NEWS

EU Battery Regulation 2027 in France: Removable Portable Batteries From 18 February 2027, and Walsin Lists 2,913 Current Sense Resistors at 100 Milliohms or Less

Under the EU Battery Regulation 2027 milestones, portable batteries must be user-removable from 18 February 2027. For French teams redesigning a pack or its fuel gauge, Walsin Technology (Walsin) lists 2,913 current sense resistors at 100 milliohms or less, six of them a 10 milliohm, 1 percent, 1206 fit. Venatech, the authorised Walsin distributor in Hong Kong, crosses them.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for battery-pack and power engineers in France working on phones, tools, garden equipment, e-bikes and scooters. It is a perspective on the engineering that follows a regulatory date, not legal advice: what your product must do is for your compliance team. What we can do is show what Walsin covers when the measurement electronics around a battery move, and we re-measured Walsin’s chip-resistor export (Venatech_ChipR_Upload_01.xlsx onward, 234,378 distinct part numbers) and our stock list as at 9 November 2026 on 16 November 2026.

What does the EU Battery Regulation require from 18 February 2027?

Removability, and a QR code. CMS summarised on 25 November 2025 that from 18 February 2027 under Regulation (EU) 2023/1542, portable batteries must be removable and replaceable by the end user, batteries for light means of transport must be replaceable by an independent professional, and all batteries must carry a QR code.

The same CMS timeline says the QR code on electric-vehicle, light-transport and industrial batteries above 2 kWh should link to the digital battery passport, that due diligence obligations were postponed to 18 August 2027, and that minimum performance and durability values for rechargeable industrial batteries above 2 kWh follow on 18 August 2027. The regulation has exceptions and later amendments; check the current text, and how it applies to your product, with your compliance team.

Why does a removable battery change the electronics in a French product?

Because the measurement point can move. When a sealed battery becomes user-removable, many designs move the fuel gauge or protection circuit into the removable pack, or add a second sense point on the device side, and each sense point needs a low-ohm current sense resistor, typically 1 to 50 milliohms, with a tight tolerance and a low TCR.

We make no claim about how any French maker will respond, and the regulation does not tell you where to put a gauge. The engineering effect is predictable, though: a connector now sits in the current path, the pack may be hot-swapped, and the gauge needs to keep counting accurately after a battery that has lived in a drawer is put back in. That puts the shunt resistor’s tolerance, TCR and pulse rating on the review list. Our note on passives for a battery management system covers the rest of the pack BOM, and the chip resistor range lists every Walsin family.

How many current sense resistors does Walsin list at 100 milliohms or less?

2,913 part numbers. We counted 2,913 distinct Walsin chip resistors at 100 milliohms or less in the export: 1,761 in the thick-film low-ohm current sense group, 1,144 in the metal low-ohm current sense group, and 8 high-power or wide-terminal parts. Of them, 875 sit in series Walsin names as automotive.

Walsin series group, 100 milliohms or less Part numbers Typical use
Thick film low-ohm current sense 1,761 Over-current trip, charger current limit
Metal low-ohm current sense (plate and foil) 1,144 Fuel gauge, coulomb counting, motor current
Thick film high power and wide terminal 8 Power paths with high dissipation
Total 2,913

The split matters more than the total. Thick-film parts are fine for a trip threshold, but their TCR runs to hundreds or thousands of ppm per degree; in the export, 568 low-ohm rows state ±50 ppm. Our pillar on low-ohm current sense: thick film vs metal explains why a gauge wants metal.

Which Walsin parts cross a 10 milliohm, 1 percent, 1206 fuel-gauge shunt?

Six, all metal. We filtered the export for 10 milliohms, 1 percent, 1206 and a TCR of ±50 ppm and found six parts: WW12DR010FTL and WW12DR010FTLJ (metal foil, 1 W), WW12MR010FTL and WW12MR010FTLJ (metal plate, half a watt) and WW12NR010FTL and WW12NR010FTLJ (metal plate, 1 W).

Across all tolerances and TCRs, Walsin lists 111 parts at exactly 10 milliohms, 29 of them in 1206. The table shows the six against parts that match on value but not on TCR. Fill the last column with your incumbent.

Walsin part Construction Tolerance TCR (ppm/°C) Rated power Match / mismatch with a 10 milliohm, 1%, 1206 gauge shunt Your incumbent
WW12DR010FTL Metal foil 1% ±50 1 W Match
WW12NR010FTL Metal plate 1% ±50 1 W Match
WW12MR010FTL Metal plate 1% ±50 1/2 W Match, check dissipation
WW12MR010FTLJ Metal plate, automotive 1% ±50 1/2 W Match, automotive series for light vehicles
WW12DR010DTL Metal foil 0.5% ±50 1 W Match, tighter tolerance
WW12KR010FTL Metal plate 1% ±70 1 W Mismatch on TCR: ±70 against ±50
WW12WR010FTL Thick film 1% ±1000 1/3 W Mismatch: TCR too high for a gauge

At 10 milliohms and 5 A, a shunt dissipates a quarter of a watt, so the half-watt part works for a phone or tool pack but leaves little margin for an e-bike peak. Use Kelvin sense pads, and confirm against both datasheets and qualify in your own circuit.

