NEWS

Thin Film Resistor for Industrial Robot Electronics in China: Robot Output Up 18.9 Percent in September and 1,985 Walsin 0402 Parts at 10 ppm or Tighter

For a thin film resistor in industrial robot electronics in China, Walsin Technology (Walsin) lists 58,314 WF thin film precision resistors in eight sizes, and 1,985 of the 0402 parts carry a TCR of ±10 ppm/°C or tighter. Venatech, Walsin’s authorised distributor in Hong Kong, crosses your resistor and quotes the Walsin line.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for analog and motion-control engineers in China designing servo drives, joint modules, encoders, torque sensors and robot controllers. We parsed Walsin’s eight WF thin film exports, Thin_Film_Precision_Chip_Resistor_WF_Series_0201_060.xlsx through Thin_Film_Precision_Chip_Resistor_WF_Series_2512_643.xlsx, and counted distinct part numbers by size and TCR. The production figures name their source and date.

What did China’s September 2026 industrial data show for robots?

Strong growth. China’s National Bureau of Statistics reported on 20 October 2026 that industrial robot output reached 96,752 sets in September 2026, up 18.9 percent year on year, while integrated circuit output rose 18.4 percent and value added of large industrial firms rose 5.5 percent.

The same release puts September output of new energy vehicles at 1.870 million, up 16.9 percent. It counts finished robots, not drives or controllers, so we add no estimate of the electronics inside them. The direction is still useful for an engineer in Shenzhen or Suzhou: more robots are leaving Chinese lines each month, and every joint of every arm carries a drive, a position sensor and a measurement chain whose accuracy rests on a few precision resistors.

Where does a thin film resistor sit in an industrial robot?

Wherever a ratio must hold its value as the board warms. A robot joint typically uses thin film resistors to set the gain of its current-sense amplifiers, to divide reference voltages for its ADCs and to complete torque and strain bridges; these jobs need TCR of ±25 ppm/°C or tighter.

A thick film resistor drifts too far for this work: typical general-purpose thick film parts carry ±100 to ±200 ppm/°C, which shifts a gain by a percent or more across a hot drive. Thin film parts are sputtered, laser-trimmed metal films that hold their value far more tightly and with lower noise. In a joint module the drive and motor sit centimetres apart, so the electronics see tens of degrees of swing between idle and full torque. Our guide to thin film vs thick film chip resistors sets out the difference, and the thin film range lists every Walsin part.

How many thin film precision resistors does Walsin list, and at what TCR?

Fifty-eight thousand three hundred and fourteen. We counted 58,314 distinct WF part numbers across eight sizes from 0201 to 2512; 6,678 are rated ±10 ppm/°C, 6,007 are rated ±5 ppm/°C and 3,064 are rated ±3 ppm/°C.

Size ±3 ppm ±5 ppm ±10 ppm ±15 ppm ±25 ppm ±50 ppm Total
0201 0 0 0 0 3,164 2,342 5,506
0402 595 616 774 774 1,800 1,800 6,359
0603 769 789 887 887 2,114 2,116 7,562
0805 832 853 974 974 2,176 2,176 7,985
1206 868 887 994 994 2,338 2,346 8,427
1210 0 887 979 979 2,177 2,194 7,216
2010 0 964 1,026 1,026 2,210 2,210 7,436
2512 0 1,011 1,044 1,044 2,362 2,362 7,823
Total 3,064 6,007 6,678 6,678 18,341 17,546 58,314

For 0402, the size most joint drives use for analog work, 595 + 616 + 774 = 1,985 parts sit at ±10 ppm/°C or tighter. Measured by value, the ±3 ppm 0402 parts run from 10 ohm to 7.96 kilohm, the ±5 ppm parts reach 10 kilohm, and the ±10 ppm parts reach 59.7 kilohm. Every 0402 WF row in our export lists ±0.01 percent tolerance.

Which Walsin thin film resistor fits a 10 kilohm, 0402, 10 ppm brief?

Two parts meet it. For a brief of 10 kilohm, 0402, TCR ±10 ppm/°C or tighter, WF04Z1002TTL matches at ±5 ppm/°C and WF04W1002TTL matches at ±10 ppm/°C; both are rated 1/10 W.

Put your incumbent resistor in the last column and compare each field.

Walsin part Resistance Tolerance (export) TCR (ppm/°C) Rated power Match / mismatch with 10 kilohm, 0402, ±10 ppm or tighter Your incumbent
WF04Z1002TTL 10 kilohm ±0.01% ±5 1/10 W Match, twice the margin on TCR
WF04W1002TTL 10 kilohm ±0.01% ±10 1/10 W Match
WF04F1002TTL 10 kilohm ±0.01% ±15 1/10 W Mismatch: TCR
WF04R1002TTL 10 kilohm ±0.01% ±25 1/10 W Mismatch: TCR
WF04U1002TTL 10 kilohm ±0.01% ±25 1/16 W Mismatch: TCR and power
WF04Q1002TTL 10 kilohm ±0.01% ±50 1/10 W Mismatch: TCR
WF04Z4991TTL 4.99 kilohm ±0.01% ±5 1/10 W Mismatch on value; fits a 4.99 kilohm divider
WF04B4991TTL 4.99 kilohm ±0.01% ±3 1/10 W Mismatch on value; fits a ±3 ppm 4.99 kilohm brief

The fifth character of each code carries the TCR family: B, Z, W, F, R, U and Q in the rows above. That makes a mixed-TCR BOM easy to audit by eye. Check the datasheet for the tolerance codes available in each family and for long-term stability under load before release.

