For a high voltage chip resistor in a solar inverter or storage PCS in Vietnam, Walsin Technology (Walsin) lists 20,244 high voltage thick film parts in five case sizes, 4,118 of them in 2512, from 47 ohm to 100 megohm. Venatech, Walsin’s authorised distributor in Hong Kong, crosses your divider resistor and quotes the Walsin line.
Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for engineers in Vietnam who design, build or source PV inverters, power conversion systems, battery storage controllers and energy-management boxes for local solar projects. The news fact names its source and date. The counts are ours: we parsed Walsin’s chip resistor exports, Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_34.xlsx, and read the high voltage rows against the datasheet each row points to: ASC_WFxxV.pdf, ASC_WKxxV.pdf and ASC_WFxxN.pdf.
What did Vietnam decide on solar power price ceilings in November 2026?
Higher ceilings, and a premium for storage. pv magazine reported on 10 November 2026, in a story republished by Now.Solar on 12 November, that Vietnam’s Ministry of Industry and Trade approved new regional maximum prices for ground-mounted and floating solar, effective 5 November 2026.
Without storage, ground-mounted ceilings run from VND 1,104.32 per kWh in the south to VND 1,591.02 in the north, and floating solar from VND 1,340.21 to VND 1,939.74. Projects with batteries get higher ceilings, up to VND 1,813.48 for ground-mounted and VND 2,120.31 for floating plants in the north, if storage is at least 10 percent of plant capacity with two hours of duration. The same report says ceilings without storage rose about 15.1 percent in the north, 16.8 percent in the central region and 9.1 percent in the south, and that Vietnam’s solar fleet passed 19 GW by the end of 2025. For an engineer, the signal is that a solar plant with a battery now earns a better maximum price, which favours hybrid inverters and PCS hardware that handle both.
Why does a solar inverter or storage PCS need a high voltage chip resistor?
Because something has to measure and bleed a high DC voltage. A high voltage chip resistor is built to hold more voltage across one part than a general purpose chip; Walsin publishes them up to 100 megohm, so a short string can sense or discharge a 1,000 V or 1,500 V DC link.
In a PV inverter the DC link sits at the string voltage. The controller needs to read it, for maximum power point tracking and for protection, through a resistor divider. The same link needs a bleeder that discharges the bulk capacitors after shutdown, and insulation-monitoring circuits use high-value strings between the DC bus and earth. A battery PCS adds a second high voltage bus on the battery side. General purpose resistors fail here on working voltage per part. Our post on high voltage chip resistors and the limit nobody checks explains that limit, and the chip resistor range lists every part.
How many high voltage chip resistors does Walsin list, and in which sizes?
Twenty thousand two hundred and forty-four. We counted 20,244 distinct part numbers in Walsin’s Thick Film High Voltage Chip Resistor group, across 0603, 0805, 1206, 2010 and 2512; the three larger sizes hold 4,118 parts each, and 2512 parts are rated 1 W.
| Case size | Part numbers | Rated power in the export |
|---|---|---|
| 0603 (1608) | 3,924 | 1/10 W |
| 0805 (2012) | 3,966 | 1/8 W |
| 1206 (3216) | 4,118 | 1/4 W |
| 2010 (5025) | 4,118 | 1/2 W |
| 2512 (6432) | 4,118 | 1 W |
| Total | 20,244 |
By tolerance, 11,497 are ±1 percent, 3,045 are ±0.5 percent, 3,045 are ±2 percent and 2,657 are ±5 percent. The group splits into four series: the standard high voltage parts (10,437), an automotive version (6,803), and a UL safety series with an automotive twin (1,502 each). We have not seen the high voltage range counted by size and tolerance this way elsewhere.
Which Walsin part fits a 1 megohm, 2512, 0.5 percent divider brief?
One part matches exactly. For a DC link divider brief of 1 megohm, 2512 and ±0.5 percent, WK25V1004DTL matches; WK25V1004FTL, WF25V1004FTL and the UL-series WF25N1004FTL are ±1 percent alternatives at the same value and size.
Put your incumbent part in the last column and compare each field.
| Walsin part | Series | Size | Value | Tolerance | TCR (ppm/°C) | Match / mismatch with 1 megohm, 2512, ±0.5% | Your incumbent |
|---|---|---|---|---|---|---|---|
WK25V1004DTL |
High voltage | 2512 | 1 megohm | ±0.5% | ±100 | Match | |
WK25V1004FTL |
High voltage | 2512 | 1 megohm | ±1% | ±100 | Mismatch: tolerance; fits a ±1% brief | |
WF25V1004FTL |
High voltage | 2512 | 1 megohm | ±1% | ±100 | Mismatch: tolerance; fits a ±1% brief | |
WF25N1004FTL |
UL safety | 2512 | 1 megohm | ±1% | ±100 | Mismatch: tolerance; fits where a UL-certified series is asked for, confirm the file on the datasheet | |
WK25V1004FTLJ |
High voltage, automotive | 2512 | 1 megohm | ±1% | ±100 | Mismatch: tolerance; automotive documentation | |
WK25V1004GTLJ |
High voltage, automotive | 2512 | 1 megohm | ±2% | ±100 | Mismatch: tolerance | |
WK12V1004DTL |
High voltage | 1206 | 1 megohm | ±0.5% | ±100 | Mismatch: case size; lower voltage per part |
In a divider, the ratio matters more than each value, so two ±0.5 percent parts from one reel often beat a mixed string. Confirm against both datasheets and qualify in your own circuit.
