NEWS

0.1 Percent Precision Resistor for Chip Test Equipment in Japan: 690 of 967 Listed Firms Lift Half-Year Profit and 1,029 Walsin 25 ppm Thick-Film Parts

For a 0.1 percent precision resistor on chip test equipment in Japan, Walsin Technology (Walsin) lists 16,103 thick-film parts at ±0.1%, and 1,029 of them hold ±25 ppm/°C in 0603, 0805 and 1206. Venatech Limited, an authorised Walsin distributor in Hong Kong, crosses your precision parts and quotes them.


This post is for engineers in Japan who design the measurement paths of testers, load boards, probe interfaces and instruments, and for the buyers who source their precision parts. We counted the rows ourselves in Walsin’s chip resistor exports (Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_79.xlsx, 234,378 part numbers) and read the high-precision group against the datasheets named in the export. The business figures carry their source and date.

What did Japanese companies report for April to September 2026?

Mostly higher profits. Jiji Press, as published by The Nation on 15 November 2026, reported that 690 of 967 TOPIX-listed companies with March year-ends posted higher ordinary profit for April to September, citing SMBC Nikko Securities; 369 raised full-year net profit forecasts and 74 cut them.

The same report says Advantest posted record first-half sales, operating profit and net profit, and that its chief executive described the AI chip market as a megacycle. It also notes record April to September operating profit at Panasonic Holdings from energy storage and data-centre components, and records warnings from some materials makers that AI investment could slow. We add no forecast and say nothing about any company’s suppliers. For a test engineer in Japan the signal is that the equipment which measures AI chips is busy, and every tester depends on resistors whose value it can trust over temperature.

Why does chip test equipment need a 0.1 percent precision resistor?

Because the measurement is only as good as its references. A 0.1 percent precision resistor sets gain, current-sense and divider ratios to within 1,000 ppm of nominal, and a ±25 ppm/°C part adds no more than 250 ppm of drift over a 10 °C swing inside a test head.

In test equipment the precision resistor shows up in pin electronics, parametric measurement units, precision current sources, reference dividers and calibration paths. Tolerance sets the starting error, which calibration can remove; TCR sets the error that moves with temperature after calibration, which it cannot. That is why test engineers usually care more about TCR and ratio tracking than about the tolerance code alone. Our guide to what resistor TCR actually buys you works through the arithmetic, and the chip resistor range lists every part.

How many Walsin 0.1 percent precision resistors are there, and at what TCR?

Sixteen thousand one hundred and three. We counted 16,103 Walsin high-precision thick-film parts at ±0.1%; 1,029 hold ±25 ppm/°C, 4,340 hold ±50 ppm/°C and the rest are at ±100 ppm/°C or wider.

Case size ±25 ppm ±50 ppm ±100 ppm Other Total at ±0.1%
0201 (0603) 0 0 0 1,142 1,142
0402 (1005) 0 914 1,712 1 2,627
0603 (1608) 343 1,142 1,712 1 3,198
0805 (2012) 343 1,142 1,712 1 3,198
1206 (3216) 343 1,142 1,712 1 3,198
1210 (3225) 0 0 1,141 1 1,142
2010 and 2512 0 0 1,598 0 1,598
Total 1,029 4,340 9,587 1,147 16,103

The “other” column is mostly the 0201 parts, which the export lists at ±200 ppm/°C. The whole Walsin high-precision thick-film group holds 52,027 part numbers across ±0.1%, ±0.25%, ±0.5% and ±1%, so the 25 ppm, 0.1% slice is a deliberately narrow one. We have not seen it broken out by case and TCR this way elsewhere.

Which Walsin part fits a 10 kilohm, 0.1 percent, 25 ppm brief?

Two parts meet it. For a brief of 10 kilohm, ±0.1%, ±25 ppm/°C or better, 0603 or 0805, WF06J1002BTL and WF08J1002BTL match; the 50 ppm and 100 ppm parts at the same value are mismatches on TCR.

Put your incumbent precision resistor in the last column and compare each field.

Walsin part Value Tolerance TCR (ppm/°C) Case, power Match / mismatch with 10 kilohm, ±0.1%, 25 ppm, 0603 or 0805 Your incumbent
WF06J1002BTL 10 kilohm ±0.1% ±25 0603, 0.1 W Match
WF08J1002BTL 10 kilohm ±0.1% ±25 0805, 0.125 W Match; larger body
WF12J1002BTL 10 kilohm ±0.1% ±25 1206, 0.25 W Mismatch: case larger than 0805
WF06K1002BTL 10 kilohm ±0.1% ±50 0603, 0.1 W Mismatch: TCR
WF06H1002BTL 10 kilohm ±0.1% ±100 0603, 0.1 W Mismatch: TCR
SF06H1002BTL 10 kilohm ±0.1% ±100 0603, 0.1 W Mismatch: TCR; anti-sulfuration build

Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.

