Alberta set out new data centre rules on 18 November 2026 that would touch about 30 percent of roughly 60 proposed projects. The ones that go ahead still need surge protection on 347/600 V power: Walsin Technology (Walsin) lists 116 MOV varistors rated 385 VAC or more. Venatech is the authorised Walsin distributor in Hong Kong.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for engineers and buyers in Canada who design power distribution, UPS and surge-protection equipment for data-centre projects. A provincial siting and water rule is not a component rule, and this is perspective, not legal or permitting advice. What the Alberta news does is sharpen the list of projects likely to proceed, and those projects run on Canadian 600 V three-phase distribution, where the surge stage is set by the 347 V phase-to-neutral voltage. On 19 November 2026 we re-measured Walsin’s varistor export (Venatech_MOV_Upload_01.xlsx, 379 part numbers) against our ready-stock snapshot dated 9 November 2026.
What do Alberta’s new data centre rules say?
Setbacks, water limits and higher fines. The Red Deer Advocate reported on 18 November 2026 that Alberta would bar data centres of 10 MW or more within 600 metres of the nearest home and from the province’s best or irrigated farmland, if the changes pass.
The same report says a province-wide standard would aim to cut cooling water use close to zero, maximum fines for serious environmental contamination would rise to six million Canadian dollars, and Technology and Innovation Minister Nate Glubish said about 30 percent of the roughly 60 proposed data centre projects would be affected. The Logic reported on 18 November 2026 that the rules would give the Alberta Utilities Commission authority to review and approve large data centres, that projects already advanced or past certain regulatory milestones would be grandfathered, and that the rules came a day after the commission approved a 1,494 MW gas-fired plant near Calgary to supply a hyperscale data centre being developed by Beacon Data Centers. Which projects qualify is for each developer and its advisers.
Why does a data centre rule matter to an MOV varistor buyer in Canada?
Because roughly 70 percent of the pipeline is not touched. If about 30 percent of some 60 projects are affected, as the minister said, the rest move on to procurement, and every switchboard, PDU, UPS and power-supply front end in them carries a surge stage built on metal-oxide varistors.
The rule also tilts design, and it changes which datasheet rows matter. Near-zero cooling water points to closed-loop and dry cooling, which adds pumps, fans and their drives, each with its own mains input to protect. We make no forecast about any developer, operator or equipment maker. The engineering question is the same one for every project that proceeds: is the varistor in your surge stage rated for 347 V phase-to-neutral with margin, and does it have the energy rating for its position in the building? Our guide on how to choose an MOV varistor walks through the working-voltage and surge-current steps.
How many Walsin MOV varistors are rated 385 VAC or more?
One hundred and sixteen part numbers. We parsed all 379 rows of Walsin’s varistor export and counted 116 distinct MOVs with a maximum continuous working voltage of 385 VAC or more, from 390 VAC to 750 VAC, across all four series.
| Walsin MOV series | Part numbers at 385 VAC or more | Disc sizes | Peak current range |
|---|---|---|---|
| Standard (D Series) | 36 | 5 mm to 25 mm | 400 A to 18,000 A |
| High Energy (E Series) | 12 | 5 mm, 7 mm, 18 mm | 800 A to 9,000 A |
| Super High Energy (V Series) | 24 | 10 mm to 20 mm | 4,000 A to 13,000 A |
| Industrial | 44 | 32 mm to 53 mm, round and 34 mm square | 30,000 A to 80,000 A |
| Total | 116 |
By working voltage, the 116 split as 17 at 390 VAC, 17 at 420 VAC, 13 each at 460, 485, 510, 550, 625 and 680 VAC, 3 at 575 VAC and 1 at 750 VAC. That gives 34 parts in the 390 VAC to 420 VAC band for 347 V circuits and 27 at 625 VAC or more for line-to-line protection on 600 V. We have not seen this cut counted anywhere else. Peak current here is the export’s peak-current column; the joule rating per part is on Walsin’s datasheet (MOV_catalog.pdf). The full MOV range holds the lower-voltage steps for 120 V and 208 V circuits.
Which MOV varistor fits a 347 V or 600 V surge stage?
Start at 390 VAC or 420 VAC for 347 V to neutral. A common practice is to choose a continuous rating at least 10 to 15 percent above nominal; on 347 V that points to the 390 VAC and 420 VAC parts, and then the disc size follows the surge current at that point in the building.
| Walsin part | Series | Size | Max working voltage | Peak current | Match / mismatch for a 347 V phase-to-neutral stage in a data-centre distribution board | Your incumbent |
|---|---|---|---|---|---|---|
SR681K40D |
Industrial | 40 mm | 420 VAC | 40,000 A | Match for a service-entrance or main-board stage | |
SR681K34RD |
Industrial | 34 mm square | 420 VAC | 80,000 A | Match where the energy budget is highest | |
SR681K20E |
Super High Energy (V) | 20 mm | 420 VAC | 13,000 A | Match for a branch PDU or UPS input | |
SR621K14D |
Standard (D) | 14 mm | 390 VAC | 4,500 A | Match for a power-supply front end, with less margin | |
SR112K32D |
Industrial | 32 mm | 680 VAC | 30,000 A | Match for line-to-line on 600 V | |
SR621K05D |
Standard (D) | 5 mm | 390 VAC | 400 A | Mismatch for a distribution board; board-level only |
Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.