Check the datasheet. Maximum working voltage and maximum overload voltage for each size are on Walsin’s ASC_WKxxV.pdf, ASC_WFxxV.pdf and ASC_WFxxN.pdf datasheets, not in the export. Take them from the datasheets before setting the number of parts in a string.
How many resistors does a 1,500 V DC link divider need?
Set by working voltage per part, not by power. A string of six 1 megohm 2512 resistors across 1,500 V puts about 250 V on each part and dissipates about 0.375 W in total, about 63 mW each, far inside a 1 W rating; the count is set by each part’s voltage rating plus your margin.
Work it in this order: take the highest DC link voltage including open-circuit string voltage on a cold morning, divide by the datasheet working voltage of the chosen size, add margin, and round up. Then check creepage on the board between the ends of the string, because a chip that holds the voltage can still flash over a dirty or humid surface. A 1206 string needs more parts than a 2512 string for the same voltage, and each extra joint is a failure point.
Can Venatech supply Walsin high voltage resistors from Hong Kong?
Yes, to order. All 20,244 Walsin high voltage chip resistors can be quoted from Hong Kong: none is on our shelf in the snapshot dated 9 November 2026, so request a quote and we source them through our authorised Walsin channel.
Each quote states availability, date code and lead time for the line, and we work in small lots for prototypes, certification builds and pilot runs. We make no stock, price or lead-time promise. The ready-stock list, a dated snapshot, covers MLCC and chip resistors that sit on the same control board.
How Venatech helps: what should a Vietnamese inverter team send us?
The divider, bleeder and sense parts from your BOM. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.
Paste a resistor code into the cross-reference tool, or upload the whole BOM and request a quote through the site. The ready-stock snapshot is dated 9 November 2026. We serve Ho Chi Minh City, Binh Duong, Hai Phong and Bac Ninh from Hong Kong, with fast quotes and small lots. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply. We give no advice on Vietnam’s power purchase rules; confirm those with your own team.
The short version
Vietnam’s Ministry of Industry and Trade raised solar price ceilings from 5 November 2026 and kept a premium for plants with at least 10 percent, two-hour storage, up to VND 2,120.31 per kWh for floating solar in the north, pv magazine reported on 10 November. Hybrid inverters and PCS units need high voltage chip resistors to sense and bleed their DC links. Walsin covers the job with 20,244 high voltage parts, 4,118 in 2512, and WK25V1004DTL meets a 1 megohm, ±0.5 percent divider brief exactly.
Send us the high voltage resistors on your inverter and we will return Walsin crosses with every difference stated. What is the highest open-circuit voltage your DC link has to read?
Related reading
- High voltage chip resistors and the limit nobody checks
- Chip resistor power rating by case size
- Cross-referencing chip resistors to Walsin
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 17 November 2026.
Sources
Fetched 17 November 2026.
- Now.Solar, republishing pv magazine, report on Vietnam’s 2026 solar price ceilings and storage premiums, 12 November 2026 (pv magazine original dated 10 November 2026): https://now.solar/2026/11/12/vietnam-increases-solar-tariffs-for-2026-maintains-storage-premiums-pv-magazine-global/
- Walsin chip resistor exports, Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_34.xlsx, re-measured 17 November 2026; Walsin ASC_WKxxV.pdf, ASC_WFxxV.pdf and ASC_WFxxN.pdf datasheets; Venatech Hong Kong stock snapshot dated 9 November 2026.
Frequently asked questions
What are Vietnam’s new solar price ceilings?
pv magazine reported on 10 November 2026 that the Ministry of Industry and Trade set ground-mounted ceilings from VND 1,104.32 to VND 1,591.02 per kWh, effective 5 November. Plants with storage get up to VND 2,120.31 per kWh for floating solar in the north.
What does a high voltage chip resistor do in a solar inverter?
It senses and bleeds the high DC link voltage. It holds more voltage per part than a general purpose chip, so fewer parts are needed in a divider or bleeder string.
How many high voltage chip resistors does Walsin list?
We counted 20,244 in five case sizes from 0603 to 2512. The 1206, 2010 and 2512 sizes hold 4,118 parts each.
Which Walsin part crosses a 1 megohm 2512 resistor at 0.5 percent?
WK25V1004DTL matches 1 megohm, 2512 and ±0.5 percent. WK25V1004FTL and WF25V1004FTL are ±1 percent alternatives; confirm the working voltage on each datasheet.
How many 1 megohm resistors does a 1,500 V divider need?
It depends on each part’s rated working voltage. Six 2512 parts put about 250 V on each and dissipate about 63 mW each; check the datasheet voltage and add margin before fixing the count.
Can Venatech supply Walsin high voltage resistors to Vietnam from Hong Kong?
Yes. Venatech Limited is an authorised Walsin distributor in Hong Kong. Request a quote and we source them through our authorised Walsin channel, with availability, date code and lead time stated on each quote.