What should a French engineer check on the battery side of a redesign?

Four things beyond the shunt. For a removable-battery redesign, check the shunt’s pulse rating against a hot-plug inrush, ESD and surge protection on the new pack connector, the TCR of the gauge shunt across the pack’s real temperature range, and the date-code traceability of every part in the pack, because the QR code from 18 February 2027 points to information about the battery.

Walsin’s anti-surge chip resistors and varistors cover the connector side; see anti-surge chip resistors. On the gauge, a 1 W metal part in 1206 keeps the footprint small while handling a short peak. Keep the date code and lot on the pack’s build record. We supply original sealed Walsin packaging and a certificate of conformity per shipment on request, which is the kind of record a compliance team asks for.

Which current sense resistors are on the Hong Kong shelf?

Three thick-film sense lines. Our stock list as at 9 November 2026 holds three Walsin thick-film current sense resistors in 0805: WW08WR270FTL (0.27 ohm), WW08WR390FTL (0.39 ohm) and WW08WR470FTL (0.47 ohm), all 1 percent, on our shelf in Hong Kong (snapshot 9 Nov 2026).

We checked all three against the export’s current sense group. They suit charger current-limit and USB power-path sensing on a bench build. The metal 10 milliohm parts in the table are to order: request a quote and we source them through our authorised Walsin channel. The ready-stock list is a dated snapshot, never live-synced, and we make no stock or lead-time promise.

How Venatech helps

How Venatech helps is a shunt cross with TCR on every row. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, so a pack BOM’s shunts return Walsin candidates with tolerance, TCR and power stated.

Paste your current sense resistor codes into the cross-reference tool, or upload the whole pack BOM and request a quote. Check the ready-stock snapshot, dated 9 November 2026. We serve French design teams and EMS buyers from Hong Kong, in small lots with fast quotes. Walsin is our authorised line; Stackpole and Viking are lines we supply. We give no legal, customs or compliance advice on the Battery Regulation; confirm that with your compliance team.

The short version

CMS summarised the EU Battery Regulation 2027 milestones on 25 November 2025: from 18 February 2027 portable batteries must be user-removable and every battery needs a QR code. A removable pack often moves the fuel gauge. Walsin covers that with 2,913 current sense resistors at 100 milliohms or less, six of them a metal 10 milliohm, 1 percent, 1206 gauge fit.

Send us your pack’s shunt and protection parts, and we will return Walsin crosses with TCR and power stated. Which sense resistor in your pack runs closest to its rated power?

Related reading

Last reviewed: 16 November 2026

Sources

Fetched 16 November 2026.

  • CMS, “EU Sustainable Batteries Regulation: Where are we now?”, 25 November 2025: https://cms.law/en/svk/legal-updates/eu-sustainable-batteries-regulation-where-are-we-now
  • Walsin chip-resistor export, Venatech_ChipR_Upload_01.xlsx onward, re-measured 16 November 2026, with the Walsin datasheet links it carries; Venatech stock list as at 9 November 2026.

Frequently asked questions

What changes under the EU Battery Regulation on 18 February 2027?

CMS summarises that from 18 February 2027 portable batteries must be removable and replaceable by the end user, light-transport batteries must be replaceable by an independent professional, and all batteries must carry a QR code. Confirm details with your compliance team.

Does the EU Battery Regulation apply to products sold in France?

It is an EU regulation, so it applies in France as in every member state. How it applies to a given product is a question for your compliance team; Venatech gives no legal advice.

How many current sense resistors does Walsin offer at 100 milliohms or less?

We counted 2,913 distinct Walsin parts at 100 milliohms or less: 1,761 thick-film and 1,144 metal current sense, plus 8 high-power parts. Venatech crosses and quotes them for French teams from Hong Kong.

Which Walsin resistor crosses a 10 milliohm 1 percent 1206 shunt for a fuel gauge?

Six metal parts at ±50 ppm: WW12DR010FTL, WW12DR010FTLJ, WW12MR010FTL, WW12MR010FTLJ, WW12NR010FTL and WW12NR010FTLJ. Confirm against both datasheets and qualify in your own circuit.

Why use a metal current sense resistor for a battery fuel gauge?

Because a gauge integrates current over hours, and a thick-film part’s TCR of hundreds of ppm per degree adds drift as the pack warms. Metal plate and foil parts in Walsin’s export state ±50 ppm or ±70 ppm.

Is Venatech an authorised Walsin distributor for buyers in France?

Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in France in small lots. Stackpole and Viking are lines we supply, not authorised lines.


Share This, Choose Your Platform!