NEWS

High Temperature MLCC for Burn-In Boards in Clark, the Philippines: 235 Walsin Parts Rated to 150 °C

A high temperature MLCC is a ceramic capacitor rated above the usual 125 °C, the kind a burn-in board needs when it lives inside an oven. Walsin lists 235 MLCC rated to 150 °C: 128 in its HT series, 104 in its RF series and 3 in MT. Venatech is the authorised Walsin distributor in Hong Kong.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for test, burn-in and hardware engineers and the buyers who support them at semiconductor and electronics firms in Clark Freeport Zone, Pampanga and across Central Luzon. Walsin Technology (Walsin) is the line we are authorised for. We parsed our MLCC upload files, Venatech_MLCC_Upload_01.xlsx to Venatech_MLCC_Upload_08.xlsx, on 17 November 2026: 23,360 distinct part numbers. We sorted every one by its listed operating temperature range and read the 150 °C parts against Walsin’s datasheets WTC_MLCC_High_Temperature_HT.pdf, WTC_MLCC_Microwave_RF.pdf and WTC_MLCC_Automotive_MT.pdf. Every part number below is real.

How big is the semiconductor industry in Clark?

Large enough to export billions. SunStar reported on 8 July 2026 that semiconductor and electronics exports from Clark reached 3.8 billion US dollars in 2025, and that as of March 2026 the freeport hosted 22 semiconductor companies employing 4,289 workers.

The report, a Clark Development Corporation release, says the CDC met its semiconductor and electronics locators on 7 July to discuss workforce, importation and regulatory issues; it names no companies and does not describe their processes, so we do not either. What a component buyer can take from it is scale and focus: 22 chip firms in one zone means test floors, reliability labs and the fixtures, load boards and burn-in boards that go with them, all of which consume passives that most consumer boards never see.

Why do burn-in and test boards need a high temperature MLCC?

Because the board sits in the chamber with the devices. Burn-in stresses packaged chips at high temperature, often 125 °C, for hours at a time, and the decoupling and filter capacitors on the board share that heat cycle after cycle; a part rated to 150 °C keeps 25 °C of margin where a 125 °C part has none.

At its rated limit, a standard X7R MLCC is working at the edge of its specification, and repeated cycling to that edge is where drift and cracking start to show. A 150 °C rating gives headroom for chamber overshoot, local self-heating from the devices and long dwell times. The same logic applies to high-temperature test sockets and engine-bay or downhole electronics. Our guide to Walsin’s HT series to 150 °C covers the family in detail.

How many Walsin MLCC are rated to 150 °C?

235 of 23,360. We counted 235 distinct Walsin MLCC with a listed range of minus 55 °C to plus 150 °C: 128 in the HT series (102 X8G and 26 X8R), 104 in the RF microwave series, all X8G, and 3 in the AEC-Q200 MT series, also X8G.

Walsin MLCC rated to 150 °C Dielectric Sizes Values Voltages Parts
HT series X8R 0603, 0805, 1206 100 pF to 100 nF 50 V 26
HT series X8G 0402 to 1210 1 pF to 15 nF 50 V, 100 V 102
RF series X8G 0603, 0805 0.2 pF to 82 pF 250 V, 500 V 104
MT series (AEC-Q200) X8G 0402 18 pF 50 V 3
Total 235

Everything else in the extract stops at 125 °C or below: 22,277 parts at 125 °C, 125 at 105 °C and 723 at 85 °C. By size, the 128 HT parts split 37 in 0805, 33 in 1206, 31 in 0603, 20 in 1210 and 7 in 0402. We have not seen Walsin’s 150 °C range counted across all three series anywhere else.

Which Walsin parts cross a 10 nF, 0805, 50 V brief rated to 150 °C?

Two match. For 10 nF, 0805, 50 V and a 150 °C rating, HT21R103K500 (X8R, 10 percent) and HT21G103J500 (X8G, 5 percent) fit; the 0603 and 1206 HT parts miss on size, and Walsin’s 125 °C X7R parts miss on temperature.

Brief: 10 nF, 0805, 50 V, rated to 150 °C Walsin part Series, dielectric Match / mismatch Your incumbent
Direct fit HT21R103K500 HT, X8R, ±10% Match; 1.25 mm thick
Stable dielectric HT21G103J500 HT, X8G, ±5% Match; 1.25 mm thick
Bigger case HT31R103K500 HT, X8R Mismatch in size (1206)
Smaller case HT18R103K500 HT, X8R Mismatch in size (0603)
Automotive X7R MT21B103K500 MT, X7R Mismatch in temperature (125 °C)
General purpose 0805B103K500 General purpose, X7R Mismatch in temperature (125 °C)

Check the height as well as the rating: both HT matches list 1.25 ±0.10 mm, while the two X7R parts list 0.80 ±0.10 mm, which matters under a socket lid or a tight board-to-board gap. Leave the last column for your current part. Our guide to how to cross-reference an MLCC sets out the order of checks.

