round for 3,200 MW. SaudiGulf Projects reported on 11 November 2026 that the Saudi Power Procurement Company (SPPC) released the request for qualification for Round 8 of the National Renewable Energy Program: three projects totalling 3,200 MW, two solar PV plants of 900 MW and 1,000 MW and a 1,300 MW wind farm.

The solar plants are Tumair in Riyadh province and East Al-Amoah in Aseer province; the wind farm is Al-Mozeraah in Makkah province. Each developer signs a 25-year power purchase agreement with SPPC. The same report says Saudi Energy counted about 19.3 GW of renewables connected to the grid by the end of September 2026, and that the programme aims for renewables and storage to reach about half of installed capacity by 2030. For engineers, 1,900 MW of new PV means thousands of string or central inverter channels and tracker rows, each with control electronics that live outdoors for decades.

Where does a high temperature MLCC earn its place in solar plant electronics?

Where the board runs hotter than 125 °C. A high temperature MLCC rated to 150 °C earns its place on gate-drive and sensing boards mounted close to power modules and heatsinks, in sealed tracker controllers and combiner boxes that sit in full sun, and anywhere a reliability engineer wants margin above X7R’s 125 °C ceiling.

X7R and standard NP0 parts are specified to 125 °C. That is enough for most boards, but the capacitor’s own temperature is what counts, not the air temperature, and a small part on a gate-drive board a few millimetres from an IGBT or SiC module can sit far above ambient. Tracker controllers add another load: a sealed enclosure in direct sun, with no forced air, through a life of 25 years or more. Moving the hottest positions to a 150 °C dielectric is one way to buy margin without redesigning the enclosure. Our note on high temperature MLCC to 150 °C and the HT series covers the series itself, and the solar inverter temperature gate works through the same question for another market.

How many high temperature MLCC does Walsin list?

128 in the HT series, and 235 at 150 °C overall. We counted 128 distinct part numbers in Walsin’s High Temperature (HT) series: 102 in X8G, a class I dielectric to 150 °C, and 26 in X8R, a class II dielectric to 150 °C. Adding X8G parts from the RF and MT series gives 235 Walsin MLCC in a 150 °C class.

Walsin HT series, measured 17 Nov 2026 X8G X8R Total
0402 7 0 7
0603 23 8 31
0805 28 9 37
1206 24 9 33
1210 20 0 20
Total 102 26 128
Rated 50 V 35 26 61
Rated 100 V 67 0 67

The X8G parts run from 1 pF to 15 nF, and the X8R parts from 100 pF to 100 nF, all at 50 V. We have not seen the HT series split by size and voltage this way elsewhere. The full MLCC range lists every family, and NP0 versus X7R versus X5R explains how the dielectric letters work.

Which Walsin parts cross a 4.7 nF, 0805, 150 °C brief?

Three HT parts match, and one is on the shelf. We filtered the export to 4.7 nF in 0805 and checked each row against a gate-drive filter brief: 4.7 nF, 0805, 50 V or more, rated to 150 °C. Three HT rows match; the 125 °C rows that often sit in the same position do not.

Walsin part Series Dielectric Rated voltage Tolerance Max. temperature Match / mismatch with a 4.7 nF, 0805, 50 V, 150 °C brief Your incumbent
HT21G472K500 HT X8G 50 V 10% 150 °C Match, on our shelf in Hong Kong (snapshot 9 Nov 2026)
HT21G472J101 HT X8G 100 V 5% 150 °C Match, tighter tolerance, more voltage
HT21R472K500 HT X8R 50 V 10% 150 °C Match, class II, so check capacitance change with temperature
MT21B472K500 MT, AEC-Q200 X7R 50 V 10% 125 °C Mismatch: 125 °C
0805B472K500 General purpose X7R 50 V 10% 125 °C Mismatch: 125 °C; on our shelf in Hong Kong
0805N472J251 General purpose NP0 250 V 5% 125 °C Mismatch: 125 °C; on our shelf in Hong Kong

HT21G472K500 is the easy pick: X8G is a class I dielectric, so its capacitance barely moves with temperature or DC bias, which is what a timing or filter position wants. Confirm against both datasheets and qualify in your own circuit.

What should a Saudi design team check before moving from X7R to a 150 °C MLCC?

Capacitance reach, dielectric class and the rest of the board. Check that the value you need exists in the HT range, since it tops out at 100 nF, check whether X8G or X8R suits the circuit, and check that the resistors, solder and connectors around the capacitor are rated for the same temperature.

