For a high voltage chip resistor on 800 VDC rack power in Taiwan, Walsin Technology (Walsin) lists 2,070 high-voltage parts from 1 to 10 megohm at ±1% or ±0.5% and ±100 ppm, in 1206, 2010 and 2512. Venatech Limited, an authorised Walsin distributor in Hong Kong, crosses your divider parts and quotes them.
This post is for power engineers in Taiwan moving rack power from 54 V toward ±400 VDC and 800 VDC, and for the buyers who source their sensing parts. We counted the rows ourselves in Walsin’s chip resistor exports (Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_79.xlsx, 234,378 distinct part numbers) and read the high-voltage group against the ASC_WKxxV.pdf, ASC_WFxxV.pdf and ASC_WFxxN.pdf datasheets named in the export. The news figure carries its source and date.
What did Delta Electronics report for October 2026?
A record-pace month driven by AI power. TechNews reported on 9 November 2026 that Delta Electronics’ October consolidated revenue reached 74.666 billion New Taiwan dollars, up 30.1 percent year on year and 14.2 percent on September, with January to October revenue up 36.3 percent.
The same report says power and components made up 51 percent of October revenue and infrastructure 36 percent, and that AI-related business is about half of Delta’s revenue. It adds that Delta’s ±400 VDC power has been partly shipping since the third quarter, while 800 VDC is still in customer qualification and standardisation. Lite-On, in the same report, posted October revenue of 20.1 billion New Taiwan dollars, up 32 percent. We add no forecast and say nothing about either company’s suppliers. For an engineer in Taiwan the signal is clear enough: high-voltage DC is moving from slides to shipped racks, and every HVDC stage has to measure its own bus.
Why does an 800 VDC rack need a high voltage chip resistor?
Because the bus must be measured, and a normal chip resistor is not built for it. A high voltage chip resistor carries a higher rated working voltage per case size than a general-purpose part; an 800 VDC bus is sensed through a string of megohm resistors so that each part sees only a share of the voltage.
The divider feeds an ADC or an isolated amplifier that watches bus voltage for regulation, over-voltage protection, pre-charge and insulation monitoring. Three things decide the resistor: the voltage each part must stand off, the ratio accuracy over temperature, and the leakage the divider puts on the bus. A general-purpose 1206 part is limited by its working voltage long before its power rating matters, which is why designers reach for a dedicated high-voltage family. Our guide to high-voltage chip resistors and the limit nobody checks explains why the voltage limit, not wattage, sets the string length. The full chip resistor range lists every part.
How many Walsin high voltage chip resistors suit an 800 VDC divider?
Two thousand and seventy. We counted 2,070 distinct Walsin high-voltage chip resistors from 1 to 10 megohm, at ±1% or ±0.5% and ±100 ppm/°C, in 1206, 2010 and 2512; all 2,070 part numbers are written without a space.
| Case size | Rated power | ±0.5% | ±1% | Total |
|---|---|---|---|---|
| 1206 (3216) | 0.25 W | 115 | 575 | 690 |
| 2010 (5025) | 0.5 W | 115 | 575 | 690 |
| 2512 (6432) | 1 W | 115 | 575 | 690 |
| Total | 345 | 1,725 | 2,070 |
By family, 1,035 are WK..V parts (including automotive codes ending in J), 345 are WF..V parts and 690 are WF..N parts from the series Walsin lists as carrying UL safety certification. Across all sizes the Walsin high-voltage group holds 20,244 part numbers, so the brief above is a deliberately narrow slice of it. We have not seen this megohm, 1206-and-up slice of the range laid out this way elsewhere.
Which Walsin part fits a 1 megohm, 1 percent, 100 ppm divider brief?
Six parts meet it. For a brief of 1 megohm, ±1% or better, ±100 ppm/°C, 1206 or 2512, from a high-voltage series, WK12V1004DTL, WK12V1004FTL, WF12V1004FTL, WF12N1004FTL, WK25V1004FTL and WF25N1004FTL match.
Put your incumbent divider resistor in the last column and compare field by field.
| Walsin part | Value | Tolerance | TCR (ppm/°C) | Case, power | Match / mismatch with 1 megohm, ±1%, 100 ppm, 1206 or 2512 | Your incumbent |
|---|---|---|---|---|---|---|
WK12V1004DTL |
1 megohm | ±0.5% | ±100 | 1206, 0.25 W | Match, tighter tolerance | |
WK12V1004FTL |
1 megohm | ±1% | ±100 | 1206, 0.25 W | Match | |
WF12V1004FTL |
1 megohm | ±1% | ±100 | 1206, 0.25 W | Match; different family, check land pattern | |
WF12N1004FTL |
1 megohm | ±1% | ±100 | 1206, 0.25 W | Match; UL-listed series | |
WK25V1004FTL |
1 megohm | ±1% | ±100 | 2512, 1 W | Match; larger body, fewer parts per string | |
WF25N1004FTL |
1 megohm | ±1% | ±100 | 2512, 1 W | Match; UL-listed series | |
WK12V1004GTLJ |
1 megohm | ±2% | ±100 | 1206, 0.25 W | Mismatch: tolerance | |
WF06V1004FTL |
1 megohm | ±1% | ±100 | 0603, 0.1 W | Mismatch: case below 1206 | |
WK12V1005FTL |
10 megohm | ±1% | ±100 | 1206, 0.25 W | Mismatch on value; fits a lower-leakage string |
Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.