The J code in the fifth position marks the TC25 family, K the TC50 family and H the TC100 family, so a quick read of the part number tells you the TCR class before you open the datasheet.

Check the datasheet. Long-term stability, current noise and the TCR test range are on the datasheets named in the export for each family, not in the export itself. Read them before you place a thick-film part in a calibration path.

When is a thick-film 0.1 percent precision resistor not enough?

When drift, not tolerance, sets your error budget. Thick film reaches ±0.1% and ±25 ppm/°C in Walsin’s range; below about 25 ppm/°C, or where current noise and long-term drift matter, thin film is the usual choice.

A tester that calibrates daily can live with a 25 ppm part in most paths, because calibration removes the tolerance and the remaining drift is small over a controlled head temperature. A reference divider, a precision current source or a ratio pair that must hold over weeks without recalibration often moves to thin film, where TCR and stability are tighter and noise is lower. Our comparison of thin film vs thick film chip resistors and the note on precision thin-film tolerance and TCR set out where the line falls. VenaMatch will show you the thick-film and thin-film Walsin candidates side by side.

Can Venatech supply Walsin precision resistors from Hong Kong?

Yes, both from stock and to order. Three ±0.1% precision lines are on our shelf in Hong Kong (snapshot 9 Nov 2026), WF08H8203BTL, WF12H1202BTL and WF12H5762BTL, all at ±100 ppm; the 1,029 parts at 25 ppm are quoted to order through our authorised Walsin channel.

Each quote states availability, date code and lead time for the line, and we work in small lots for engineering builds and board revisions. We make no stock, price or lead-time promise. The ready-stock list shows the full dated snapshot.

How Venatech helps: what should a Japanese test team send us?

The precision parts on your measurement BOM. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.

Paste a resistor code into the cross-reference tool, or upload the whole BOM and request a quote through the site; flag the paths where TCR matters most. The ready-stock snapshot is dated 9 November 2026. We serve Tokyo, Kanagawa, Gunma and Kyushu from Hong Kong, with fast quotes and small lots. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.

The short version

690 of 967 TOPIX-listed companies lifted April to September profit and Advantest posted record first-half results, Jiji Press reported via The Nation on 15 November 2026. Test equipment for AI chips depends on precision resistors that hold their value over temperature. Walsin lists 16,103 thick-film parts at ±0.1%, 1,029 of them at ±25 ppm in 0603, 0805 and 1206, and WF06J1002BTL meets a 10 kilohm, 0.1%, 25 ppm brief in 0603.

Send us the precision resistors in your measurement path and we will return Walsin crosses with every difference stated. Which path in your tester sets your drift budget?

Related reading

Last reviewed: 19 November 2026.

Sources

Fetched 19 November 2026.

  • The Nation (Jiji Press), report on Japanese companies’ April to September 2026 results, 15 November 2026: https://www.nationthailand.com/news/world/40073540
  • Walsin chip resistor exports, Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_79.xlsx, re-measured 19 November 2026; Walsin high-precision thick-film datasheets as named in the export; Venatech Hong Kong stock snapshot dated 9 November 2026.

Frequently asked questions

What did Japanese listed companies report for April to September 2026?

Jiji Press, via The Nation on 15 November 2026, reported that 690 of 967 TOPIX-listed firms with March year-ends posted higher ordinary profit, and that Advantest posted record first-half sales and profit.

Why does semiconductor test equipment use 0.1 percent precision resistors?

They set gain, current-sense and divider ratios in pin electronics, measurement units and reference paths. Tolerance sets the starting error; TCR sets the drift that remains after calibration.

How many Walsin 0.1 percent precision resistors hold 25 ppm?

We counted 1,029 Walsin thick-film parts at ±0.1% and ±25 ppm/°C, 343 each in 0603, 0805 and 1206, out of 16,103 at ±0.1%.

Which Walsin part crosses a 10k 0.1% 25ppm 0603 resistor?

WF06J1002BTL matches in 0603 and WF08J1002BTL in 0805. Read stability and noise on the datasheet before release.

Is thick film good enough for a precision test path in Japan?

Often, where the tester calibrates regularly and the head temperature is controlled. For drift below 25 ppm/°C or long unattended intervals, consider thin film.

Is Venatech an authorised Walsin distributor for buyers in Japan?

Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Japan in small lots. Stackpole and Viking are lines we supply, not authorised lines.


Share This, Choose Your Platform!