How much gain drift does resistor TCR add in a robot joint?

Up to TCR times temperature swing. Two ±10 ppm/°C resistors setting an amplifier gain can drift in opposite directions; across a 50 °C swing the worst case is 2 × 10 × 50 = 1,000 ppm, or 0.1 percent of gain.

That is the case where the two parts move in opposite directions. In practice parts from the same family often drift together, and the ratio holds better than the worst case, but a design should not rely on it unless the datasheet or a matched network says so. At ±5 ppm/°C the same worst case is 0.05 percent, and with ±25 ppm/°C parts it reaches 0.25 percent, which is visible in the torque loop of a precise arm. Our piece on what resistor TCR actually buys you works through the arithmetic for other circuits.

Can Venatech supply Walsin thin film resistors to China from Hong Kong?

Yes, to order. All 58,314 Walsin WF thin film resistors, including the 1,985 0402 parts at ±10 ppm/°C or tighter, can be quoted from Hong Kong: none is on our shelf in the snapshot dated 9 November 2026, so request a quote and we source them through our authorised Walsin channel.

Each quote states availability, date code and lead time for the line, and we work in small lots for engineering builds and pilot runs. We make no stock, price or lead-time promise. The ready-stock list, a dated snapshot, covers MLCC and chip resistors that sit on the same drive and controller boards.

Have part numbers to quote? upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.

How Venatech helps: what should a Chinese robot team send us?

The precision resistors from your drive and sensor BOMs. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.

Paste a resistor code into the cross-reference tool, or upload the whole BOM and request a quote through the site. The ready-stock snapshot is dated 9 November 2026. We serve Shenzhen, Dongguan, Suzhou, Shanghai and Foshan from Hong Kong, a short trip from the Pearl River Delta, with fast quotes and small lots. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.

The short version

China’s industrial robot output reached 96,752 sets in September 2026, up 18.9 percent, the National Bureau of Statistics reported on 20 October 2026. Every robot joint relies on precision resistors for gain, references and bridges. Walsin covers that job with 58,314 WF thin film resistors, 1,985 of them 0402 parts at ±10 ppm/°C or tighter, and WF04Z1002TTL meets a 10 kilohm, 0402, 10 ppm brief at ±5 ppm/°C.

Send us the precision resistors in your drive and we will return Walsin crosses with every difference stated. What temperature swing does your joint electronics see?

Related reading

Last reviewed: 18 November 2026.

Sources

Fetched 18 November 2026.

  • National Bureau of Statistics of China, Industrial Production Operation in September 2026, 20 October 2026: https://www.stats.gov.cn/english/PressRelease/202610/t20261020_1965665.html
  • Walsin thin film exports Thin_Film_Precision_Chip_Resistor_WF_Series_0201_060.xlsx, _0402_100.xlsx, _0603_160.xlsx, _0805_201.xlsx, _1206_321.xlsx, _1210_322.xlsx, _2010_502.xlsx and _2512_643.xlsx, re-measured 18 November 2026; Walsin WF datasheet on Walsin’s own site for tolerance codes and stability; Venatech Hong Kong stock snapshot dated 9 November 2026.

Frequently asked questions

What did China’s September 2026 data show for industrial robots?

The National Bureau of Statistics reported on 20 October 2026 that industrial robot output reached 96,752 sets in September 2026, up 18.9 percent year on year.

What TCR does a thin film resistor need in a robot servo drive in China?

Gain-setting and reference resistors in a joint drive usually need ±25 ppm/°C or tighter, and ±10 or ±5 ppm/°C where the loop must hold calibration across a wide temperature swing.

How many thin film precision resistors does Walsin list?

We counted 58,314 WF parts in eight sizes. In 0402, 1,985 carry ±10 ppm/°C or tighter: 595 at ±3, 616 at ±5 and 774 at ±10.

Which Walsin thin film resistor crosses a 10 kilohm 0402 part at 10 ppm?

WF04Z1002TTL at ±5 ppm/°C and WF04W1002TTL at ±10 ppm/°C, both 1/10 W. WF04F1002TTL and WF04R1002TTL miss on TCR.

Is a thin film resistor better than thick film for a current-sense amplifier gain?

Usually, yes. Thin film parts hold TCR of ±5 to ±50 ppm/°C, while general-purpose thick film parts typically sit at ±100 to ±200 ppm/°C, so gain drifts far less with temperature.

Can Venatech supply Walsin thin film resistors to China from Hong Kong?

Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong. Request a quote and we source the parts through our authorised Walsin channel, with availability, date code and lead time stated on each quote.


Share This, Choose Your Platform!