The WK, WF..V and WF..N families differ in construction and in the voltage rating they publish per size, so a match on value, tolerance and TCR is where the check starts, not where it ends.
Check the datasheet. The rated working voltage and overload voltage for each size are printed on ASC_WKxxV.pdf, ASC_WFxxV.pdf and ASC_WFxxN.pdf, not in the export. Read the figure for your exact family and size before you fix the number of parts in the string.
How many resistors should an 800 VDC sensing string use?
Enough that no part exceeds its rated working voltage with margin. Four 1 megohm parts in series across 800 VDC put 200 V on each and draw 0.2 mA, so the string dissipates 0.16 W in total, about 0.04 W per part against a 0.25 W rating in 1206.
Power is rarely the limit in a sensing divider; voltage is. So start from the per-part working voltage on the datasheet, derate it for your altitude, pollution degree and transient profile, then set the string length. A 2512 part spreads the voltage over a longer body and may let you use fewer parts; a 1206 string keeps the footprint narrow. Ratio accuracy matters more than absolute tolerance: two ±1% parts from one family track each other over temperature better than a mixed pair, a point our note on divider ratio accuracy explores; use one family for both legs of the divider. A higher value such as WK12V1005FTL cuts bus leakage tenfold but raises the source impedance the ADC sees. Creepage and clearance on the board are set by your safety standard and layout; confirm them with your compliance team.
Can Venatech supply Walsin high voltage chip resistors from Hong Kong?
Yes, to order. All 2,070 parts in this slice can be quoted from Hong Kong; none is on our shelf in Hong Kong (snapshot 9 Nov 2026), so request a quote and we source them through our authorised Walsin channel.
Each quote states availability, date code and lead time for that line, and we work in small lots for engineering builds and pilot runs. We make no stock, price or lead-time promise. The ready-stock list is a dated snapshot that covers MLCC and chip resistors that often sit on the same power board.
How Venatech helps: what should a Taiwan HVDC team send us?
The divider and sense parts from your BOM. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, stating every field where the Walsin part differs from your original.
Paste a divider resistor code into the cross-reference tool, or upload the whole BOM and request a quote through the site. The ready-stock snapshot is dated 9 November 2026. We serve Taoyuan, Hsinchu, Taichung and Tainan from Hong Kong, with fast quotes and small lots. Walsin is the line we are authorised for; Stackpole and Viking are lines we supply.
The short version
Delta Electronics’ October revenue rose 30.1 percent to 74.666 billion New Taiwan dollars, TechNews reported on 9 November 2026, with ±400 VDC power partly shipping and 800 VDC in qualification. Every HVDC stage senses its bus through a megohm divider. Walsin covers that job with 2,070 high voltage chip resistors from 1 to 10 megohm at ±1% or better and ±100 ppm in 1206, 2010 and 2512, and WK12V1004FTL meets a 1 megohm, 1206 brief.
Send us the divider string from your 800 VDC design and we will return Walsin crosses with every difference stated. How many parts does your string use today?
Related reading
- High-voltage chip resistors and the limit nobody checks
- Precision resistor divider ratio accuracy
- What resistor TCR actually buys you
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 19 November 2026.
Sources
Fetched 19 November 2026.
- TechNews (科技新報), report on Delta Electronics and Lite-On October 2026 revenue, 9 November 2026: https://finance.technews.tw/2026/11/09/delta-liteon-oct-30-pct-yoy-growth/
- Walsin chip resistor exports, Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_79.xlsx, re-measured 19 November 2026; Walsin ASC_WKxxV.pdf, ASC_WFxxV.pdf and ASC_WFxxN.pdf datasheets as named in the export; Venatech Hong Kong stock snapshot dated 9 November 2026.
Frequently asked questions
What did Delta Electronics report for October 2026?
TechNews reported on 9 November 2026 that Delta’s October revenue was 74.666 billion New Taiwan dollars, up 30.1 percent year on year, with ±400 VDC power partly shipping and 800 VDC in customer qualification.
What is a high voltage chip resistor used for in an 800 VDC rack?
It sits in the divider string that senses the DC bus for regulation, over-voltage protection, pre-charge and insulation monitoring. It carries a higher working voltage per case size than a general-purpose part.
How many Walsin high voltage chip resistors suit an 800 VDC divider in Taiwan?
We counted 2,070 Walsin high-voltage parts from 1 to 10 megohm at ±1% or ±0.5% and ±100 ppm, in 1206, 2010 and 2512.
Which Walsin part crosses a 1 megohm 1% 1206 high voltage resistor?
WK12V1004FTL, WF12V1004FTL and WF12N1004FTL match at ±1%, and WK12V1004DTL at ±0.5%. Check the working voltage and land pattern on each datasheet before release.
How many 1 megohm resistors does an 800 VDC divider need?
Enough that each part stays inside its rated working voltage with margin. Four in series put 200 V on each; confirm the per-size voltage on the Walsin datasheet first.
Is Venatech an authorised Walsin distributor for buyers in Taiwan?
Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Taiwan in small lots. Stackpole and Viking are lines we supply, not authorised lines.