Put your incumbent in the last column and confirm clamping voltage, energy and thermal disconnect against both datasheets; Walsin’s MOV datasheet (MOV_catalog.pdf) carries the energy and clamping columns the export leaves out. Our notes on MOV energy ratings at 40,000 A and 80,000 A and series selection across D, E, V and Industrial cover the next step. Certification of a surge protective device is a question for your certification engineer.
Are Walsin high-voltage MOVs on the shelf in Hong Kong?
They are to order. We checked all 116 Walsin MOVs rated 385 VAC or more against our ready-stock snapshot dated 9 November 2026; they are supplied to order, so request a quote and we source them through our authorised Walsin channel.
Data-centre equipment builds tend to run in project lots, which suits a to-order line: send the part numbers from your surge stages with the project quantity and we confirm availability, date code and lead time on each quote. The same boards often carry Walsin chip resistors and MLCC for control and sensing, and our ready-stock snapshot shows which of those were on our shelf in Hong Kong (snapshot 9 November 2026) for prototype lots.
How Venatech helps
How Venatech helps is a checked cross before the switchboard is released. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, so a list of incumbent varistors returns Walsin candidates with working voltage, disc size and surge current stated.
Paste your varistor part numbers into the cross-reference tool, or upload the whole power-distribution BOM and request a quote through the site. The ready-stock snapshot, dated 9 November 2026, lists what is on our shelf in Hong Kong. We are Hong Kong-based, serve buyers in Alberta, Ontario and Quebec in small lots, and confirm availability, date code and lead time on every quote. Walsin is our authorised line; Stackpole and Viking are lines we supply. For anything about permits or approvals, confirm with your compliance team.
The short version
Alberta’s proposed data centre rules, reported on 18 November 2026, would bar 10 MW-plus sites within 600 metres of homes and from prime farmland and would touch about 30 percent of roughly 60 projects. The projects that proceed still need surge protection on 347/600 V power. Walsin lists 116 MOV varistors rated 385 VAC or more, 34 of them in the 390 VAC to 420 VAC band for 347 V circuits.
Send us the surge-stage parts from your switchboard or UPS and we will return Walsin crosses with voltage and energy stated. Which varistor in your design is sized for 120 V when the building runs at 347 V?
Related reading
- How to choose an MOV varistor
- MOV energy ratings: 40,000 A vs 80,000 A
- MOV varistor series selection: D, E, V and Industrial
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 19 November 2026
Sources
Fetched 19 November 2026.
- Red Deer Advocate, “Province unveils new data centre regulations”, 18 November 2026: https://reddeeradvocate.com/2026/11/18/province-unveils-new-data-centre-regulations/
- The Logic, “Alberta exempts data centres already in the works from its new restrictions”, 18 November 2026: https://thelogic.co/briefing/alberta-exempts-data-centres-already-in-the-works-from-its-new-restrictions/
- Walsin varistor export, Venatech_MOV_Upload_01.xlsx, re-measured 19 November 2026; Venatech ready-stock snapshot dated 9 November 2026.
Frequently asked questions
What are Alberta’s new data centre rules?
Reported on 18 November 2026, they would bar data centres of 10 MW or more within 600 metres of the nearest home and from prime or irrigated farmland, set a near-zero cooling-water standard and raise maximum fines. They apply only if passed.
How many Alberta data centre projects are affected?
The minister said about 30 percent of roughly 60 proposed projects, the Red Deer Advocate reported. The Logic reported that advanced projects would be grandfathered.
What MOV varistor voltage suits a 347 V circuit in Canada?
Start with a continuous rating 10 to 15 percent above nominal, which points to 390 VAC or 420 VAC. Walsin lists 34 MOVs in that band; check the clamping voltage on the datasheet and confirm with your certification engineer.
How many Walsin MOV varistors are rated 385 VAC or more?
We counted 116 distinct part numbers, from 390 VAC to 750 VAC, across the D, E, V and Industrial series, with peak currents from 400 A to 80,000 A.
Are Walsin MOV varistors in stock in Hong Kong?
The high-voltage MOVs are supplied to order. Request a quote and we source them through our authorised Walsin channel, confirming availability, date code and lead time on each quote.
Is Venatech an authorised Walsin distributor for buyers in Canada?
Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Canada in small lots. Stackpole and Viking are lines we supply, not authorised lines.