NEWS

PLL Loop Filter Capacitor for Automotive Radar in Portugal: Bosch Braga Doubles to 10 Million Radars and 1,287 Walsin AEC-Q200 C0G Parts

A PLL loop filter capacitor should be C0G, not X7R, on any board that vibrates: X7R is piezoelectric and turns vibration into phase noise. Walsin lists 1,287 C0G capacitors in its AEC-Q200 MT and ST series, up to 10 nF in 0603. Venatech is the authorised Walsin distributor in Hong Kong.


Venatech Limited, an authorised Walsin distributor in Hong Kong, wrote this for RF, radar and clock design engineers in Braga, the Minho and the rest of Portugal who lay out frequency synthesizers on boards that ride in vehicles, machines and outdoor housings. Walsin Technology (Walsin) is the line we are authorised for. We parsed our eight MLCC upload files, Venatech_MLCC_Upload_01.xlsx to Venatech_MLCC_Upload_08.xlsx, on 19 November 2026 and counted distinct C0G part numbers by case, voltage and series, reading them against Walsin’s datasheets WTC_MLCC_Automotive_MT.pdf and WTC_MLCC_General_Purpose.pdf. Every part number below is real.

What is Bosch doing with radar production in Braga?

Doubling it. Portugal Global reported on 13 April 2026 that Bosch is investing twenty-five to thirty million euros at its Braga plant to double radar sensor production, raising the lines from three to six and installed capacity from about five and a half million radars last year to 10 million a year.

The report places the plant in Bosch’s mobility electronics division. It does not name products, frequencies or suppliers, so we quote none. For engineers nearby, the point is scale: millions of radar boards a year built in northern Portugal, each one carrying a frequency synthesizer, each one bolted into a vehicle that vibrates for its whole life. That combination is where the dielectric of one small capacitor starts to matter.

Which capacitor type should a PLL loop filter use?

C0G (NP0) wherever the value allows. Texas Instruments’ clock evaluation module user guide SNAU297, dated July 2025, describes X7R as sensitive to vibration through the piezoelectric effect and recommends non-ferroelectric capacitors such as NP0, C0G or tantalum for performance under vibration.

The loop filter sets the PLL’s bandwidth and its phase margin, and it sits on the most sensitive node in the synthesizer: the control voltage of the VCO. Anything that disturbs the charge on those capacitors shows up directly as frequency modulation of the output. C0G holds its value over temperature and voltage, has very low dielectric absorption and almost no piezoelectric response, so it disturbs nothing. The TI guide adds that C0G is commonly available in 0805 up to 47 nF and suggests tantalum from 0.1 µF upward. Our NP0 versus X7R versus X5R explainer sets the dielectrics side by side.

Why does an X7R loop filter capacitor add phase noise under vibration?

Because it works as a microphone. X7R uses barium titanate, which is piezoelectric: mechanical stress from vibration or shock generates a small voltage across the capacitor, and on a loop filter that voltage modulates the VCO tuning line, appearing as spurs and raised phase noise at the vibration frequencies.

In a radar, phase noise close to the carrier blurs the separation between targets at similar ranges and speeds, and vibration-induced spurs can look like targets that are not there. The effect scales with the stress on the part and the sensitivity of the VCO, so a design that passes on a bench can degrade on a shaker table or in a car. Bias makes it worse: X7R also loses capacitance with DC voltage, which moves the loop bandwidth itself. Our DC bias guide shows by how much.

Check the datasheet. The size of the effect depends on your VCO gain and loop bandwidth. Run the loop filter calculation for your own synthesizer, then confirm the C0G part’s tolerance and rated voltage in Walsin’s WTC_MLCC_Automotive_MT.pdf.

How large can a C0G loop filter capacitor be in Walsin’s range?

10 nF in 0603, 22 nF in 0805, 100 nF in 1206. We found Walsin’s C0G range topping out at 1 nF in 0402, 10 nF in 0603, 22 nF in 0805 and 100 nF in 1206 and larger, with 3,238 C0G parts in 0603 alone; in the automotive MT series, 0603 also reaches 10 nF.

Walsin C0G ceiling, by case Largest C0G value C0G parts in that case
0402 1 nF 2,994
0603 10 nF 3,238
0805 22 nF 3,003
1206 and larger 100 nF 24 parts at 100 nF

Most integer-N and fractional-N loop filters need a few hundred picofarads to a few tens of nanofarads, which falls inside 0603 and 0805. If your calculation asks for 47 nF or more, either widen the case, split the capacitor, or revisit the loop bandwidth; a high-value X7R at that position is the choice to avoid on a vibrating board.

How many AEC-Q200 C0G capacitors does Walsin list?

1,287. We counted 1,287 distinct C0G parts in Walsin’s AEC-Q200 automotive series, 1,284 in MT and 3 in ST, and 1,314 C0G parts of all series between 100 pF and 100 nF in 0402 and 0603 combined.

