Elbit Systems reported a 33 billion US dollar order backlog on 17 November 2026 and said it is expanding production capacity. For the radios and RF boards behind that work, Walsin Technology (Walsin) lists 1,360 wirewound chip inductors, 27 of them at 10 nH. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for RF and hardware engineers, and the buyers who support them, at defence, security and communications electronics makers and EMS suppliers in Israel. A results release is a business fact, not a forecast, and we make no claim about any company’s suppliers or bill of materials. What a growing defence order book does mean is more radio, datalink and sensor boards to build and second-source, and every one of them carries small RF inductors in its matching and filter networks. On 18 November 2026 we re-measured Walsin’s inductor export (Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx, 5,410 part numbers) for the WLCW and WQCW wirewound families.
What did Elbit Systems report on 17 November 2026?
A record order book. Elbit Systems’ third-quarter 2026 release, published on StockTitan on 17 November 2026, reports revenue of about 2.25 billion US dollars for the quarter, up about 17 percent year on year, and an order backlog of 33.0 billion US dollars at 30 September 2026.
The same release says about 74 percent of that backlog comes from customers outside Israel and about 35 percent is scheduled for the rest of 2026 and 2027. Its chief executive is quoted as saying, “We are expanding production capacity while increasingly harnessing AI across our operations.” The release does not name the sites where capacity will be added, and we do not guess. By region, Europe accounted for about 557 million US dollars of the quarter’s revenue and North America for about 456 million. None of this tells you anything about passive-component supply, and we do not suggest it does.
Why does a defence backlog in Israel matter to an RF chip inductor buyer?
Because RF boards are inductor-heavy. A single radio or datalink front end can use dozens of chip inductors between 1 nH and 100 nH for impedance matching, filters and bias feeds, and Walsin’s two wirewound families cover that range in six case sizes from 0402 to 1812.
When a programme moves from prototype to rate production, the bill of materials gets a harder look. Buyers ask for a second source on every line that has only one, and engineers ask whether the second source holds the same Q and self-resonant frequency, not only the same nominal inductance. That is where a wirewound part and a multilayer part differ: a wirewound chip inductor usually gives higher Q at the same value. Our guide to multilayer vs wirewound chip inductors explains the trade-off, and the note on WLCW vs WQCW sets out how Walsin’s two wirewound ranges line up.
How many Walsin wirewound inductors sit at 10 nH?
Twenty-seven. We parsed all 5,410 inductor rows in Walsin’s export and counted 1,360 distinct WLCW and WQCW wirewound part numbers: 791 WLCW and 569 WQCW. Of those, 27 are rated at 10 nH, across five case sizes from 0402 to 1210.
We also counted 717 of the 1,360 with a minimum Q of 40 or more, and 153 WLCW part numbers in the high-Q HQ build, all in 0603, 0805 and 1008. The table shows one tolerance per row for the 10 nH parts; the ±2 %, ±5 % and ±10 % versions share the same Q, resistance and current in the export.
| Walsin part | Case | Tolerance | Q min | SRF min (export) | DC resistance | Rated current |
|---|---|---|---|---|---|---|
WLCW1005Z0G10NTB |
0402 | ±2 % | 21 | 3.9 GHz | 0.2 Ω | 480 mA |
WQCW1005Z0J10NTB |
0402 | ±5 % | 21 | 3.9 GHz | 0.2 Ω | 480 mA |
WLCW1608Z0G10NPB |
0603 | ±2 % | 31 | 4.8 GHz | 0.13 Ω | 700 mA |
WLCW1608HQG10NPB |
0603 | ±2 % | 49 | 4.3 GHz | 0.048 Ω | 1.4 A |
WLCW2012Z0G10NPB |
0805 | ±2 % | 60 | 4.2 GHz | 0.1 Ω | 600 mA |
WLCW2520HQG10NPB |
1008 | ±2 % | 60 | 3.6 GHz | 0.06 Ω | 1.6 A |
Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.
Check the datasheet for the test frequency behind each Q figure and for the SRF unit; the export states some SRF values in GHz and some in MHz, and we have converted them here. Our note on inductor self-resonant frequency explains why SRF should sit well above your operating band.
Which RF chip inductor fits a 1 GHz to 2 GHz matching network?
Usually the 0603 high-Q part. For a 10 nH, ±2 % position in a 1 GHz to 2 GHz match, the 0603 HQ build gives Q 49 against Q 31 for the standard 0603 and Q 21 for 0402, with an SRF of 4.3 GHz, about twice the upper edge of the band.
This is a worked example, not a design rule. Your incumbent part, board layout and test frequency decide the real answer. The fit column below assumes a 10 nH ±2 % brief, Q of 40 or more, SRF at least twice 2 GHz, and an 0603 footprint.
| Walsin part | Case | Q min | SRF | Match / mismatch for the example brief | Your incumbent |
|---|---|---|---|---|---|
WLCW1608HQG10NPB |
0603 | 49 | 4.3 GHz | Match: Q, SRF and footprint all pass | |
WLCW1608Z0G10NPB |
0603 | 31 | 4.8 GHz | Mismatch on Q; match on SRF and footprint | |
WQCW1608Z0G10NPB |
0603 | 31 | 4.8 GHz | Mismatch on Q; match on SRF and footprint | |
WLCW1005Z0G10NTB |
0402 | 21 | 3.9 GHz | Mismatch on Q and footprint; use if board space rules | |
WLCW2012Z0G10NPB |
0805 | 60 | 4.2 GHz | Mismatch on footprint; match on Q and SRF |
Put your incumbent part number in the last column, compare both datasheets, and measure the network on your own board. Q and SRF move with pad layout and nearby ground, so a drop-in match on paper still needs a test on the bench.
