Czech plants built 1,182,933 cars from January to October 2026, and 41.7 percent were electrified. Every battery-management and inverter board in those cars needs a precision chip resistor somewhere. Walsin Technology (Walsin) lists 8,680 AEC-Q200 TC50 parts, and Venatech is the authorised Walsin distributor in Hong Kong.
This note is for hardware and purchasing engineers at tier-1 suppliers and EMS lines in Czechia that build electronics for hybrid and battery-electric cars. The production figures below come from the Czech industry statistics published on 19 November 2026; they describe cars, not components, and we make no claim about any carmaker’s suppliers or bills of materials. Our part of the story is the resistor list. On 20 November 2026 we parsed Walsin’s chip resistor export (Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_79.xlsx) and counted every part in the automotive TC50 precision series, then checked our own shelf against it.
How much of Czech car production is electrified in 2026?
Just over two in five cars. Prague Daily News reported on 19 November 2026 that Czech plants built 1,182,933 passenger cars from January to October 2026, down 2.6 percent, and that 493,703 of them, or 41.7 percent, were electrified: 199,031 battery-electric, 40,443 plug-in hybrid and 254,229 hybrid.
The split by maker shows where the electronics go. Škoda built 781,069 cars in Czech plants over the period, with 200,368 of them battery-electric or plug-in hybrid. Toyota’s Kolín plant built 185,004 cars, all hybrid, and Hyundai’s Nošovice plant built 216,860, with plug-in and battery-electric models at 18 percent of output, the same report said. Every one of those electrified cars carries a battery-management system, a DC-DC converter and at least one inverter, and each of those boards measures voltage and current with resistor dividers and gain networks. That is the position this note covers.
Where does a precision chip resistor sit in a hybrid or EV?
Wherever a measurement error becomes a control error. In a hybrid or EV, a precision chip resistor sets the ratio of cell and pack voltage dividers in the BMS, the gain of current-sense amplifiers, the feedback point of DC-DC converters and the reference networks of inverter control; a 1 percent part there can cost a whole state-of-charge margin.
Two numbers decide the choice. Tolerance sets the error on day one; the temperature coefficient (TCR) sets how far the value drifts between a cold start at minus 40 °C and a hot underbonnet board. A divider made of two parts with matched TCR tracks well even at 100 ppm, but a gain resistor working against a fixed reference does not. Walsin’s TC50 automotive series combines tolerance down to ±0.1 % with a TCR of ±50 ppm/°C or better, in thick-film construction, and it carries AEC-Q200 qualification, as the series datasheet states. Our comparison of high-precision thick film vs thin film explains when thick film is enough.
How many AEC-Q200 precision chip resistors does Walsin list?
Eight thousand six hundred and eighty. We counted 8,680 distinct part numbers in Walsin’s “High Precision Thick Film chip resistor TC50 (Automotive)” series, in four case sizes and four tolerances, every one at ±50 ppm/°C, from 10 Ω to 1 MΩ.
| Cut of the TC50 automotive series | Part numbers | Rated power |
|---|---|---|
| 0402 | 1,828 | 1/16 W |
| 0603 | 2,284 | 1/10 W |
| 0805 | 2,284 | 1/8 W |
| 1206 | 2,284 | 1/4 W |
| ±0.1 % tolerance | 2,170 | all sizes |
| ±0.25 % tolerance | 2,170 | all sizes |
| ±0.5 % tolerance | 2,170 | all sizes |
| ±1 % tolerance | 2,170 | all sizes |
| Total | 8,680 |
The part numbers follow one pattern: WF, a size code, K for the automotive TC50 series, the resistance code, a tolerance letter and TLJ. WF06K1002BTLJ is a 0603, 10 kΩ, ±0.1 % part. The 0402 range starts at 100 Ω, while the other sizes go down to 10 Ω. Check the datasheet for the series before approval: power derating, the AEC-Q200 statement and the stability figures come from Walsin’s datasheet, not from the code. The chip resistor range page links them.
Do the resistors on the shelf have an automotive precision twin?
Most do. We checked the 191 chip resistor lines on our shelf in Hong Kong (snapshot 9 November 2026) against the TC50 automotive series by case and value: 165 have a twin, so a 1 %, 100 ppm prototype value can move to an AEC-Q200 precision part without changing the footprint.
| Shelf part (general purpose) | Case | Value | Tolerance / TCR | TC50 automotive twin | Match / mismatch |
|---|---|---|---|---|---|
WR06X1002FTL |
0603 | 10 kΩ | ±1 %, 100 ppm | WF06K1002BTLJ |
Match on case and value; tighter at ±0.1 %, 50 ppm |
WR06X1003FTL |
0603 | 100 kΩ | ±1 %, 100 ppm | WF06K1003BTLJ |
Match on case and value; tighter |
WR06X1004FTL |
0603 | 1 MΩ | ±1 %, 100 ppm | WF06K1004BTLJ |
Match; top of the TC50 range |
WR04X1002FTL |
0402 | 10 kΩ | ±1 %, 100 ppm | WF04K1002FTLJ |
Match at ±1 %, with 50 ppm TCR |
WR08X4702FTL |
0805 | 47 kΩ | ±1 %, 100 ppm | WF08K4702BTLJ |
Match; tighter |
WR12X1001FTL |
1206 | 1 kΩ | ±1 %, 100 ppm | WF12K1001BTLJ |
Match; tighter |
WR04X47R0FTL |
0402 | 47 Ω | ±1 %, 100 ppm | none in 0402 | Mismatch: 0402 TC50 starts at 100 Ω; move to 0603 |
WR04W2704FTL |
0402 | 2.7 MΩ | ±1 %, 100 ppm | none | Mismatch: above the 1 MΩ ceiling |
Have part numbers to quote? Click any Walsin part number in the table to open its page and add it to your RFQ, or upload your BOM for a quote, or cross your current part in VenaMatch. E-mail sales@venatech.com.hk or call (852) 2628 4777. We confirm availability, date code and lead time on each quote.