For a radar board that must meet automotive rules, MT is the starting point; it covers the loop filter range from picofarads up to 10 nF in 0603. Tolerance matters for loop stability more than many designers expect: a 10 percent part moves the loop’s zero and pole, and with it the phase margin. Walsin offers C0G at 1, 2 and 5 percent; across the whole C0G catalogue we counted at least 3,528 parts at 1 or 2 percent.

Which Walsin parts fit a 4.7 nF, 0603, C0G loop filter brief?

Two match. For 4.7 nF, C0G, 0603, ±5%, at least 50 V and AEC-Q200, MT18N472J500 and MT18N472J101 are fits; the general purpose parts match the value but carry no AEC-Q200 qualification, and the X7R part is the wrong dielectric for this position.

Brief: 4.7 nF, C0G, 0603, ±5%, ≥ 50 V, AEC-Q200 Walsin part Series Match / mismatch Your incumbent
Direct fit MT18N472J500 MT automotive Match, 50 V
Higher voltage MT18N472J101 MT automotive Match, 100 V
Commercial, same value 0603N472J500 General purpose Mismatch: no AEC-Q200 qualification
Commercial, tighter 0603N472G500 General purpose Mismatch: ±2% but no AEC-Q200
On our shelf 0603N472J250 General purpose Mismatch: 25 V, no AEC-Q200
Wrong dielectric MT18B472J500 MT automotive, X7R Mismatch: X7R, piezoelectric

Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.

Leave the last column for your current part. On a bench prototype, the shelf part 0603N472J250 behaves the same in the loop; for production on an automotive line, use the MT rows.

How Venatech helps: what can we supply to a radar or RF team in Portugal?

The loop filter, the decoupling around the synthesizer and the RF capacitors, crossed in one pass. Venatech is the authorised Walsin distributor in Hong Kong; VenaMatch decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, including all 1,287 AEC-Q200 C0G parts.

0603N472J250 is on our shelf in Hong Kong (snapshot 9 Nov 2026), along with 375 other C0G lines; the MT parts are to order, so request a quote and we source them through our authorised Walsin channel. Paste your capacitor lines into the cross-reference tool, upload a BOM at /bom/, or see the dated ready stock list. The MLCC range page lists every series. We serve Portugal from Hong Kong in small lots and quote fast. We confirm availability, date code and lead time on each quote and promise none in advance; qualification stays with your engineers, and import questions with your compliance team.

The short version

  • Bosch is doubling radar sensor capacity at Braga to 10 million a year, from three lines to six (Portugal Global, 13 April 2026).
  • X7R is piezoelectric; on a PLL loop filter, vibration becomes phase noise. Use C0G (TI, July 2025).
  • Walsin’s C0G reaches 10 nF in 0603, 22 nF in 0805 and 100 nF in 1206; 1,287 C0G parts are AEC-Q200.
  • For 4.7 nF, 0603, C0G, AEC-Q200, MT18N472J500 and MT18N472J101 match.

Send us your synthesizer’s loop filter values and we will return the Walsin C0G crosses with every difference stated. Has your radar board been on a shaker table with the loop filter you built it with?

Related reading

Last reviewed: 19 November 2026.

Sources

Fetched 19 November 2026.

  • Portugal Global (AICEP), Bosch Braga invests up to 30 million euros to double radars production, 13 April 2026: https://portugalglobal.pt/en/news/2026/abril/bosch-braga-invests-up-to-30m-to-double-radars-production/
  • Texas Instruments, clock evaluation module user guide SNAU297, section 5.3.1, July 2025: https://www.ti.com/lit/pdf/snau297
  • Venatech MLCC upload files Venatech_MLCC_Upload_01.xlsx to _08.xlsx and Walsin’s WTC_MLCC_Automotive_MT.pdf and WTC_MLCC_General_Purpose.pdf datasheets as linked in the export, re-measured 19 November 2026; Venatech ready stock snapshot dated 9 November 2026.

Frequently asked questions

What capacitor should I use in a PLL loop filter?

C0G (NP0) wherever the value allows. It is stable, low-loss and not piezoelectric. Use film or tantalum for values beyond the C0G range.

Can I use X7R in a PLL loop filter?

On a still bench board it may work, but X7R is piezoelectric and loses capacitance with bias, so vibration and voltage both disturb the loop. Avoid it on boards that move.

What is the highest C0G capacitance in 0603?

10 nF in Walsin’s range, in both general purpose and the AEC-Q200 MT series. 0805 reaches 22 nF and 1206 reaches 100 nF.

How many AEC-Q200 C0G capacitors does Walsin make?

1,287 in our count of 19 November 2026: 1,284 in MT and 3 in ST.

Which Walsin part is a 4.7 nF, 0603, C0G, AEC-Q200 capacitor?

MT18N472J500 at 50 V or MT18N472J101 at 100 V, both 5 percent.

Can Venatech supply radar and RF electronics makers in Portugal?

Yes. Venatech is the authorised Walsin distributor in Hong Kong and quotes small lots to Portugal. Use the cross-reference tool or upload a BOM; confirm import rules with your compliance team.


Share This, Choose Your Platform!