The HT series is a filter and timing family, not a bulk decoupling one: only X8R reaches 100 nF, so a 1 µF bypass part near a hot module still needs a different answer, such as a larger case, a lower-temperature location or a thermal redesign. Between the two dielectrics, X8G behaves like NP0 and suits timing, snubber and RF positions; X8R is class II, so it holds more capacitance per case but changes value with temperature and bias. And a 150 °C capacitor on a board whose solder joints or plastic connectors are rated lower has not raised the board’s limit. Validate thermally with a thermocouple on the part, not on the enclosure wall.

Which 150 °C MLCC are on the Hong Kong shelf?

Two HT lines, both in 0805. Our stock snapshot as at 9 November 2026 holds two Walsin HT series part numbers: HT21G331K500 at 330 pF and HT21G472K500 at 4.7 nF, both 0805, X8G, 50 V.

They are on our shelf in Hong Kong (snapshot 9 Nov 2026) and suit qualification samples and pilot builds. The other 126 HT parts are to order: request a quote and we source them through our authorised Walsin channel. The ready-stock list is a dated snapshot, never live-synced, and we make no stock, price or lead-time promise; we confirm availability, date code and lead time on each quote.

How Venatech helps

How Venatech helps a solar electronics team serving Saudi Arabia is a high temperature MLCC cross with the temperature class stated. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin; each cross states where the Walsin part differs from your original.

Paste your capacitor codes into the cross-reference tool, or upload the whole BOM and request a quote through the site. Check the ready-stock snapshot, dated 9 November 2026. We serve teams in Saudi Arabia from Hong Kong, in small lots with fast quotes. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply. We give no customs or local-content advice; confirm that with your own team.

The short version

SaudiGulf Projects reported on 11 November 2026 that SPPC opened qualification for Round 8, 3,200 MW across two solar plants and a wind farm, in addition to about 19.3 GW of renewables already connected. The electronics in those plants run hot for decades. Walsin lists 128 high temperature MLCC in its HT series, rated to 150 °C, and a 4.7 nF, 0805 brief returns three, one of them on our Hong Kong shelf.

Send us the capacitor lines from your hottest boards, and we will return Walsin crosses with temperature class and every difference stated. Which position on your gate driver runs closest to the module?

Related reading

Last reviewed: 17 November 2026

Sources

Fetched 17 November 2026.

  • SaudiGulf Projects, report on SPPC’s Round 8 request for qualification, 11 November 2026: https://www.saudigulfprojects.com/2026/11/sppc-round-8-solar-wind-projects-rfq-3200-mw-tumair-amoah-mozeraah/
  • Walsin MLCC export, 00_ALL_MLCC_parts_combined.xlsx, re-measured 17 November 2026; Venatech stock snapshot as at 9 November 2026.

Frequently asked questions

What is SPPC Round 8 in Saudi Arabia?

SaudiGulf Projects reported on 11 November 2026 that SPPC released the qualification request for Round 8 of the National Renewable Energy Program: Tumair solar at 900 MW, East Al-Amoah solar at 1,000 MW and Al-Mozeraah wind at 1,300 MW, 3,200 MW in all.

When do solar electronics need a high temperature MLCC?

When the capacitor itself can run above 125 °C, the limit for X7R and standard NP0. Typical cases are gate-drive boards near power modules and sealed tracker controllers in full sun. Measure the part temperature, not the air.

How many 150 °C MLCC does Walsin offer for projects in Saudi Arabia?

We counted 128 parts in Walsin’s HT series, 102 in X8G and 26 in X8R, from 0402 to 1210 at 50 V and 100 V, and 235 Walsin MLCC in a 150 °C class overall. Venatech crosses and quotes them from Hong Kong.

Which Walsin part crosses a 4.7 nF 0805 capacitor rated to 150 °C?

HT21G472K500, an X8G part at 50 V, is the closest match and is on our shelf in Hong Kong (snapshot 9 Nov 2026). HT21G472J101 adds 100 V and 5 percent tolerance. Confirm against both datasheets before release.

What is the difference between X8G and X8R?

Both are rated to 150 °C. X8G is class I, so its capacitance barely changes with temperature or bias; X8R is class II, holds more capacitance per case and changes more. In the HT series, X8G reaches 15 nF and X8R 100 nF.

Is Venatech an authorised Walsin distributor?

Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong and serves teams in Saudi Arabia in small lots. Stackpole and Viking are lines we supply, not authorised lines.


Share This, Choose Your Platform!