The 26 shelf lines without a twin fall into three groups: 0201 parts (the TC50 automotive series has no 0201), values under 10 Ω, and a few values above 1 MΩ. A tighter twin is still a change: a ±0.1 % part in a circuit tuned for ±1 % can shift a filter or a trip point, so test it on the board, and read the TC50 datasheet next to the datasheet of the part it replaces.
When is a 50 ppm thick-film part not enough?
When the error budget is under about 0.1 percent over temperature. A ±50 ppm/°C resistor can move by up to 0.825 percent across a minus 40 °C to plus 125 °C range in the worst case, so a BMS divider or a gain network with a total budget under 0.1 percent usually needs matched parts or thin film.
That figure is simple arithmetic: 165 °C of span times 50 ppm/°C is 8,250 ppm. In a divider, both resistors drift in the same direction and most of that cancels, which is why a TC50 pair is common in cell-voltage measurement. In a single gain resistor against a reference, it does not cancel. For those positions, compare against Walsin’s thin-film range; our notes on thick film vs thin film precision crossover and precision thin-film tolerance and TCR set out the trade, and the thin-film datasheet states the TCR grades to compare. Confirm any change with your own qualification and your customer’s approval process.
How Venatech helps
Precision values, crossed in one pass. Venatech Limited, Walsin’s authorised distributor in Hong Kong, runs VenaMatch, which decodes part numbers from 18 manufacturers and crosses 800,000+ parts to Walsin, so a BMS resistor list returns TC50 automotive candidates with tolerance, TCR and case stated.
Paste the part numbers into the cross-reference tool, or upload the board BOM and request a quote through the site. The ready-stock snapshot, dated 9 November 2026, lists the general-purpose lines on our shelf in Hong Kong; the TC50 automotive parts are supplied to order through our authorised Walsin channel, and we confirm availability, date code and lead time on every quote. We are Hong Kong-based and serve buyers in Czechia in small lots. Walsin is our authorised line; Stackpole and Viking are lines we supply.
The short version
Czech plants built 1,182,933 cars from January to October 2026, and 41.7 percent were electrified, Prague Daily News reported on 19 November 2026. Each of those cars needs precision resistors in its BMS and power electronics. Walsin lists 8,680 AEC-Q200 TC50 parts, and 165 of the 191 chip resistor lines on our shelf in Hong Kong have a twin in that series.
Send us your divider and gain resistor lines, and we will return TC50 automotive crosses with every difference stated. Which resistor on your BMS board sets your state-of-charge error?
Related reading
- High-precision thick film vs thin film
- Walsin automotive chip resistors: MR, SR and the AEC-Q200 split
- Thick film vs thin film precision resistor TCR crossover
- Cross-reference tool, BOM upload and ready-stock snapshot
Last reviewed: 20 November 2026
Sources
Fetched 20 November 2026.
- Prague Daily News, “Czech automotive production declines slightly as share of electrified vehicles rises above 41 per cent”, 19 November 2026: https://www.praguedaily.news/2026/11/19/czech-automotive-production-declines-slightly-as-share-of-electrified-vehicles-rises-above-41-per-cent/
- Walsin chip resistor export, Venatech_ChipR_Upload_01.xlsx to Venatech_ChipR_Upload_79.xlsx, re-measured 20 November 2026; Venatech ready-stock snapshot dated 9 November 2026.
Frequently asked questions
How many electrified cars did Czechia build in 2026?
Prague Daily News reported on 19 November 2026 that 493,703 of the 1,182,933 cars built from January to October were electrified, a 41.7 percent share, including 199,031 battery-electric cars.
What is a TC50 precision chip resistor?
A thick-film chip resistor with a temperature coefficient of ±50 ppm/°C or better. Walsin’s automotive TC50 series pairs that with tolerances from ±1 % down to ±0.1 % and AEC-Q200 qualification.
How many AEC-Q200 precision chip resistors does Walsin list?
We counted 8,680 part numbers in the TC50 automotive series: 1,828 in 0402 and 2,284 each in 0603, 0805 and 1206, from 10 Ω to 1 MΩ.
Can a general-purpose 1 % resistor be swapped for a TC50 automotive part in Czechia?
Usually on footprint: 165 of the 191 chip resistor lines on our shelf in Hong Kong have a TC50 automotive twin at the same case and value. Test the tighter part on the board before approval.
When should a BMS designer use thin film instead?
When a single resistor must hold better than about 0.1 percent over temperature. A ±50 ppm/°C part can drift up to 0.825 percent across minus 40 °C to plus 125 °C in the worst case.
Is Venatech an authorised Walsin distributor for buyers in Czechia?
Venatech Limited is an authorised Walsin distributor in Hong Kong and serves buyers in Czechia in small lots. Stackpole and Viking are lines we supply, not authorised lines.