When is X8G the better choice than X8R on a hot board?

When the value is small and stability matters more than capacitance. Walsin’s X8R parts reach 100 nF in 1206 and are the choice for decoupling at 150 °C; its X8G parts stop at 15 nF but suit timing, filter and RF positions where a capacitance that moves little with temperature is the point.

X8R is defined by a capacitance change of no more than 15 percent across minus 55 °C to plus 150 °C, so a 10 nF X8R part may read a little lower at the peak of a burn-in profile. On a supply rail that is usually acceptable; on a filter corner it may not be. The RF-series X8G parts add 250 V and 500 V ratings at 0.2 pF to 82 pF for hot RF or high-voltage test positions. On the shelf, three lines rated to 150 °C are on our shelf in Hong Kong (snapshot 9 Nov 2026): HT21G331K500 and HT21G472K500 in the HT series and RF21G8R2C251 in the RF series. The other parts are to order: request a quote and we source them through our authorised Walsin channel. The MLCC range page lists every series.

How Venatech helps: what can we supply to a Clark semiconductor team?

Crosses for the whole fixture or burn-in board, in one pass. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, including all 235 Walsin MLCC rated to 150 °C.

Paste your capacitor lines into the cross-reference tool, upload the board’s BOM at /bom/, or see the dated ready stock list. We serve the Philippines from Hong Kong in small lots, which suits board builds and fixture repairs, and we quote fast. We confirm availability, date code and lead time on each quote and promise none in advance; qualification stays with your reliability team, and import questions with your compliance team.

The short version

  • Clark’s semiconductor and electronics exports reached 3.8 billion US dollars in 2025, with 22 semiconductor firms and 4,289 workers as of March 2026 (SunStar, 8 July 2026).
  • Walsin lists 235 MLCC rated to 150 °C: 128 HT, 104 RF and 3 MT.
  • For 10 nF, 0805, 50 V at 150 °C, HT21R103K500 and HT21G103J500 match; both are 1.25 mm thick.
  • X8R reaches 100 nF for decoupling; X8G stops at 15 nF but holds its value.

Send us the capacitors from your burn-in or load board and we will return the 150 °C Walsin crosses with every difference stated. How close to 125 °C do your chambers actually run?

Related reading

Last reviewed: 17 November 2026.

Sources

Fetched 17 November 2026.

  • SunStar, Clark semiconductor exports reach 3.8 billion US dollars, Clark Development Corporation release, 8 July 2026: https://www.sunstar.com.ph/pampanga/clark-semicon-exports-reach-us38-b-cdc
  • Venatech MLCC upload files Venatech_MLCC_Upload_01.xlsx to _08.xlsx and Walsin’s WTC_MLCC_High_Temperature_HT.pdf, WTC_MLCC_Microwave_RF.pdf, WTC_MLCC_Automotive_MT.pdf and WTC_MLCC_General_Purpose.pdf datasheets as linked in the export, re-measured 17 November 2026; Venatech ready stock snapshot dated 9 November 2026.

Frequently asked questions

How many Walsin MLCC are rated to 150 °C?

235 in our count of 17 November 2026: 128 in the HT series, 104 in the RF series and 3 in the MT series. The rest of Walsin’s 23,360 MLCC stop at 125 °C or below.

Which Walsin part is a 10 nF, 0805, 50 V capacitor rated to 150 °C?

HT21R103K500 in X8R at 10 percent, or HT21G103J500 in X8G at 5 percent. Both are 1.25 mm thick; check clearance and DC bias against both datasheets.

What is the highest-value X8R capacitor Walsin makes?

100 nF, as HT31R104K500 in 1206 at 50 V. Walsin’s X8R parts run from 100 pF to 100 nF in 0603, 0805 and 1206.

Do burn-in boards need 150 °C capacitors?

If the chamber runs at or near 125 °C, a 150 °C part gives margin that a 125 °C part does not. Take the profile from your own reliability specification.

Does Venatech stock high temperature MLCC for the Philippines?

We hold stock in Hong Kong. Three lines rated to 150 °C are on our shelf in Hong Kong (snapshot 9 Nov 2026); the other HT and RF parts are quoted through our authorised Walsin channel.

Can Venatech supply semiconductor firms in Clark, the Philippines?

Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to the Philippines. Use the cross-reference tool or upload a BOM; confirm import rules with your compliance team.


Share This, Choose Your Platform!