Can I get these inductors in Hong Kong?
Yes, to order. We checked all 1,360 WLCW and WQCW part numbers against our ready-stock snapshot dated 9 November 2026; they are supplied to order, so request a quote and we source them through our authorised Walsin channel.
We confirm availability, date code and lead time on each quote rather than in advance, and we make no promise of either. For a programme that needs paperwork, ask for the Walsin datasheet revision and the lot and date code to be stated on the quote, so your incoming inspection can match the parts to the record. If your board also carries capacitors and resistors, the same quote can cover them: our ready-stock snapshot lists the MLCC and chip resistors on our shelf in Hong Kong on 9 November 2026.
How Venatech helps
How Venatech helps is a checked cross before the build. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, so an RF inductor list returns Walsin candidates with Q, SRF and size differences stated.
Paste your inductor part numbers into the cross-reference tool, or upload the whole radio-board BOM and request a quote through the site. We are Hong Kong-based, serve buyers in Israel in small lots, and confirm availability, date code and lead time on every quote. The inductor range page lists the Walsin families. Walsin is our authorised line; Stackpole and Viking are lines we supply. For export-control or defence procurement rules, confirm with your compliance team.
The short version
Elbit Systems reported a 33 billion US dollar backlog on 17 November 2026 and said it is expanding production capacity. Radio and sensor boards need RF chip inductors with the right Q and SRF, not only the right value. Walsin lists 1,360 WLCW and WQCW wirewound inductors, 27 at 10 nH and 717 with Q of 40 or more; for a 1 GHz to 2 GHz match, WLCW1608HQG10NPB gives Q 49 in 0603.
Send us the inductor lines from your current RF board, and we will return Walsin crosses with Q and SRF stated. Which inductor on that board has only one source today?
Related reading
- Multilayer vs wirewound chip inductors
- WLCW vs WQCW: Walsin’s two wirewound families
- Inductor self-resonant frequency
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 18 November 2026
Sources
Fetched 18 November 2026.
- Elbit Systems, third-quarter 2026 results release, via StockTitan, 17 November 2026: https://www.stocktitan.net/news/ESLT/elbit-systems-reports-third-quarter-2026-6v3noo5s9yqp.html
- Walsin inductor export, Venatech_Inductor_Upload_01.xlsx and Venatech_Inductor_Upload_02.xlsx, re-measured 18 November 2026; Venatech ready-stock snapshot dated 9 November 2026.
Frequently asked questions
<!– wp:rank-math/faq-block {"questions":[{"id":"faq-question-01","title":"What is Elbit Systems' order backlog in 2026?","content":"Elbit's third-quarter release of 17 November 2026 reports a backlog of 33.0 billion US dollars at 30 September 2026, about 74 percent from outside Israel. We make no claim about its suppliers.","visible":true},{"id":"faq-question-02","title":"What is the best RF chip inductor for a defence radio in Israel?","content":"There is no single answer. Start from value, tolerance, Q at your frequency, SRF and footprint. In our worked example,WLCW1608HQG10NPB gives Q 49 and a 4.3 GHz SRF at 10 nH in 0603.”,”visible”:true},{“id”:”faq-question-03″,”title”:”How many Walsin wirewound chip inductors are there?”,”content”:”We counted 1,360 distinct WLCW and WQCW part numbers in Walsin’s export: 791 WLCW and 569 WQCW, in six case sizes from 0402 to 1812.”,”visible”:true},{“id”:”faq-question-04″,”title”:”Why does inductor Q factor matter in an RF matching network?”,”content”:”Lower Q means more loss in the network and a broader, weaker response. At 10 nH in 0603, Walsin’s HQ build lists Q 49 against Q 31 for the standard part.”,”visible”:true},{“id”:”faq-question-05″,”title”:”How far above my band should the self-resonant frequency be?”,”content”:”A common rule of thumb is at least twice the highest operating frequency. Check the datasheet curve and measure on your own board.”,”visible”:true},{“id”:”faq-question-06″,”title”:”Is Venatech an authorised Walsin distributor for buyers in Israel?”,”content”:”Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Israel in small lots. Stackpole and Viking are lines we supply, not authorised lines.”,”visible”:true}],”listStyle”:””,”titleWrapper”:”h3″,”titleCssClasses”:””,”contentCssClasses”:””,”sizeSlug”:””} –>
What is Elbit Systems’ order backlog in 2026?
Elbit’s third-quarter release of 17 November 2026 reports a backlog of 33.0 billion US dollars at 30 September 2026, about 74 percent from outside Israel. We make no claim about its suppliers.
What is the best RF chip inductor for a defence radio in Israel?
There is no single answer. Start from value, tolerance, Q at your frequency, SRF and footprint. In our worked example, WLCW1608HQG10NPB gives Q 49 and a 4.3 GHz SRF at 10 nH in 0603.
How many Walsin wirewound chip inductors are there?
We counted 1,360 distinct WLCW and WQCW part numbers in Walsin’s export: 791 WLCW and 569 WQCW, in six case sizes from 0402 to 1812.
Why does inductor Q factor matter in an RF matching network?
Lower Q means more loss in the network and a broader, weaker response. At 10 nH in 0603, Walsin’s HQ build lists Q 49 against Q 31 for the standard part.
How far above my band should the self-resonant frequency be?
A common rule of thumb is at least twice the highest operating frequency. Check the datasheet curve and measure on your own board.
Is Venatech an authorised Walsin distributor for buyers in Israel?
Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Israel in small lots. Stackpole and Viking are lines we supply, not authorised lines.